Nicely done video. You answered all my questions even things I didn't think about. Enjoyed a full-watch. Yup, I can imagine digging the pit holes for the lift panels in that hot, humid heat. I'm going through that type of heat spell now. Have a fine week. 👍🏽🤠 8/27/23

Great review, love the flush mount. I think this is the type of lift for me.

Team scissor lift here. Thanks for your update. Clean install.

Well done! What a clean look

Nice video! Thanks for posting!

Nice Lift! I have max jax in my garage, but i'd definitely get one of these if my ceiling was high.

That is awesome how it's flush with the garage floor

I have one of these, too, just not flush mounted. Love it. Perfect for home garage. I cut the beeper wires first thing lol. And I'll say that I 100% agree with your assessment, it's a great setup.

@FredAllenBurge

3 жыл бұрын

Good idea! Thay beeper is loud lol

@jeffreygwinn5081

2 жыл бұрын

Hey guys, how far from the front wall did you all mount yours. I do work here and there on different vehicles. Would love to lift some bigger SUVs here and there.

@jeffreygwinn5081

2 жыл бұрын

@@FredAllenBurge , help me out...lol

@FredAllenBurge

2 жыл бұрын

@@jeffreygwinn5081 my pit starts 8' from the front wall and that leaves just enough room for a bench and some walking room. 10' would be a lot better though if you have the space

@jeffreygwinn5081

2 жыл бұрын

@@FredAllenBurge Thanks! I ended up doing 7' from the front wall. Mine is just sitting on top bolted down. I'm going to save up and countersink it next year. What a difference this makes! Thanks again.

Great video.

Other than the seriously-loud music, great and informative vid - thanks!!

I had a QJ and really liked it. I have never considered a scissor lift, they had zero appeal to me…until now. I really like how this one was mounted. I like how it could be used as a table if you wanted. I think this will be my next lift. Very impressed. Good video and really good job on the install of the lift.

@FredAllenBurge

10 ай бұрын

Thanks Todd I appreciate that👌

@MoparGuy1625

9 ай бұрын

I’m in the same boat. Have the QJ but like this set up way better.

Thanks. I will try and let you know!

Nice mods to perfect the set up.

That's how I want to do mine.... But struggling for head room so thinking of getting a mid rise lift and dig half pit so can Stand underneath. Just the concrete strength may be lost where the pit is 😕. How sturdy is yours at full height with a car on it?

Thanks for the Video. I was wondering is there is enough room under the car to pull a transmission and manipulate an exhaust?

Nice video! We just got our Rav 535 lift from Italy. It was 9500$ so way more expensive than a Twinbush, but its a 3.5t lift what should be a little under 7700 pounds. After our bad experience with our 1 post made in China lift, we decided to get a lift made in Germany or Italy.

@richharr

Жыл бұрын

I just bought the same lift used. Pretty good so far, i was pushing it by loading into the bed of my pickup. That thing is heavy

@lukasmeyer1992

Жыл бұрын

@@richharr It is working so nice. Its now 3 months in use and wehad zero issues. I like how easy it is to put a car on the lift and how stable they are on it.

@lukasmeyer1992

4 ай бұрын

@@stefanolci1708 First it would not work, then the wiring fell apart, it was not welded straight, it started to wear a lot. It was also starting to bend before reaching its supposed max weight. The side opposing the Lift was always hanging down, more with heavier car. Also the tolerances were really bad, what led to the cars on the lift moving more than they should.

@lukasmeyer1992

4 ай бұрын

@@stefanolci1708 1 Post 2.5T mobile Lift, no real brand. Looked like the RP Tools one, but they fixed many of the issues on the new one.

Am also looking for a lift, and came across your video, I think I will be ordering this one in the near future, looks like the most usefull for me :). But I have one question, aren't the wide plates a disadvantage if you want to work on the sills for example? We have standard 1 phase 230v 16 amps, so I hope that the lift rises a bit faster in my case 😬

@FredAllenBurge

3 жыл бұрын

The wide plates have been no big issue for me personally. If you do a lot of body work maybe another style of lift could be ideal

Yeah man!

Hello, what thickness and width are the arms of the scissor ? Thanks.

I left the ramps on mine and just leave them level with the rest of the lift. It allows me to have a longer car on the lift. If I need to drop them down I can. I did my pour ahead of time. It was a bit of a pain to get the measurements correct.

