I love the part where you say "The flight controller says 'oh blimey!' " 😂 In all seriousness, though, thanks for all these amazing videos. They are so incredibly useful!!!!

@Painless360

7 жыл бұрын

+Orange RC happy flying!

So simple when you know how !! :-) Thank you, have a good day Steve

Easy to understand as ever, thanks for the Vid

Simple and to the point. Thx.

Thanks for this video. I really appreciate that.

thanks for the video. i haven't found anyone able to explain this

Really useful video, thanks.

This is very useful especially for cleanflight :)

Great video, well explained. Can I ask about the "96" keeping them the same I notice you are 12 short on the left 1012 and not on the right roll (only 5 short) 1995. Probably doesn't make much difference but doesn't it mean you can roll harder left than right, or are there dead zones at the end?

@Painless360

8 жыл бұрын

You can use the settings to get both ends the same but in practice there will be very little difference. Happy flying

Hi, do you advise to do this in Cleanflight as well? Or is it not that picky? Thanks, and keep those great videos up!

@Painless360

8 жыл бұрын

This should be done with almost all. Happy flying!

Is there a way to increase servo travel beyond 100 percent? I wanted to get more travel out of a servo driven pan/tilt gimbal. I know with my DX9 I can increase servo travel up to 150 percent. Can the Taranis do such or something similar?

@Painless360

7 жыл бұрын

Yep - enable the extended trims option in the lower half of the 'Setup' menu on the radio for the model you are looking at..

Hi and thanks I've subbed. Can you tell me do you centre the main trims first or get close to the 1500 with the trims and then use sub trims? I have occasional yaw drift on one of my ships.

@Painless360

8 жыл бұрын

+shlllong use the process in this video with the trim switches in the middle, default position. If you've got drift and the channel value for yaw is 1500 then I'd recalibrate the gyros/accelerometers. Best of luck!

@shlllong

8 жыл бұрын

+Painless360 OK many thanks and lastly if min throttle is set at say 1060 and Max is 2000, will that make any difference on say yaw pitch and roll with the minimum numbers of 1000 and mid points of 1500 that you speak of?

@Painless360

8 жыл бұрын

Not sure what you're asking. Refer to the manual for the flight controller you're using. I normally like 1060-1940 range or a little more on the main fight controls (yaw, pitch, roll).. Best of luck!

Opentx is awesome. I was wondering if buying the Turnigy 9XR Pro was a bad idea. While it does have its drawbacks in quality it makes up for in this type of access and Jr module flexibility. For me it was price and features. But I can say I like it, the buttons have been updated, mine are very nice, there is only one 3 way switch, but it does need tweaking.

@Painless360

8 жыл бұрын

I've not used it here but lots of pilots use and like them. Best of luck!

I realize this video is a couple years old now but should I be concerned if my channel ranges are outside what Mission Planner considers normal (1100 to 1900)? I have an X10s radio, with R9M, bound to a R9 Rx. My FC is a Pixhawk (version 1) with latest firmware. My default ranges are MIN= 982 and MAX= 2006. Should I adjust my endpoints to fall within the "normal" range? Or does it matter?

@Painless360

5 жыл бұрын

Ardupilot won't like channel ranges that are too much - see the Pixhawk & Pixhawk 2.1 series..best of luck!

How exactly does this apply to the throttle? idle (1000), mid throttle (1500), and max throttle (2000) ?

@Painless360

6 жыл бұрын

+Bernard Adderley exactly tge same, although the mid throttle position isn't as critical..

Recently got a QX7, however I'm having trouble getting my sticks endpoint to reach 1000 and 2000 microsec, on all gimbal inputs. The Min and Max are all on 100%, but max deflection is around 1200 and 1800 microsec. Is there a way to solve this? I'm relatively new to rc flying

@Painless360

6 жыл бұрын

I'd rerun the calibration.. See the videos on the QX7 on the channel..

@daytontang3148

6 жыл бұрын

Painless360 ok ty. I’ll go n try.

@daytontang3148

6 жыл бұрын

Does ail and ele mixing affect the endpoint of the sticks. I currently have an elevon setup.

@Painless360

6 жыл бұрын

Nope, unless you've reduced the travel in the mix/servo screens..

What is the PC software you're using to show the values on the controller?

@Painless360

Жыл бұрын

kzread.info/dash/bejne/pniOu7qxXbW2kqg.html happy flying!

@rogerclark1480

Жыл бұрын

@@Painless360 yikes, I've had companion since I got the X9D, just never looked at that page. Thanks!

@rogerclark1480

Жыл бұрын

@@Painless360 - sorry to bother you again, but I don't think what you're using to show the change as you move the sticks is companion. I have the latest copy and I don't see that screen/page/tab anywhere in there. Also, the screen you're demoing is in color. Am I totally missing something?

@Painless360

Жыл бұрын

It helps me if you can let me know at what point in the video you are referring to. If it is the same as in the thumbnail then that is Mission Planner, part of the Ardupilot family... Happy flying!

@rogerramjet8016

Жыл бұрын

@@Painless360 - I think you are using BetaFlight or ClearFlight or somthing like that. It's the screen that shows the microseconds responding while you move the sticks on the Taranis. I don't think anything in Companion will show that information.

Can it help me in stabilizing the quadcopter ??

@Painless360

5 жыл бұрын

Please see my bind and fly betaflight setup video that goes through all the steps you need to go through to get a quadcopter setup well. Best of luck

@sss_1707

5 жыл бұрын

@@Painless360 But I am with mission planner all setting are at the mark but it still flips on takeoff. I noticed that my endpoints are going too far from normal range. Can it be the problem ?? Please help

@Painless360

5 жыл бұрын

@@sss_1707 kzread.info/dash/bejne/gmin0bRvgcq1m5M.html all of that is already covered in playlists and videos.. Best of luck!

My 360 servo syill spinning 360...

Blimey! ÷)