PERFECT thank you bud. Worked spot on.

You sir are a legend!

Just done mine after private garage service, 2.2 2010 worked a treat. cheers dude

@TheOnlyMosesMalone

8 жыл бұрын

You're very welcome. Glad to have helped :-)

Brilliant, worked first time, thanks for the vid 👍👌

Thanks for this video, just worked for me. Perfect

Just reset mine. Thanks for sharing

By the way, I just earthed mine directly to the chassis, made sure of good connection. All good. Cheers

Worked for me. Thank you!

Worked for mine. Thanks 👍

@aaronlenton3511

6 жыл бұрын

(I didn't bother using a switch, just inserted wire into T shaped bit and connected to negative terminal on battery)

Thanks!

Thank you 🙂👍

Thanks for this - it works!! Just to add - for simplicity - the other pin in the free socket is actually ground, so all you need is a short (*~10cm) male-male patch wire, to plug between the two pins, shorting them. Long wire going inside the cabin and an on-off switch are not necessary, also looking for a ground on the chassis. etc.

@TheOnlyMosesMalone

6 жыл бұрын

pumpal LKT You're very welcome and thanks for the comment! Cool, I didn't know that. I initially thought you had to ground the wire after turning on the power (hence the switch) however I believe you can do it before aswell.

@aaronlenton3511

6 жыл бұрын

Hi, to clarify, I can just plug in some sort of wire, ground it, get in the car, do the 5 depressions of the accelerator and that's it?

@TheOnlyMosesMalone

6 жыл бұрын

Aaron Lenton Essentially yes :-)

@aaronlenton3511

6 жыл бұрын

Thanks a lot. Just out of curiosity what year is your car?

@TheOnlyMosesMalone

6 жыл бұрын

Aaron Lenton 2010. Just make sure you have the same socket as in the video.

Hey! Did DPF regeneration work after that?

Reset mine. Thanks for the video. But it made my check engine light come on and my glow plug light keeps flashing and it has turned my traction control off

Hi, thanks for the video, I have a block in the place where you are putting in the wire, should I remove the block and if so how? I don’t want to tug on it too hard and damage it....

@TheOnlyMosesMalone

6 жыл бұрын

Sheik F Hi Sheik, it sounds like this method may not be suitable for your car. What year is it?

@sheikf6781

6 жыл бұрын

Morgan R thanks for the reply Morgan, it’s a 1.6 2010 model. It has those black boxes which I can see you have, but mine is also in the section where you have put the wire into.

@TheOnlyMosesMalone

6 жыл бұрын

Sheik F Ok sorry I don't know about the 1.6 engine. Have you looked into Forscan? It's free software you can use.

@sheikf6781

6 жыл бұрын

Not a problem I’ll look into it, thanks for your help!

Hi, Thanks for the video. But is it normal that you are hotwiring the battery? If i make this connection without the switch i'm getting sparkles and the wire is heating up. I used the right pin as seen in the video. I measured it, and apparently there is 12 v on it with almost no resistance. So i don't get it why you should connect it to the chassis? This will shortcircuit the battery

@TheOnlyMosesMalone

5 жыл бұрын

Hi thanks for the comment. To be honest I'm not sure but I wouldn't think the pin should be seeing 12v. This procedure is from the Mazda service manual but only applies to the 2.2 diesel models. Cheers, Morgan

Which pedal ?😅

Can you advice how to reset 2014 Mazda 6 . 2.2 diesel.. my low pressure warning light is on.. dealer told me once the oil is change It needs to reset.. they would do it for me but the charging cost is ridiculous.

@TheOnlyMosesMalone

6 жыл бұрын

david wong Hi David, have you tried clearing all error codes with a code reader? You can pick them up for about £20 but I'd recommend using Forscan (free) with a modified elm obd2 reader ( about £15 ebay).

@dw1hkdavidtkwong

6 жыл бұрын

Morgan R thank you very much

@dw1hkdavidtkwong

6 жыл бұрын

Sorry being so dense, is forscan a brand or obd2 reader another thing? I searched for one on eBay, it's a red case unit is that the one? Here is the URL..www.eurocarparts.com/ecp/p/tools/car-service-tools/diagnostic-tools/diagnostic/?553997350&0&t5_399&gclid=CjwKCAjw3rfOBRBJEiwAam-GsMXv9z2B94hLDso6gyxM2T2Xrnnq78wfMjssbV5A2FlkogsfFWlnvBoCyjsQAvD_BwE

@TheOnlyMosesMalone

6 жыл бұрын

david wong Hi David, Forscan is free software you can download for your laptop. It's a "modified elm 327" you'll need to search for. There's a few on eBay and usually say Forscan in the listing.

Hi I tried this on my mazda3 sport 185, had a flashing dpf light since last service, the lightwasnt on when it went into the garage so they couldn't reset it. I've done this today and the light went off for 5 seconds and then started flashing again, the same thing happens when I clear all faults on my obd reader. Any idea what could be the issue? Using the obd reader it shows 0 known faults

@TheOnlyMosesMalone

2 жыл бұрын

Hi Matt, did they definitely change the oil at the last service? Have you checked the level on the dipstick? Diesel builds up in the sump of these cars due to the regeneration of the DPF. I believe the light will flash if the level is too high (from diesel dilution) That's from memory though as I know longer have the car. Cheers

@mattmulroy7210

2 жыл бұрын

@@TheOnlyMosesMalone thanks for your reply. Yes it was definitely changed, and is just about at the f line on the district, nowhere near the x mark, starting to think it may be the timing chain in which case it won't be worth fixing (owned the car for 5 years) I would have thought a fault code would show for the timing chain. Each time I scan it doesn't find any faults

@TheOnlyMosesMalone

2 жыл бұрын

@@mattmulroy7210Yeah doesn't sound like that's the issue then. Are you using Forscan? I believe there is a function in that to see how much the timing belt has stretched.

Does this method also work to reset ecu for the Fuel Additive eolys after a top up?

@TheOnlyMosesMalone

7 жыл бұрын

Dimple Lau Hi, I wouldn't think so. There may be a similar process but not this exact one. However, look into Forscan, it's a free program that allows you to do servicing on your car, all you need is a £7 tool (I got mine of eBay). That's how I now perform this process so it may work for the eolys too. Cheers, Morgan

@dimplelau5401

7 жыл бұрын

Ramteq Thank you very much for some sound advise. I've actually tried two elm devices that haven't done the job. The first from ebay was sold by someone advising to buy their more expensive ELM327 as cheaper ones might not work with FORScan, which I purchased and it couldn't even establish a connection with the car. The second cheaper one established a connection with the car but FORScan came up with a message stating something about clone ELM working with many other Software but not theirs. Don't know whether I should risk wasting money on another one. Do you have an ELM device you can recommend?

@TheOnlyMosesMalone

7 жыл бұрын

Dimple Lau Hmmmn that's not good. We're the devices advertised as "modified", they need an additional switch fitted to allow different parts of the car to be read. Was yours Bluetooth?

@dimplelau5401

7 жыл бұрын

The one that didn't work at all was described as modified and has a switch. No info was provided to state which position is HS or MS, but I've tried everything and it doesn't work. Maybe just a defective product and needs replacement. If only the ebay seller was faster with communication.

@TheOnlyMosesMalone

7 жыл бұрын

Dimple Lau I can send a picture of mine if you'd like. Are you turning the car to "ON" (without starting the engine) when trying to connect?

Just don't change your oil and filter at 10 000 miles. 5 000 miles (10 000 km) maximum if you want your engine and turbo to last

Hatte nicht geklappt.