Outboard Motor shuts off?
Ойын-сауық
Mercury 2.5 2 stroke outboard troubleshooting. Does your outboard motor shut off while driving your boat? In this video I cover the basics of understanding, troubleshooting and diagnosing problems with my small Mercury outboard engine. I found the problem with my engine and it turned out to be a simple problem that is easily resolved. The fuel vent valve is essential and an easily overlooked potential problem that can impede fuel flow and your engines ability to start or run properly.
If your outboard engine is shutting off this video might help you identify the problem and determine a solution. Small outboard engines are not very complicated but if you do not complete all of the steps or perform each step properly, you can have problems starting or operating your outboard motor.
Timestamps
00:00 Introduction
00:39 Small 2 stroke outboard motor starting process
01:25 When your outboard shuts off on the water
02:24 Diagnosing what went wrong with my Mercury 2.5 2 stroke outboard
02:51 Gasoline engine basics
04:01 Potential things that might have caused the problem
05:15 What was wrong with my small outboard engine
08:00 Starting the Mercury 2.5 outboard motor
09:38 Conclusion
#outboardtroubleshooting #mercury2stroke #smalloutboardproblems
❤️ Subscribe to my KZread Channel / waynetheboatguy
📷 Follow me on instagram! / waynetheboatguy
☞ Follow me on TikTok! / waynetheboatguy
▶︎▶︎▶︎Playlists About Boats
🚤 Tiny Boat/Jon Boat Stuff • Tiny Boat - Little Boa...
💰 Boat Shopping • Boat Shopping
🐋 Boston Whaler • Boston Whaler Videos
🛥 Boats, Boat Trips & Boat Accessories • Boats, Boating Trips, ...
⚡️ Electric Boats & Electric Boating • Electric Powered Boats...
🛶 Kayaks & Kayaking • Kayaking & Kayak upgrades
🪦 Curtis Creek Maryland Ship Graveyard • Curtis Creek Maryland ...
🎲 Boating Shorts • Boating Shorts
▶︎▶︎▶︎Boat Engines & Motors Playlists
⛽️ 2 Stroke Outboard Motors • 2 Stroke Outboard Engi...
⚙️ Volvo Penta Maintenance & Repairs • Volvo Penta Maintenanc...
🌎 Newport NT300 electric outboard • Newport NT300 3 hp Ele...
🚽 Evinrude 2 - 2 hp engine • Evinrude 2 - old Evinr...
🔒 Seized Suzuki DF20 • Suzuki DF20 Short Shaf...
🔧 Inboard/Outboard Maintenance • Inboard Outboard (Ster...
▶︎▶︎▶︎ Boat Repairs & Projects Playlists
🛠 Low Cost Boat Repairs & Projects • Low Cost DIY Repair & ...
🔨 Boat Transom Projects • Boat Transom Projects
🧰 Boat Repair & Maintenance • Boat repair, maintenan...
🛞 Boat Trailer Projects • Boat Trailer Repairs &...
▶︎▶︎▶︎New Boater Playlists
📌 Boating Education & Tips • Boating Education and ...
📓 Boating Basics • Boating Basics for New...
🆘 Boat Safety • Boat Safety - videos t...
❄️ Boat Winterization • Boat Winterization
Sound effects and additional music is copyright free from iMovie
Пікірлер: 88
I had the same thing happen to me on the maiden voyage of a skiff I put together. Got out into the river and ran around a little bit and then all of a sudden the motor bogged down and shut off. What was worse my wife was with me and thought I built the boat badly and was worried about getting back. Luckily I quickly noticed the bulb valve on the gas line had collapsed. I realized there was a vacuum in the line and I loosened the air intake on my fuel tank. She started right back up and I earned my wife's respect and admiration for figuring out the problem and fixing it.
@WayneTheBoatGuy
2 жыл бұрын
Glad it worked out! We don't too many chances for our significant others to gain back our trust on the water!
Spun prop hub bushing thankfully I had the trolling motor but man did it take a while to get back wish I had my spare prop. Lesson learned
@WayneTheBoatGuy
2 жыл бұрын
Dang - it's challenging to try to think of everything you need when you're out on the water!
Your videos are excellent - Top class
Great video it happens to me too that second day I took the boat out
Spot on film again Wayne, always honest which helps more people. Fuel filters are another thing neglected by many people. I still miss the music....
@WayneTheBoatGuy
2 жыл бұрын
Thank you!! I'll have music in next week's video!
Thank you for taking the time to make videos like this. As a new-ish boater (This summer was my first summer owning a boat) with a 2001 Mercury 125 2 stroke outboard, videos like these are invaluable!
@WayneTheBoatGuy
2 жыл бұрын
Thank YOU - great to hear! There is a lot to learn and it never seems to end.
Amazing video Wayne!!! You just made my day!!! 👍
My friend had this exact same issue with his generator. And of course it was storming, the commercial power was out and the wife and kids were all fussing about how long was it gonna take before they were comfortable again lol. There’s a lot of tasks that have to be handled for a successful day on the water. Very easy to overlook something, especially if you’re at a public ramp that’s busy, and everyone is waiting to launch or retrieve boats. You try to hurry so you don’t have the ramp traffic backed up and overlook something.
