That's crazy cool! Great tips for building this! Love the sound kit! Those links are really tiny. So cool! Thanks for sharing this Tim! Thumbs up bro! 👍

@rcnewb

5 жыл бұрын

Thanks, man!

Great video, I’ve only just bought this kit today so this video will definitely be very helpful, thank you for taking the time to make the video it is now saved and I will take time to watch it many times wile I wait for it to get here , I’m busy with three rc car builds just now an Fg marder a Losi ten rally x and my new Arrma Infraction speed run build , so plenty to keep me going but I had to have this kit , stay safe .

great tip on the body reamer. I used a tiny drill bit and just hand turned them a couple times just the very top or entrance of the screw holes for the ball joint

Definitely plan on getting one of these tiny bad boys one day. Thank you for sharing.

@rcnewb

5 жыл бұрын

Thanks for checking out the video! It's a fun project to take on.

the 0,7 and 0,9 hex bits from the ifixit kit where perfect for the ball join.

@rcnewb

8 ай бұрын

Thank you for the tip!

I got one just recently as I preferred the look of the D110 over the Jeep. So I transferred all my good parts over and just bodged the Jeep to fit a random esc/rx with transmitter I had spare and not using. I love the car, it's an amazing little RC, a real pain to work on, the lights more so than anything else. I have a couple tips too, the first for the ball studs is to take the allen key and cut it so you can use it in a pin vice drill, makes mounting the balls so much easier without the need to reem. The second, if you want a few more degrees of steering angle, on the front axle there's a screw that holds the end cap in place. The one on the front side that the steering arm on the wheel hub can touch, remove it and cut the little plastic collar off that it sits in, then cut a small bit off the screw or else it will press into the axle and prevent it from turning. My D110 now turns tighter than my previous Jeep.

@rcnewb

5 жыл бұрын

Thank you for the tips, Drew! If I decide to build another one of these little rigs, I'll keep that information in mind.

What worked well for me was just cutting the little allen key and put it in the electric screwdriver/drill. This way you can push much harder with the thread of the balljoints against the plastic holes. Just let it turn as slow as you can. And set the slip on the lowest. In case you would turn it too far it will just stop turning instead of stripping the hole. But better just go slow.

Nice man you did a really good job on it!

@rcnewb

5 жыл бұрын

Thank you, sir!

Great video 👍👍

Tamiya is making a very nice mini soon, looks like loads of fun too.

@rcnewb

5 жыл бұрын

Cool, I missed that news/announcement. I'll have to do a bit of research into that model.

Awesome video

@rcnewb

5 жыл бұрын

Thank you!

Semi-Pro tip: the manual is printed to scale, so all the screws, bearings and assembly lengths are printed 1:1. I started out using digital calipers before realizing I could just hold the parts up to the picture to confirm lengths With that out of the way, is there some sort of oil or grease we should be using on the gears? I know that's typical in larger RC but I didn't find anything in the manual, and I would almost think the kits would come with some.

Is it possible to have proportional steering and variable throttle depending on the transmitter/reciever set used?

I have heard that the charger that comes with this works for the scx 24 also ???

Does RCMart have any free shipping promotions? I'm trying to order one but they what $65 for shipping.

The paint on that body is insanely good of a job. Did you paint it with one of those tiny hobby brushes?

@rcnewb

4 жыл бұрын

Thank you! This was a 100% aerosol spray paint job. I masked off the roof and went to work. :)

👍🏽 👍🏽

epic a03

wich cable Connect D4L and Body because i have this model 99% ready i Just need this cable. Can someone maybe send a Link or somethinke

What battery did you use?

That's nice but to small part wise for me.

What charger do you use?

What mount did you break, i didnt break any and i have the same problem. Did you ever fix it? If so, how did you. I think my issue is that the ball ends are loose

@rcnewb

4 жыл бұрын

The "cup" end of the link mount cracked, which makes the link move around much more than it should be. I haven't looked into fixing it, but might take a closer look at it again.

@Prelude_user2022

4 жыл бұрын

Oohh, i broke the mounting on the center gearbox but if you broke the little ear shaped links there should be like 4 spares in the box

What kind of paint did you use how did u paint it?

@rcnewb

Жыл бұрын

I used Tamiya TS-28 Olive Drab for the main body and Tamiya TS-26 Pure White for the roof. I painted the roof first and then masked it off to paint the rest of the body.

stl for the little crawling blocks?

@rcnewb

4 жыл бұрын

Hi Mark! That’s a file that I whipped up but haven’t posted anywhere. I may put it on Thingiverse and can send you the link if/when it’s up.

@markd4542

4 жыл бұрын

@@rcnewb Awesome! Thanks. Would be great to add to the other Orlandoo stl's and maybe encourage others to remix, and add on. Ive printed a couple terrain flats that i chopped up from others designs but am going to make some changes as they are not quite scaled right for this little truck.

GOOD😄

I have seen these Kit's in 1:87 scale...now that's tiny, think their call micro

What kind of paint do u use?

@rcnewb

Жыл бұрын

Tamiya TS paint. I gave more detail in a reply to your other question. I hope that helps!