What a boss, showing awesome skill cutting a difficult piece to cut just for our entertainment

@thomasjust2663

2 жыл бұрын

This is why the border wall will never work, steel is just to easy to cut thru

Great video showing the use of propane to cut.

Thats a lil baby torch, but you put down a nice line with it

If you've got the farting noise you've nailed it.

The flame is only to get the metal hot enough to reach the activation energy for the oxygen to literally burn the steel. Chemistry is awesome.

@nathanwalker8356

7 жыл бұрын

I literally breath chemistry...lol

@andycraig6905

7 жыл бұрын

Nathan Walker same

@nathanwalker8356

7 жыл бұрын

we all do

@robertatwood2503

6 жыл бұрын

andy craig what a lot of people don't know after the cut is started and you're smooth enough you can turn the gas off in the ignition between the oxygen and the steel will make a damn nice cut

@ChunkyMonkaayyy

6 жыл бұрын

Do I have this correct; The metal is just burning on its own basically? The oxy is just speeding up the process? This is breaking my brain.

Pants tucked in boots must b an IRONWORKER LOL

I have never had to cut a rail track. Mostly 516 plate, triple three, 106 and 36 WF. Like to try it one day. Good cut. However, you want to see some insane flame burning, check out the crazy shipbreakers in places like Turkey and Pakistan. Yikes, everyday is a lottery with life when it comes to them guys. Scary stuff.

Wooow This Is Awesome I Love Gas Cutting.

great torch!!!!!

I just went through education for cutting rail and this right here is impressive as hell. Its hard to see from the flame lines if they are bending in the bottom of the head and foot/midsection connection if so the cut might be a bit too fast. Id hate to grind it to the 0.3mm tolerance. But still just getting the piece to drop freehand is hella impressive, well done.

@artides

8 ай бұрын

Thanks

Exelente!!!

great cut!!!

what size tip are you using?

Crazy steady cut! Crazy Skilled !

Getting there keep up the practice

@artides

3 жыл бұрын

I want to see your cut then

How much pressure we use for cutting?

@artides

3 жыл бұрын

It was so long ago but I think Oxy 300 and propane 120...sometimes it went up for the scrap cutting- quicker cut but not very neat, plus oxy and propane waste

Nice

good

Gas cutting looks pretty cool but I'm not giving up my everlast plasma cutter anytime soon.

@washingtonapple

4 жыл бұрын

Even an 80 amp plasma cutter would do a very poor job of cutting that rail. A 40 amp wouldn't have a prayer. Plasma cutters are incredible machines for cutting plate but they have trouble with cutting very thick steel.

@poland_stronk3044

8 ай бұрын

Kurwa gościu z palnikiem i butlami to podjeżdżasz do torów ciach prach i szyny już w bagażniku. A plazmą...

레일을 옆으로 넘어트리면 한번의 동작으로 자를 수 있습니다.

مطلوب لمبه قطعيه واسطوانات

Cut railroad tracks one second, cook a steak the next. What more could you want?

Awesome cut ! Can I ask what were both regulators set at ?

@artides

3 жыл бұрын

400 oxy, 150 propane...What I remember... used BOC equipment. With Railtech 300 and 50Kpa... Usually you can go by the look of the flame...

The little torch that could

@randomrandom3065

4 жыл бұрын

It's a 3 barrel. It's short but it definitely ain't little

how can I contact you about using some of this in a documentary?

@artides

10 ай бұрын

I’m giving you permission to use this video in your documentary…

@michaeldillonfilms

10 ай бұрын

thank you so much. Shall I credit you as Artides or something else

@artides

10 ай бұрын

@@michaeldillonfilms Artides should be fine. No worries

Why were you cutting the rail?

@hiseminencetheholymacdiarmada

6 жыл бұрын

Switchpoint Productions - It's an instructional video, there could be hundreds of reason why one might need to cut a steel rail. I went off this video to cut an 18" section to make a light/medium duty anvil, worked perfectly.

@artides

6 жыл бұрын

Training purposes

中国私人拥有这块轨道钢 够判几年了吧

Is this just an example of a torch in use? You can break RR track

@artides

4 жыл бұрын

Dave Watson we are still using them occasionally...Most popular atm is Railtech...First cut in life track has to be done by torch, if you would use Flexi cutter when rail is under pressure your blade would jam...Plus if you are good at oxy cutting its way quicker

That is , at most 1 minute cut..

Tip size and pressures please :)

@artides

6 жыл бұрын

Don't remember exactly , oxy 300 ,propane 150.. 20mm tip

@garythesquidsquid7779

4 жыл бұрын

@@artides thats the tank, not your guages

@artides

4 жыл бұрын

Garythesquid SQUID Not sure about pressure...

I only saw one gas being used, were they mixed? What gas was used here. Why has no one asked?

@artides

2 жыл бұрын

Propane plus oxygen…propane-flame and oxygen …

is it not oxy acetylene ? can propane cut that hot

@luisff7030

7 жыл бұрын

Yes it can. First the flame heat the metal until it start to melt, then a jet of pure oxygen burn all the metal in contact and make the cut. Pure oxygen in contact with liquid metal will burn the metal and produce heat + oxidized metal. What really cut is the jet of oxygen, the flame is only to heat and melt.

@Len_M.

7 жыл бұрын

Rob N It goes Propane, MAPP, then Acetylene in terms of max flame temp. It doesn't really matter during a cut though, cause if you really wanted, you could turn the fuel gas right off after initializing the cut, cutting on pure oxygen alone.

