This video will cover how to setup the Okuma Crown for production #lathe #cnc #okuma
Жүктеу.....
Пікірлер: 10
@sachithpriyanandaАй бұрын
Hi, I am trying to get the load monitor work in OPS U100 L controllers , which is very similar to this as it looks, however i can not find where the load values installed after teaching mode, could you please help me with this
@aaronrunk4209
Ай бұрын
I'll have to do some more looking on this however when it comes to the teaching mode it sounds more like a mazak but if you are wanting to make sure that your work offsets are in the right locations you could go into MDI and send it to a known location to see if it has been set correctly. I will say your values are on the screen somewhere it's just kind of hard to find them on these older machines
@user-zg5vd2gl6n9 ай бұрын
make a video on how to set up and bind instruments on Haas!!!!! Please .
@ssleddens2 жыл бұрын
Nice
@aaronrunk4209
Жыл бұрын
Thanks
@jakub1517 ай бұрын
How would you load a program onto this machine using the RS-232 port?
@aaronrunk4209
7 ай бұрын
At minute 2:30 in this video. kzread.info/dash/bejne/o6eDzdqygq_Hkqg.htmlsi=LR5tsmWtOEB7MYHq I'll go over how to load from an RS-232. I know it's not the same machine. However, it should be very close, just different buttons
@aaronrunk4209
7 ай бұрын
When I get back to the shop I'll look to see if I can figure out how to do it and if I can I'll record it and send it as well
@aaronrunk4209
7 ай бұрын
Thanks for watching
@jakub151
7 ай бұрын
@@aaronrunk4209 No problem would be much appreciated! I have a Okuma Crown 762e OSP700L control fyi.
Пікірлер: 10
Hi, I am trying to get the load monitor work in OPS U100 L controllers , which is very similar to this as it looks, however i can not find where the load values installed after teaching mode, could you please help me with this
@aaronrunk4209
Ай бұрын
I'll have to do some more looking on this however when it comes to the teaching mode it sounds more like a mazak but if you are wanting to make sure that your work offsets are in the right locations you could go into MDI and send it to a known location to see if it has been set correctly. I will say your values are on the screen somewhere it's just kind of hard to find them on these older machines
make a video on how to set up and bind instruments on Haas!!!!! Please .
Nice
@aaronrunk4209
Жыл бұрын
Thanks
How would you load a program onto this machine using the RS-232 port?
@aaronrunk4209
7 ай бұрын
At minute 2:30 in this video. kzread.info/dash/bejne/o6eDzdqygq_Hkqg.htmlsi=LR5tsmWtOEB7MYHq I'll go over how to load from an RS-232. I know it's not the same machine. However, it should be very close, just different buttons
@aaronrunk4209
7 ай бұрын
When I get back to the shop I'll look to see if I can figure out how to do it and if I can I'll record it and send it as well
@aaronrunk4209
7 ай бұрын
Thanks for watching
@jakub151
7 ай бұрын
@@aaronrunk4209 No problem would be much appreciated! I have a Okuma Crown 762e OSP700L control fyi.