Dnd also sells extensions for your blinker ooooor you could get rid of the deep dish wheel & go shallow🤙

@ModdingAddiction

2 жыл бұрын

Heck no I love the deep dish and I will live without taking the wheel out in the daily. If this was a real race car then it would be a different story.

Did you find out how to remove the airbag

what kind of quick release setup should i run on a 2008 subaru legacy? i dont know what else to buy

@ModdingAddiction

2 жыл бұрын

That is up to you what style you want to go with. I went with an NRG quick release with carbon but ultimately took it off. I didn't like how far it pushed the wheel out for the daily driver. The pedals and buttons were too far and the wheel was too close. It is sitting in the garage and i just mounted the wheel to the adapter and fixed it all. Well everything but the buttons. I MISS MY BUTTONS

Anyone know how to properly connect the horn? I’m using the NRG short hub, nrg quick release and a Vertex steering wheel. Thanks in advance. I tried connecting it but I either get constant horn when the negative of the battery is connected or no horn. I tried sending the ground of the quick release to the 3rd pin like mentioned in the vid and the yellow of the quick release to the 2nd. That gave me constant horn. Then I switched em and got nothing. I only get the constant horn when everything is fully assembled but not if I leave the quick release “dangling”. Idk what I’m doin wrong.

@gorillagrips27

4 ай бұрын

I might have what you’re looking for on my channel

I'm having an issue were trying to plug in the resistors that came with the wheel to bypass the airbag light.. i've plugged them into the airbag plugs (multiple ways) and the light is still on.. its not busted or anything, the resistors look like new... am i installing it wrong? Do the 2 resistors inter-twine with both plugs or is it 1 resistor for each plug? Thx

@nastynautical4599

Жыл бұрын

Bro I’m having the same issue. How’d u fix it

@phiillzzz807

Жыл бұрын

@@nastynautical4599 i goddamn actually fixed it. You have to buy resistors, 3ohm 1watt carbon resitor. It has to be carbon material for some reason or else it will not work. If you have any electronic store around you check it out otherwise check on ebay or amazon i know they sell them there. It took a few dozen packs of resistor types but i finally found which ones work

@nastynautical4599

Жыл бұрын

@@phiillzzz807 well my nrg hub came with resistors. So the ones that come in the kit are the wrong ones?

@phiillzzz807

Жыл бұрын

@@nastynautical4599 they ones that came with mine didnt work, so i tried my friends resistors from another brand steering wheel and still didnt work. I guess subarus are picky with their electronics. You can get either 2.7ohm or 4.2ohm try not to get any more or less than those values. Has to be 1watt and especially carbon film. Tried it with other materials and carbon is best. Just trim them a bit, shape them into a "U" shape and stick each end in the airbag plugs. Put some eletrical tape around as to avoid contact and short something out.

@phiillzzz807

Жыл бұрын

@@nastynautical4599 im not sure if they are the wrong ones, they are the same as my buddys wheel resistor. They worked on his civic but not on my subby. Try out the resistors. If you need a link i have one but its from canada

I wouldn’t like not being able to reach the blinker :/

@williamfabricioo

3 жыл бұрын

You can buy smaller hubs has it sit closer . But you get used to it fast

Any ABS or Trac lights?

@ModdingAddiction

3 жыл бұрын

Yep I busted my clocking spring and it took me 2 new ones to get one to work. Didn’t need the scan tool to fix it just slapped the new one in that actually worked and it was fine

@braylonking-randall4309

3 жыл бұрын

@@ModdingAddiction ahhh ok I'm to point point where I'm just going to pull the lights for the ABS and Trac 🤣🤣

@phiillzzz807

2 жыл бұрын

@@braylonking-randall4309 mine showed up after installing my wheel.. after hours of fiddeling and messing with the computer, the clock spring had turned 180° when i removed the oem wheel and wiring... turned that sucker upside down and boom.. no more abs and traction light on (and for some reason it deactivated hill climb assist lmao)