@ales_xy

7 жыл бұрын

Exactly. Google "thermal lance" or "oxygen lance". Another nice toy for big boys :-)

@davidr.massey419

4 жыл бұрын

Len when i was running simultaneous 4 torch set-up on my burning machine cutting 10" thick A-36 mild steel bearing caps one of my inner torches preheat shroud extinguished leaving just cutting Oxy stream still cutting for 30" inches of the cap until it lost the cut turning the bottom corner of that big "C" shaped bearing cap.. Had really primmo equipment and recovered the cut finishing all four caps. Inspecting the quality of the cut one-- the cap that ran with no gas shroud---that cut was clean square with no blems.

@Comm0ut

Жыл бұрын

LP permits MUCH thicker cuts because acetylene explodes at high pressures and withdrawal rates.

Cool..! Well...not cool - very hot.... You know what I mean?

oxy propane is great!!!!!!!!!!!!!!!!!

What the hell are you doing you start from the top. 💥🧑‍🏭 Gravity like melted lava. I was using a Vector 2000 torch.

@artides

3 жыл бұрын

When you cut the rail in CWT you are starting from the bottom , if you will start from the head the foot will snap if under tension (may go on the angle ,head won’t)

इसको katne ke liye kitna presser chahiye

@artides

Жыл бұрын

300 propane , 150 Oxygen…BOC torch/set up

maybe would have been beeter with cutting disc?

@robkennedy3000

7 жыл бұрын

Would depend on why its been cut :)

@plasmaoc

7 жыл бұрын

Yeah fair enough.

@artides

6 жыл бұрын

Training purposes. Less noise , when rail is under pressure you shouldn't use friction saw. Head hardened shouldn't be cut with the flame

Propane may be the cheap way, but it sucks for heat on a torch. And what was the purpose for this video?

@artides

5 жыл бұрын

Shawn Hammack We can’t use acetylene...

@emilmuhrman

4 жыл бұрын

@@artides Why can't you use acetylene?

@artides

4 жыл бұрын

Emil Muhrman Thermit welders are the usually qualify to use propane as fuel. I was using Acetylene underground because propane same as petrol is prohibited(underground)...It was very similar just hotter (my experience)...

@emilmuhrman

4 жыл бұрын

@@artides Ok, thanks for the explanation. I have only used acetylene.

Good night

@BabluKumar-ht2lp

3 жыл бұрын

7493060570

Power of Oxy-Propane

Не понел!прикол,в чём.

1:15 Did anybody else check their phone?

@artides

3 жыл бұрын

Nope

@truthsmiles

3 жыл бұрын

@@artides I did haha. That little buzz sounded like the vibration from a message notification.

Hack saw would be better for this I cut these every day by hand

@CoolKoon

8 жыл бұрын

The hell you do, troll!

@Prawnchowmein

8 жыл бұрын

hahahahaha

@renatorenteria5568

7 жыл бұрын

Prawnchowmein

@joshuaheppner6806

6 жыл бұрын

I usually just rip rail off with my bare hands. I'd know I'm a section laborer ;)

@joehumpston7937

5 жыл бұрын

you must have a sh!t-ton of Energy! I mean, cutting a piece of Railroad track is a back-breaking task! I couldn't even do it with a grinder and cut-off wheel!

Armor piercing

So that what chuck Norris use to get a hair cut🤔

Витя также резать любой металлов былой резко конструктора модели трактор малек самоделки для косить к сеновал Сены заготовки зима скотами коровы даются богатых витамины молока.

Glad I don't work with you we would be there all week ffs scrap out for network work do about 100 cuts in 3hrs a night easy you make it look hard 😁

@artides

Жыл бұрын

The kid was in training , this was his second or third cut. I can say he did amazing job. I’ve seen people who can cut , I’m not the best but I can cut too.

@deantrueman4347

Жыл бұрын

@@artides didn't know you was teaching him yes a great job to say he's just started took me ages to sort my pressures out with no gauges 👍

Sangat mudah

@fahddavid9178

3 жыл бұрын

kzread.info/dron/UysvCiv4WVlykK6vgobyTg.html

I would have went through it on the first RIP. Though good job💪💪👌

@aspincelaframboise5300

5 жыл бұрын

BULLSHIT!!!

Good job sir.please tell me the combination of gas and oxygen when rail piece cutting.i am railway serwant.

@artides

4 жыл бұрын

Rajnikant Patil 400 on the oxy and 150-200 on propane: BOC cutting torch. Different torch, different pressure. After pressing the trigger you should hear hissing noise and you have nice flame with small blue crown...

😂😂

ah use a reely sherp file...it it only takes a day or too

Get a real torch out rook.

@jordanwomack2334

5 жыл бұрын

About 200lbs of oxygen and 100lbs of propane coming through a #6 tip on a Harris 62-5. That’s how you cut railroad iron. Or you just get out a labounty msr shear on the end of a 80,000lbs trackhoe

@artides

5 жыл бұрын

He was learning that day ...I’m using Harris torch now, not much difference...

@jordanwomack2334

5 жыл бұрын

Besides the fact that they are better?

@boots7859

3 жыл бұрын

OK Jordan, everyone here knows you the man.... (Jordan is my nieces name too...)

I hate gas cutting

@artides

4 жыл бұрын

Hadi stop it

Ебатть, а КАК?