#Nut_and_Bolt_design If you like our video, do subscribe and smash that like button. You can comment your doubt in a comment section for clarity. Thank you.
Жүктеу.....
Пікірлер: 27
@duwatv7901 Жыл бұрын
Very straight forward, thank you somuch!
@javencera Жыл бұрын
Really helpful. Thank you very much for such content.
@knvkrishna5432 Жыл бұрын
Really helpful. Thank you very much for such Bro......
@waspmklen48502 жыл бұрын
Thanks so much.I'm a beginner,and I see it very good
@MrJohnnykhoo88 Жыл бұрын
Thank you Sir, is really helpful.
@infokido291211 ай бұрын
The Best Vedio I ever Found To Understand ❤
@malindasilva48988 ай бұрын
Dear brother, While thanking you for the explanation I would like to point out about a small technical error. When creating the bolt, the helix should union with it and should not subtract. Otherwise the bolt will pass through the nut without any revolve.
@FarhadAli-im9mz3 ай бұрын
Great Sir
@bpanthi9773 жыл бұрын
Thanks for uploading such content. It was really helpful. Keep going! Amazing video. 🔥
@techiebud1829
3 жыл бұрын
You are welcome mitra😍and thanks for encouraging words🤗🤣
@aparnashinygottem3120Ай бұрын
Thank you so much sir its helpful
@keithcanonroma5328 Жыл бұрын
thank you so much sir!!!!!!!!! YOU'RE THE BEST! SHEEEEEEESH
@rameshverrajput1582 Жыл бұрын
👌👌👌👌🙏🏻🙏🏻🙏🏻🙏🏻
@bharatdkl193 жыл бұрын
Hello Frands😂😂 Ramro xa hai video. Keep it up...
@techiebud1829
3 жыл бұрын
I'm thankful for your words frands🤗🤣
@Madbootdestruction2 ай бұрын
Very nice but instead of the circle being the profile of your sweep, can you do this with a triangle for a more realistic looking thread?
@ashoksapkota533 жыл бұрын
Cool
@techiebud1829
3 жыл бұрын
Thanks bro😍
@egwimcollins60152 жыл бұрын
Great
@santhoshkumar-il8rs Жыл бұрын
Useful
@sureshv1464 Жыл бұрын
Nicr
@sooya1329 Жыл бұрын
Everything is fine but when I was doing the helix at 6:22 minutes, instead of going down, the helix goes up after I type 30, what should I do?
@umashankaryadav5439
Жыл бұрын
Use - if thread going wrong side or use cursor for up or down
@schoolofpassion Жыл бұрын
Thanks
@girlforsaken15222 жыл бұрын
Now how you convert it to pdf with the point of views?
Пікірлер: 27
Very straight forward, thank you somuch!
Really helpful. Thank you very much for such content.
Really helpful. Thank you very much for such Bro......
Thanks so much.I'm a beginner,and I see it very good
Thank you Sir, is really helpful.
The Best Vedio I ever Found To Understand ❤
Dear brother, While thanking you for the explanation I would like to point out about a small technical error. When creating the bolt, the helix should union with it and should not subtract. Otherwise the bolt will pass through the nut without any revolve.
Great Sir
Thanks for uploading such content. It was really helpful. Keep going! Amazing video. 🔥
@techiebud1829
3 жыл бұрын
You are welcome mitra😍and thanks for encouraging words🤗🤣
Thank you so much sir its helpful
thank you so much sir!!!!!!!!! YOU'RE THE BEST! SHEEEEEEESH
👌👌👌👌🙏🏻🙏🏻🙏🏻🙏🏻
Hello Frands😂😂 Ramro xa hai video. Keep it up...
@techiebud1829
3 жыл бұрын
I'm thankful for your words frands🤗🤣
Very nice but instead of the circle being the profile of your sweep, can you do this with a triangle for a more realistic looking thread?
Cool
@techiebud1829
3 жыл бұрын
Thanks bro😍
Great
Useful
Nicr
Everything is fine but when I was doing the helix at 6:22 minutes, instead of going down, the helix goes up after I type 30, what should I do?
@umashankaryadav5439
Жыл бұрын
Use - if thread going wrong side or use cursor for up or down
Thanks
Now how you convert it to pdf with the point of views?
@umashankaryadav5439
Жыл бұрын
Use plot
Sir unable to sweep bol rha hai