@johnwalters878

Жыл бұрын

I really wanted to like this lift. After all the work to get the concrete floor poured to fit the ramps, hide the hoses and the flush mount worked perfectly. It still allows me to use the ramps for longer vehicles. Unfortunately the lift will not lift a car after it ever stops mid-raise. I have got nothing but run around from Dan at Twin Busch. They blame my power, no high magnetic breaker, low voltage, etc. I ran a dedicated 30 amp circuit. It just bogs and won’t run with weight on it. They don’t stock a new motor. It’s literally never worked other than lift itself. It’s out of warranty and basically scrap. Save your money and buy a bendpack or nussbalm

@johnwalters878

10 ай бұрын

I am still getting the run around from from them. They say I don’t have enough power, and that electricians don’t know anything ( literally ) it’s still never worked and they won’t sell me a new motor even. It’s pretty much scrap metal at this point. My last ditch effort will be to remove the motor and have it looked at locally. Even if I do get it working, I doubt I will ever trust it. So I think either way I will get rid of it. I really hope you have good luck with yours.

Nice review on the lift! Do you have any issues doing transmission swap, engine swap, or exhaust work with this lift? How much space do you have in the center? I've been debating between a 2-post and a scissor lift like yours.

@FredAllenBurge

3 ай бұрын

No it's perfect for all those projects 👌

Thanks for the info Fred! Could you tell me how tall your ceilings are where your lift is set up? I'm at about 10 and a half feet high, that being said I'm unsure if this lift would be over kill for me and if I should go with the lower option scissor lift, let me now what you think! Thanks

@FredAllenBurge

11 ай бұрын

I had the trusses built up with a peak in the middle to maximize headroom, that was necessary to make full lift height work for my shop. At 10' flat ceilings I think a small car's roof is going to be very close to hitting.

Great video man! Now I'm designing my workshop, something small just for my own use, and I don't know at what height to stop. I want to make it as small as possible because the winter is very cold here and I want to heat it. Please tell me how high your garage is above the elevator, (I make the ceiling straight, I don't have a slope) Thank you

@FredAllenBurge

6 ай бұрын

Thanks! Height of you shop then will probably depend upon height of average car you intend to lift plus about 6' for the space to walk under. That's how I determined if my shop could accommodate this lift olus a mid sized car. I measured all my cars from frame rail to roof + 6' and tjat showed me that it could be done. Good luck on your shop!

Sorry if you allready mentioned in a video, just didn't watch it all. But my question is, can you place lift panels wider or narrower than what is supposed to be by sellers spec? Thanks!

@FredAllenBurge

2 жыл бұрын

No I dont think so

Thank you for the detail. I’m about to form-out the concrete; would you be able to provide the dimensions for the recessed hole? The manual says: 82”x25.5”x4.3”. Also, would a 3” pvc pipe be enough to act as a conduit, to run the hose and lines? Thank you

@FredAllenBurge

2 жыл бұрын

3" pvc should work yes, mine is no larger than that. I'd strongly suggest waiting on concrete until you get the lift there. The manual is not accurate in dimensions plus you may want to remove the ramps as I did and that will change the dimensions also. Let me know if you still want dimensions and I'll measure it for ya.

@Fernando-ns3uv

2 жыл бұрын

@@FredAllenBurge I would love to wait for the lift, unfortunately, I’m forming them, this week, and pouring the concrete on Friday. If you do not mind measuring yours, I would greatly appreciate if; additional what is the thickness of the pad that’s underneath the lift? Their website has one set of measurements, and their documentation has another. I called, they told me that the pad can be 2”, meanwhile, their documentation says it needs to be 7.8”.

@bkingtz1

2 жыл бұрын

@@Fernando-ns3uv I know 9 months have passed since you made your comment but i had to replay, K can't believe they told you the thickness of the pad can be 2" when it should not be less than 7.8" (20cm) by all standards.

i'm sold

Nice lift and install is on point but holy smokes batman over 2 min just to go up and down? Probably fine for home use but wont work in my shop

Hey Fred Great video,, how deep are the recesses in your concrete, sorry if youve answered this before but the manufacture says its 110mm drive on but your recesses look lower , and your installation looks great by the way.

@FredAllenBurge

Жыл бұрын

Thank you👍 I'll have to measure that for ya, I can't recall now it's been a few years.

@snakesound

Жыл бұрын

@@FredAllenBurge AWesome Thank you

@FredAllenBurge

Жыл бұрын

@@snakesound approximately 4.25"

this is a nice lift - half the price of nussbaum. my only gripe with it is the blue. wish they had gray or black.

@FredAllenBurge

2 жыл бұрын

Agreed, black or grey would be ideal for me too, it would be very easy to repaint though

@JayDee-xj9lu

Жыл бұрын

I think Nusbaum goes the highest. I have a 2 post Nusbaum but I'm moving house soon and I don't do a lot of mechanical work any more and those 2 posts really get in the way when your parking your car in between them. I also have a 18 foot hovercraft and the scissor would be ideal to lift it. I guess no one hoist is perfect for every job.