Thank you! I just got my first outboards, just like this one, for my little Javelin sailboat. Had a similar issue and could not speed up the boat, only in low power, but also I didn’t open all the away the vent. Will try that next time
Enjoyed this mate, its fun for me to learn about this stuff.
Been watching your vids for research. Thinking about picking up a sun dolphin 12 American and a Coleman 5hp outboard. Great vids man. Wish I could do boating vids, maybe eventually
This was the first mystery I encountered when I got my first boat back in '99. I was 19 and didn't even know what a vent cap was :D
@WayneTheBoatGuy
Жыл бұрын
Yeah - we don’t encounter a lot of this stuff until we’re boating!
I bought a slightly used 3.3hp merc's the other day for my dinghy. The seller had only used it a hand full of times and just had it serviced. I had the exact same issue when trying to start for the first time. I thought I bought a dud but after 15 minutes of analyzing I realized it was the air flow valve wasn't open far enough. After that it ran like a dream. Glad to see I'm not the only one. Great outboard, love it! Great Video.
@WayneTheBoatGuy
Жыл бұрын
Thanks! I just wish these could shift into neutral!
@mycoolo304
Жыл бұрын
@@WayneTheBoatGuy Do you mean reverse? Reverse gear would be nice.
Great video - I've also seen it where the vent vibrates itself closed while running!
@WayneTheBoatGuy
2 жыл бұрын
I have an old Evinrude 2 with a metal one that I totally could see that happening!
Been there... done that 😂 Enjoy your videos. Thanks.
@WayneTheBoatGuy
2 жыл бұрын
Welcome!
Great video
Tks bro for the sharing ur experience
@WayneTheBoatGuy
Жыл бұрын
My pleasure!
Great tutorial !!! Like number 717 👍
2 cycle motors? My No.1 rule is I don't leave fuel in the tank overnight. I pour the mix back then run the carburetor dry, always. I just bought an air cooled 4 cycle. Tiny and smooth. I'm going to love it.
Thank you!!!!!!!!!
Thanks. I just got a 14 foot jon boat with that same motor.
Drove me crazy too. However, I found that my vent didn't work at all for my 2.5hp Merc. I took apart the fuel cap and I found the factory had put a rubber plug in the air way that prevented air flow. Pulled out the plug and now the vent works just fine.
Thank you
Dude, thanks for the videos. You like Norm McDonald.
it is true for any trouble shooting, the culprit is very often the most simple item that is overlooked.
@WayneTheBoatGuy
2 жыл бұрын
Couldn’t agree more! Thanks
Definitely know how that feels I was in the st. Johns River and my motor stopped and the current was pulling me out throughout my anchor luckily I got picked up by the US Boat Club
Good to know
Wow this thing happened this weekend on the lake. I could have sworn that I also tried to start it with the cap off and it still wouldn’t start. I think The motor I have is a little older than yours and has a red engine stop button but no pin or lanyard I’m real frustrated. Thanks for the video for me thinking
thank you ,, I think I am having the same problem ill check tomorrow
@WayneTheBoatGuy
2 жыл бұрын
good luck - hope that's all it is!!
@USA4thewin
2 жыл бұрын
@@WayneTheBoatGuy exactly what it was big thanks
The exact same thing happened to me a couple of weeks ago. But I am brand new to boating. But I have a 2015 Tohatsu 5HP with an external tank. But it did it after I had ran it for a while. At first I had no issues and then it started bogging and shut off a few times. I’ll would wait a few second and it would start right away. I managed to get back to the ramp and when I was home I noticed the tank was squished inwards. I opened the cap and heard “psssssss” sound. Like air breathing in. Turned out that was my issue. I took it on the water last Saturday and had no issues. I didn’t know I was supposed to have that breather port open. I had closed it a day prior.
I had an issue one time where I had accidently bumped my engine into gear with the engine off while I was fishing. When I went to restart the engine it wouldn't start because it was in gear. Drove all the way back to dock with my trolling motor before figuring out what happened.
thanks Wayne ! i have a beginner question is my 2.5hp outboard, when i go fishing on my dingy, i always do stop and go to find the candy spot, while the engine is off and i am fishing in that spot for 10-20mins, should i leave the fuel cap valve open and the choke open, and fuel switch in open for my next quick and easy start to my engine? many thanks in advance, learns many boating knowlege from your channel!!!
@WayneTheBoatGuy
Жыл бұрын
I usually don't turn off the fuel or close the vent until I am done for the day. You shouldn't need the choke once the engine is warmed up - unless it has trouble starting.
@kawasakiwaverunning
Жыл бұрын
@@WayneTheBoatGuy appreciated the very valuable information & the lighting fast response! Thx!
Thank you : I just could not understand why my Merc 2,5 wouldn’t start, the breather on the cap was open but…..not enough !
