Overheating Fixed with Bleeder Valve│Nissan D21 Hardbody
Автокөліктер мен көлік құралдары
Discovering the bleeder valve was the cause of the Nissan D21 Hardbody running warm after fixing the major overheating issue. Hopefully, this helps, bleeder valves are on many other vehicles and if excess air is in the cooling system it can be used to remove it. This simple fix can save you on diagnosis fees. You could perform this entire job without any special tool.
Check out the products below that were used in the video to support the channel
Products:
Coolant: amzn.to/37HQmMD
Spill Free Funnel: amzn.to/3hdPGlf
Wobble Socket Extension: amzn.to/2KLWCtH
Chemical Gloves: amzn.to/34F1rvP
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing.*
Disclaimer:
Due to factors beyond the control of Mello Motorsports, I cannot guarantee against improper use or unauthorized modifications of this information. Mello Motorsports assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Mello Motorsports recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Mello Motorsports, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Mello Motorsports.
Пікірлер: 13
I dropped my bleeder valve bolt and it took me two hours to find it. I had to take out the alternator because it was stuck behind it and there is no way to get to it. Not even with a magnet. It was a nightmare. I recommend just loosening it till it almost comes out and don’t take it out completely. That way the air bubbles can still get out and then tighten it back down.
@ethan....
2 жыл бұрын
if you put a piece of paper on the head of the bolt and insert it into the socket it can't fall out and you can re-install it without dropping. Hope that helps you next time.
@fungdart
2 жыл бұрын
@@ethan.... Good idea. Next time I will definitely do that.
@TEREK1
Ай бұрын
I dropped mine too and know where it is but it's impossible to get without taking everything apart. After hours of trying to get it I decided to just replace it with a new one, just don't forget the washer.
great angle on the bolt, super easy to find after watchin your vid, thanks amigo
Hey guys. I’ve had 4 of these trucks, and only my most recent one had that mpi systems sticker on the intake. Anyone know why it’s there?
I have a question ? What size is the threat of the bolt .
I got a question I get no water coming out of the little hole or bleeder hole
@mariolara3503
2 жыл бұрын
Did u find the problem?
@tonygomez4485
2 жыл бұрын
@@mariolara3503 Yes I did, anytime you have overheating problems if you put an aftermarket thermostat, never use an aftermarket, go to the Nissan dealer and buy the original for that type of engine, I’m here in Canada and it cost me around $56 tax included, it should be around $45 US I had no more overheating problems and I left the truck running for and hour without the radiator cap, after an hour I closed the radiator cap, temperature did not go over the one quarter on the gauge and stayed there, water finally came out of that bleeding hole, it worked out well. I hope this long explanation work
@mariolara3503
2 жыл бұрын
Thanks for the info I'm on my way to the nissan dealer 😁
@tonygomez4485
2 жыл бұрын
@@mariolara3503 Awesome, all the best my friend 👍🏽🙏🏽
And don’t lose the copper washer that goes underneath the bolt.