I couldn't work under a lift like that. When the rear platform support rolls that far forward of the rear vehicle lift point it looks super sketchy the way the vehicle is balanced and the platform is weighed down.

@FredAllenBurge

9 ай бұрын

I find 2 post lifts with those two small pads per side to be way more sketchy. Lots of fail videos out there of those😬

Thanks for this video! Have you tried to lift a truck? I have a doge ram 1500 crue cab. In your opinion can it lift the truck?

@FredAllenBurge

Жыл бұрын

No I havent tried, not enough space in my shop to fit the length of the truck really

I plan on sinking mine next year. But have run into an issue with narrow framed SUVs. I've seen an adapter kit, and one guy uses 4x4s. Have you run into that yet?

@FredAllenBurge

2 жыл бұрын

No I haven't but I only work on small to medium sized stuff

@4961Studebaker

2 жыл бұрын

Consider cross bars from Stratus scissor lifts, I bought and use them for narrow suv/truck on a bendpak flush scissor.

Hello, do you have a dimensions of your shop?

My only concern is using a transmission jack for a transmission on a truck or suv or a frame mount fuel tank

@bruizer28

2 жыл бұрын

I was curious if there was enough width between to get a transmission jack through also

I have a question that is probably a bit unusual. I'm struggling to find a scissor lift that lifts about as high as this one, but doesn't need to lift more than approx. 150 kg. The size and height of the lift you show is ideal, and should only lift a maximum of two adults for use with a larger astronomical telescope. I therefore do not need a double lift like you have, nor as powerful. Do you have an idea where I can find such a lift at a good price? Thank you in advance.

@FredAllenBurge

3 ай бұрын

I wish I could offer a suggestion but I really don't know what would be best in that situation honestly.

Hey mate what about drainage from spillages etc? I'm soon to be installing one and thinking i might put a pipe with holes sunk into the dirt with a grate for water, coolant etc to drain into

@FredAllenBurge

Жыл бұрын

Ive never had any big spills in the pits but ya that's a good idea if you expect to spill a lot

@lukecrane774

Жыл бұрын

@@FredAllenBurge yeah I often hose and pressure wash my epoxy floor as a part of weekly house keeping.

@lukecrane774

Жыл бұрын

@@FredAllenBurge also did you just use a standard engine crane to drop the units in?

@FredAllenBurge

Жыл бұрын

@@lukecrane774 yes I used my cherry picker. The lifts are extremely heavy though, if you have access to a tractor or forklift that would be ideal

How did you get the PVC pipe from the pit to the wall?

@FredAllenBurge

Жыл бұрын

It was poured in place when the floor was done

Could you move them apart with ramps on ,so you could drive thru or store a car under the one on the lift ?

@FredAllenBurge

Жыл бұрын

No I dont think that would work

@randolphsnyder1505

Жыл бұрын

@FredAllenBurge Thank you,but just noticed that lift discontinued anyway.

So what are the actual dimensions? Have they corrected the wrong information on the website?

@FredAllenBurge

9 ай бұрын

I would call them to verify dims if you are doing a floor before you have the lift. I think now they sell one for in-floor mounting actually

Did i miss it or why didn't you just use the S3-18 for Underfloor Mounting?

@FredAllenBurge

9 ай бұрын

Didn't exist at that time or wasn't available in the US anyway

Would I be able to lift my Yukon slt with your lift?

@FredAllenBurge

5 ай бұрын

I believe so

What was the cost of this lift? Including installation, did you have to hire an electrician?

@FredAllenBurge

Жыл бұрын

I did all install work except the concrete, wiring is just a 110 outlet. $3800 shipped for the lift I believe it was.

@victorcortez4369

Жыл бұрын

@@FredAllenBurge thanks for the info, I'm contemplating to buy one , you definitely did a great job! Looks very professional!

What size is your shop?

@FredAllenBurge

10 ай бұрын

25x50 approximately

@CarSharingJho

9 ай бұрын

@@FredAllenBurge how tall is your garage?

en tudom a minosegi munka es a minosegi anyag a mai gazdasagi viszonyok kozott de a sokszori hasznalat utan mennyi oldal kilengese lessz majd stabil marad ???? Oooo yes

Actually made in China! No joke

@bkingtz1

2 жыл бұрын

They are made in Germany, I have two post. Even if they are made in China, why would that be the problem if it is made under license. Most top quality companies have their products made in China because of cheaper labor and parts. Problem with products made in China comes from unlicensed or fake stuff.

@byrdguu

2 жыл бұрын

@@bkingtz1 true

@cameronearnshaw2259

2 жыл бұрын

@@bkingtz1 Twin Busch is a German company, but the lifts are made in China.

Jeez I didn't realize it took so long to lift. That is painful.

Great review, love the flush mount. Think this is the type of lift for me.