Oxidized Fiberglass Gelcoat Restoration With 3m Perfect It Compound and Wax
How to do a restoration on oxidized gelcoat with 3M perfect it compound and wax. This Boston Whaler Dauntless 18 had some moderate oxidation on the hull. I go through the steps on restoring a boat gelcoat by wet sanding with Scotch-Brite Gray Pad 37448, following up with the Scotch Brite White Pad 7445 and then compounding and waxing with the 3M perfect-It products.
You can find the materials I used in this video on my affiliate links below:
Gray Sanding Pads: amzn.to/3kepQzT
White Sanding Pads: amzn.to/3ODdYp5
3m Multi Pack Pads: amzn.to/3KvLvyp
TCP Global Wool Buffing Pads: amzn.to/3vHmAm4
7/8" Buffer Backing Pad: amzn.to/3KlVmXc
3M Medium Perfect It Compound: amzn.to/3MvKh7t
3m Perfect It Boat Wax: amzn.to/36NnF38
Please visit out Amazon Storefront where you'll find many of the tools and materials we use in our videos.
www.amazon.com/shop/josesextr...
00:00 Introduction
00:26 What You'll Need
01:11 Washing the Boat Down
01:51 Wet Sanding with 3m Gray Pad 800 Grit
02:54 Wet Sanding with 3M White Pad 1000 Grit
03:56 Comparison Between Wet Sanded Areas
05:08 Compounding the Gelcoat
07:55 Comparing the Compounded Area
08:28 Waxing the Hull with 3M Perfect-It Wax
10:05 Wrapping it up
#Boat
#GelCoat
#Oxidation
Пікірлер: 28
just bought my boat ..its been sitting covered up for a while..Can't wait to get at it .... Thank you for the no-nonsense.
@ExtremeDIYGuy
6 ай бұрын
You're welcome good luck on your project!
Nice job and beautiful boat! I don’t know why I watched the whole video as I don’t even own a boat!😂 Maybe Someday though!🤞🏼
@ExtremeDIYGuy
10 ай бұрын
Maybe one day!
When I wet sand I use a bucket with water and couple drips of dish soap!! Works really well.
@ExtremeDIYGuy
2 жыл бұрын
That's a great idea!
Looking great!
@ExtremeDIYGuy
2 жыл бұрын
Thanks!
Nice boat 🚢
@ExtremeDIYGuy
2 жыл бұрын
Thanks!
Used this product on all my cars and tried it on my whaler after a wetsand and its great stuff! Brough the gloss back after I wetsanded to get the nasty orange peel out of the paint.
@ExtremeDIYGuy
Жыл бұрын
Thanks for sharing!
Thanks for the video. I got a Dauntless 17 and this job is coming up... I have to fix some spidercracks first.
@ExtremeDIYGuy
Жыл бұрын
Your welcome!
From what I am reading, the sanding you did prior is not needed from the blend of the 3m cut. I am about to do this job on my dauntless today. Thoughts? How it holding?
@ExtremeDIYGuy
Жыл бұрын
IT's holding great. Wet sanding with 1000 or 1500 cuts through a lot of the oxidation so it's easier to polish.
What did you mix in the water to sand off the oxidation?
@ExtremeDIYGuy
Жыл бұрын
Nothing, just plain water
I thought the Perfect-It Medium One-Step had wax in it. Why did you use a separate wax? I bought the One-Step Medium w/ Wax.
@ExtremeDIYGuy
2 жыл бұрын
It does, I figured an extra coat of wax can only help!
Nice going, I recently bought a 92' Montauk, inside was painted whaler blue but is chipping off pretty bad, I went to clean it and even the scrub brush has knocking it off. What do you recommend doing? I'd rather it be original looking.
@ExtremeDIYGuy
2 жыл бұрын
You can try sanding it off but you'll have to restore the gelcoat underneath. Also, scraping the loose bits off is an option as well but you'll have to be careful not to scratch the finish underneath. Personally, If at all available to you, soda blasting is probably the best bet but can be costly.
@benc1927
2 жыл бұрын
@@ExtremeDIYGuy Not bad idea, the paint is so lose that when using a plastic brush with soap on it I saw good bits of it coming off. Also I taped off a few point and when I pulled the tape back it took like 30% of the paint off. Maybe jsut a power pressure washer?
@ExtremeDIYGuy
2 жыл бұрын
Definitely, If its that loose I would try the power washer, jut be careful to use a wide fan pattern and not get to close to the Gelcoat!
@paulbriggs3072
2 жыл бұрын
Even if you did damage the gelcoat, after sanding it, you simply roll on an epoxy barrier coat (epoxy fairing compound can be used for dings and gouges), wet sand that, and you're ready for new paint. I would use a 2 part catalyzed finish after all that work.
@ExtremeDIYGuy
2 жыл бұрын
@@paulbriggs3072 Check out my series on restoring a classic 13 whaler. After glassing, fairing compound was what I used to level everything out, after a ton opf fairing and sanding, an epoxy barrier coat was next (3 coats) before the two part poly.
Hope the license sticker holds over the wax.
@ExtremeDIYGuy
2 жыл бұрын
The license sticker is sticking pretty well. Like all mountains of license plate or boat registrations, impossible to peel off!