Simple yet helpful, thank you so much for doing this!!!
@MrKotecake8 жыл бұрын
Simple and easy to follow, thanks for the video.
@valentinstegaru37228 жыл бұрын
You maked verry simple in 6 min. THX!
@frankmunro13039 ай бұрын
Enjoyed that, I just need to be able to remember this. Thanks
@eddietorres9208 Жыл бұрын
Your awesome!! Thanks so much 🎉
@RisksAnalyst695 жыл бұрын
this helped a lot, thank you
@rogergoncalves19847 жыл бұрын
That's great! I'd would like to ask a question If I may. How many 1% of the OEE would represent in production volume more or less? Thank you Joek! Roger,
@TIGREinVOLO Жыл бұрын
thanks for making this so simple
@jawadbokhari17 жыл бұрын
If OEE is low for example 70%, do we need to run the plant for longer to get the same throughout put if OEE was 100%. In case of 70%, should we run the plant for existing run time/0.7 to get the desired throughput?
@bondbreaker30967 жыл бұрын
awesome
@MegaBegins6 жыл бұрын
Hello. How do you calculate an ideal cycle time when the machine that you are measuring has to be operated by a human? Do I need to include an allowance for tiredness? How your performance will behave? Woould it be normal and correct to see perfomance higer than 100%, cause operator in some hours may not be tired? Can we consider the stoppage of equipment as a relief for operator fatigue? Hope you or anybody can aswer my questions.
@ThejanaMunasinghe2 жыл бұрын
Thank You!
@kateihle85998 жыл бұрын
Thank you!
@pawanjaiswal33794 жыл бұрын
Sach a great method
@engaredwan8 жыл бұрын
Could be simpler (855/2.6)/480 = same thing always used for cross-check
@betechnical58356 жыл бұрын
Can u make this vid again with Close-up
@polversonrobotics25956 жыл бұрын
Thanks for the video, and making is understandable. I have a problem with Good, Rejects and total pieces. To me the Total is Good + Rejects. Someone had to make the rejects too, right? In your calculations your total is the same with Good. How can that be?
@mbhoniwitness915
2 жыл бұрын
that calculation is wrong because of that ...i agree with you
@77023067597 жыл бұрын
Hello what are the steps which we need to follow if the oee calculated is below 85%
@Vijaysmdn2 жыл бұрын
How to calculate ideal run rate?
@petrsindelar15967 жыл бұрын
Is this really OEE? I think that this is TEEP. For OEE you should callcullate the "Planned op. time" = 480 - 15 - 15 - 30 (planned down times) = 420
@Lionzvezdara78
7 жыл бұрын
Agree with you
@nisheshrohatgi
5 жыл бұрын
exactly, breaks and lunchtime are planned
@aman68931
5 жыл бұрын
i have a question on which setup time is also mentioned in problem.is the setup time also considered a planned down time???
@HarsHSingH-er6ct
5 жыл бұрын
True
@hdezlester
2 жыл бұрын
This is OOE (overall operations Effectiveness) where the planned op time is the denominator. TEEP is inclusive of all available Time (24hours* 365days). For OEE the denominator should be 420 (480- planned downtime)
@jdeleon38215 жыл бұрын
Should come out to 78.3% OEE
@jigsey.3 жыл бұрын
Can you help me with this please 1. In a typical 7-day period, the planning department of the pizza company programs its "Pizzamatic" machine for 148 hours. It knows that changeovers and set-ups take 8 hours and breakdowns average 4 hours each week. Waiting for ingredients to be delivered usually accounts for 6 hours, during which the machine cannot work. When the machine is running, it averages 87% of its design speed. An inspection has revealed that 2% of the pizzas processed by the machine are not up to the company's quality standard. Calculate the OEE of the "Pizzamatic" machine.
@yitbarekgetahun59113 жыл бұрын
availability value can be divided by 420 not 480 ok
@jawadbokhari17 жыл бұрын
@joek15
@drtonyburns73212 жыл бұрын
OEE is a nonsense number. "OEE is like using our weight times our height times our systolic blood pressure, as a measure of how good looking we are." - Dr Wheeler
Пікірлер: 34
Simple yet helpful, thank you so much for doing this!!!
Simple and easy to follow, thanks for the video.
You maked verry simple in 6 min. THX!
Enjoyed that, I just need to be able to remember this. Thanks
Your awesome!! Thanks so much 🎉
this helped a lot, thank you
That's great! I'd would like to ask a question If I may. How many 1% of the OEE would represent in production volume more or less? Thank you Joek! Roger,
thanks for making this so simple
If OEE is low for example 70%, do we need to run the plant for longer to get the same throughout put if OEE was 100%. In case of 70%, should we run the plant for existing run time/0.7 to get the desired throughput?
awesome
Hello. How do you calculate an ideal cycle time when the machine that you are measuring has to be operated by a human? Do I need to include an allowance for tiredness? How your performance will behave? Woould it be normal and correct to see perfomance higer than 100%, cause operator in some hours may not be tired? Can we consider the stoppage of equipment as a relief for operator fatigue? Hope you or anybody can aswer my questions.
Thank You!
Thank you!
Sach a great method
Could be simpler (855/2.6)/480 = same thing always used for cross-check
Can u make this vid again with Close-up
Thanks for the video, and making is understandable. I have a problem with Good, Rejects and total pieces. To me the Total is Good + Rejects. Someone had to make the rejects too, right? In your calculations your total is the same with Good. How can that be?
@mbhoniwitness915
2 жыл бұрын
that calculation is wrong because of that ...i agree with you
Hello what are the steps which we need to follow if the oee calculated is below 85%
How to calculate ideal run rate?
Is this really OEE? I think that this is TEEP. For OEE you should callcullate the "Planned op. time" = 480 - 15 - 15 - 30 (planned down times) = 420
@Lionzvezdara78
7 жыл бұрын
Agree with you
@nisheshrohatgi
5 жыл бұрын
exactly, breaks and lunchtime are planned
@aman68931
5 жыл бұрын
i have a question on which setup time is also mentioned in problem.is the setup time also considered a planned down time???
@HarsHSingH-er6ct
5 жыл бұрын
True
@hdezlester
2 жыл бұрын
This is OOE (overall operations Effectiveness) where the planned op time is the denominator. TEEP is inclusive of all available Time (24hours* 365days). For OEE the denominator should be 420 (480- planned downtime)
Should come out to 78.3% OEE
Can you help me with this please 1. In a typical 7-day period, the planning department of the pizza company programs its "Pizzamatic" machine for 148 hours. It knows that changeovers and set-ups take 8 hours and breakdowns average 4 hours each week. Waiting for ingredients to be delivered usually accounts for 6 hours, during which the machine cannot work. When the machine is running, it averages 87% of its design speed. An inspection has revealed that 2% of the pizzas processed by the machine are not up to the company's quality standard. Calculate the OEE of the "Pizzamatic" machine.
availability value can be divided by 420 not 480 ok
@joek15
OEE is a nonsense number. "OEE is like using our weight times our height times our systolic blood pressure, as a measure of how good looking we are." - Dr Wheeler