thanks a lot i did the calibration and the printer worked. Thanks
@rajeshkushwahaa2 жыл бұрын
Very good work
@adesuyatno9452
2 жыл бұрын
.
@ptp79 Жыл бұрын
I am getting error on Olivetti MB2 printer after installing a new ribbon cartridge "Please use the original ribbon". Any solution to this? As I want to use compatible ribbon in it.
@mikidjuka54462 жыл бұрын
when i turn on the printer olivetti pr2 plus flashes BREAK and lights ON, how do I solve the problem. Thank you dear friend
@nurulhasaniabdulrahim837
2 жыл бұрын
Do full service and dismantle machanicm check board clean up maybe got stapler bullet inside still happen change mainboard and printhead
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 ok thanks a lot i solved the problem by cleaning the sensor shell
@SudhanshuKumar-ix8cl Жыл бұрын
The station 2 light blinks whenever I start the printer kindly guide
@nurulhasaniabdulrahim837
7 ай бұрын
Unplug com port cable and calibrate still happen replace printhead and clean photo sensor /mainboard
@asikhussain Жыл бұрын
How to solve USB is not woking problem in logic card?
@nurulhasaniabdulrahim837
7 ай бұрын
Check interface parallel / com / USB or Replace new logic board
@sumitpanwar942 жыл бұрын
Sir printer is not printing properly. After printing 1 2 page properly, printer is making sound (dhak dhak). Kindly suggest something what is the problem as we have done internet explorer print setup setting also but printer stops printing good format after doing good format printing for 1 2 pages. When it makes unusual sound its alignment got distorted. Printer keeps on printing right aligned after this sound. Kindly help
@nurulhasaniabdulrahim837
2 жыл бұрын
Pls tighten carriage belt remove top cover screw potition at the back try unscrew and fix back
@rubenboavida26122 жыл бұрын
My Olivetti pr2plus printer after switch on ready & station1 leds lights are blinking. What isd solution?
@nurulhasaniabdulrahim837
2 жыл бұрын
Remove machanicm and service printer try to clean mainboard (head cleaning spray) still got issue pls replacement mainboard
@mikidjuka5446 Жыл бұрын
Respect, Olivetti pr 2 plus the left half of the paper has no print and the right half of the paper has a print. How to solve the problem? Thank you
@niknasrul7186
Жыл бұрын
Print test page to check how many printhead pin left. Then check mylar. Mylar cannot move around while printhead is moving
@sergiomissaglia63807 ай бұрын
Can you print images with it ?
@nurulhasaniabdulrahim837
7 ай бұрын
do you mean print result after calibrate ? can see minutes 1.53
@angvrg2 жыл бұрын
Break Button light blinking continuously
@nurulhasaniabdulrahim837
2 жыл бұрын
Test few time maybe can
@mikidjuka54462 жыл бұрын
I have a problem with olivetti pr 2 + pulls in the paper and throws it out immediately, how to solve this problem. Thanks
@nurulhasaniabdulrahim837
2 жыл бұрын
Do calibration and check results
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 when I do the calibration light sation 1 and sation 2
@nurulhasaniabdulrahim837
2 жыл бұрын
@@mikidjuka5446 full service and takeout machanicm check board and cleaned
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 thanks a lot of serious problem just like you said
@mikidjuka54462 жыл бұрын
pull in and eject the paper immediately, how to solve a problem. thanks
@nurulhasaniabdulrahim837
2 жыл бұрын
prob Paper pull and eject normally printhead issue Can try to calibrate first pls unplug printer cable before calibration refer video and still happen change printhead ..another issue change head cable with Printhead and check results
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 thanks a lot i did the calibration and the printer worked. Thanks
@mnsani77943 жыл бұрын
Buat rakaman semula. xjelas lah . xdgr. sendiri rakam ka. good job.
Пікірлер: 35
thanks a lot i did the calibration and the printer worked. Thanks
Very good work
@adesuyatno9452
2 жыл бұрын
.
I am getting error on Olivetti MB2 printer after installing a new ribbon cartridge "Please use the original ribbon". Any solution to this? As I want to use compatible ribbon in it.
when i turn on the printer olivetti pr2 plus flashes BREAK and lights ON, how do I solve the problem. Thank you dear friend
@nurulhasaniabdulrahim837
2 жыл бұрын
Do full service and dismantle machanicm check board clean up maybe got stapler bullet inside still happen change mainboard and printhead
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 ok thanks a lot i solved the problem by cleaning the sensor shell
The station 2 light blinks whenever I start the printer kindly guide
@nurulhasaniabdulrahim837
7 ай бұрын
Unplug com port cable and calibrate still happen replace printhead and clean photo sensor /mainboard
How to solve USB is not woking problem in logic card?
@nurulhasaniabdulrahim837
7 ай бұрын
Check interface parallel / com / USB or Replace new logic board
Sir printer is not printing properly. After printing 1 2 page properly, printer is making sound (dhak dhak). Kindly suggest something what is the problem as we have done internet explorer print setup setting also but printer stops printing good format after doing good format printing for 1 2 pages. When it makes unusual sound its alignment got distorted. Printer keeps on printing right aligned after this sound. Kindly help
@nurulhasaniabdulrahim837
2 жыл бұрын
Pls tighten carriage belt remove top cover screw potition at the back try unscrew and fix back
My Olivetti pr2plus printer after switch on ready & station1 leds lights are blinking. What isd solution?
@nurulhasaniabdulrahim837
2 жыл бұрын
Remove machanicm and service printer try to clean mainboard (head cleaning spray) still got issue pls replacement mainboard
Respect, Olivetti pr 2 plus the left half of the paper has no print and the right half of the paper has a print. How to solve the problem? Thank you
@niknasrul7186
Жыл бұрын
Print test page to check how many printhead pin left. Then check mylar. Mylar cannot move around while printhead is moving
Can you print images with it ?
@nurulhasaniabdulrahim837
7 ай бұрын
do you mean print result after calibrate ? can see minutes 1.53
Break Button light blinking continuously
@nurulhasaniabdulrahim837
2 жыл бұрын
Test few time maybe can
I have a problem with olivetti pr 2 + pulls in the paper and throws it out immediately, how to solve this problem. Thanks
@nurulhasaniabdulrahim837
2 жыл бұрын
Do calibration and check results
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 when I do the calibration light sation 1 and sation 2
@nurulhasaniabdulrahim837
2 жыл бұрын
@@mikidjuka5446 full service and takeout machanicm check board and cleaned
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 thanks a lot of serious problem just like you said
pull in and eject the paper immediately, how to solve a problem. thanks
@nurulhasaniabdulrahim837
2 жыл бұрын
prob Paper pull and eject normally printhead issue Can try to calibrate first pls unplug printer cable before calibration refer video and still happen change printhead ..another issue change head cable with Printhead and check results
@mikidjuka5446
2 жыл бұрын
@@nurulhasaniabdulrahim837 thanks a lot i did the calibration and the printer worked. Thanks
Buat rakaman semula. xjelas lah . xdgr. sendiri rakam ka. good job.
@nurulhasaniabdulrahim837
7 ай бұрын
Hp cap ayam ini je yg ade
How to solve blinking station 1 and 2
@nurulhasaniabdulrahim837
2 жыл бұрын
Service and check mainbord replacement needed
tak dengar la suara merdu
@nurulhasaniabdulrahim837
3 жыл бұрын
Posa