@WayneTheBoatGuy
2 жыл бұрын
It really should just pop open when we pull the cord!
I don't know how many times I've been yanking my starter rope, then realizing my kill switch was on, on my four wheelers!
My list of backup plans😂 Backup plan 1: fuel and choke (elbow grease) Backup plan 2: take the thing apart on the water feel with finger for spark and see if it’s wet reassemble and more elbow grease Emergency plan: row home like a normal person 😂
Yup same thing happened yo me a few weeks ago... wait till a sheer pin breaks and you are panicking thinking the work you did on the lower unit broke the shifter...
@WayneTheBoatGuy
2 жыл бұрын
You just never know what's going to shut you down!
Got a yamaha 90 2 stroke. Starting right away when its warm. As soon it get cold you have to crank for a while to get it going. Carburators clean, tank has no water, also it sometimes dies on idle. Any guesses? ;)
OFTEN with a remote tank and fuel line with primer bulb they develop air pockets in the 6 or 8 ft.fuel line especially when not run for 2 or 3 weeks and you need to let the air out. CHEERS from Canada
@WayneTheBoatGuy
2 жыл бұрын
Great point!!
Your engine seems to start in gear. Does it not have in gear or neutral? I have a Mercury 3.3 which I bought new in 2016. I always seem to be fixing it. Mostly it starts on 3 pulls when cold. Re-starting when warm is a big problem. I'm close to giving up on this motor but I really like that it's not too heavy for me to lift off and on my dinghy.
@WayneTheBoatGuy
Жыл бұрын
Yeah this motor has no neutral or reverse it’s always in gear. If warm starts are an issue, have you tried different choke settings? Mine sometimes like a little choke when starting warm and other times it likes the choke fully open.
Yup... done it more than once.
How do I adjust the tilt on a little motor 2.5 model mercury thanks
Not new to this, but I had the problem. I noticed that you opened the vent ALL THE WAY. Just cracking the vent doesn’t do it. The way the cap is designed, it can require the vent to to cranked all the way open. Thanks.
I have this exact motor and can't find what type of gasket I need to order for the top of the foot. It's leaking gear oil there and I wanna fix it before I put it on the water. Any suggestions?
👍
My boat is tied up on the river Bank now stranded waiting for the mechanic, Yesterday I ran aground on some rocks so I checked propeller that seems fine spins freely but the engine won't start. I tried starting it with choke on and it starts and runs fine but as soon as I turn off choke engine cuts out and won't restart unless choke is on. Any ideas?
I got a similar outboard, but mine is 3.3hp 2001, am new to the game, when you first start the outboard and set the choke, after it has been running, do you undo/put the choke back to off? Mine starts and it has some white smoke, old gas that the old user had? Any suggestions?
@WayneTheBoatGuy
Жыл бұрын
Yeah as it is warming up - push the choke back in. Give it just enough choke to keep it running. After a couple minutes it shouldn't need any choke and when you re-start it within an hour or two it might not need any choke. The smoke is normal - it's a 2 stroke. Just be sure to mix your gas/oil properly.
Thanks for the "simple straightforward" advice, I to forgot to vent my gas tank the first time out & it shucked all the air outta my tank & stalled (rather alarming the first time out) common sense isn't so common.....😒
What year is your motor shown in the video?
@WayneTheBoatGuy
Жыл бұрын
I think it's a 2004
👍🎣⛵💯
Hello brother so i have a MERCURY 7.5hp and it has been sitting for a long period of time and like the head of the motor it doesn't rotate left or right what should i do brother ✌.
@WayneTheBoatGuy
2 жыл бұрын
First try pulling the spark plug (or plugs) and spraying some lubricant in the cylinders and let it sit for a day or two.
@zahoor3160
2 жыл бұрын
@@WayneTheBoatGuy thank you so much brother
@garymacpherson7355
2 жыл бұрын
Pour 2 cycle oil down cylenders
😂 that just lets you know how fuel efficient the motor is 😂 I didn’t think it was ever going to quit.
I went to the lake today my boat shop running I'm thinking that would be the same problem
@WayneTheBoatGuy
Жыл бұрын
hopefully that's all it was for you!
Is power running out of gas starved for gas ⛽
Head gasket is bad
@WayneTheBoatGuy
2 жыл бұрын
That's a really interesting thought! If I ever experience this again in the future - and it's not the vent - that's a really solid suspect.
At 8:56 I thought. of the SpongeBob accented narrator.....
@TheNockingPoint
2 жыл бұрын
I just learned about these sayings. this year.... my teenager thinks I am so behind the times.
@TheNockingPoint
2 жыл бұрын
My teenager did not think it was funny when I used the 1-hour version after he finally got a stud out of a 30-year-old exhaust manifold he was trying to save.
@WayneTheBoatGuy
2 жыл бұрын
"Three Hours Latahh" lol
Darn took you 10 minutes to say. Open your vent 😢
Why do you have white axes spray painted on your trash cans
@WayneTheBoatGuy
2 жыл бұрын
For yard waste!