I’m a diy guy, not a mechanic. This is excellent advice. For us diy guys I would add: “Don’t take it apart unless you know how to put it back together.” I tell myself, “I’ll remember this.” But then I don’t and it takes forever to figure out. Simple tip: take pictures at each stage of disassembly. Did this just yesterday rebuilding the mower deck on my riding mower. While replacing the drive spindles I decided to remove everything to clean rusty spots and rust proof. The orientation of the springs and brake brackets are not obvious. Fortunately. I took pictures of several stages of disassembly - it really helped!

@WrenchingWithKenny

Ай бұрын

Great tech tip about taking pictures as you go. Thanks for your comment and for watching the channel. Keep wrenching 🔧

@chiil034

15 күн бұрын

Plastic baggies and a sharpie are your friend. When I tackle large projects, I tackle the order and throw the screws/bolts, clips, etc. in numbered baggies.

@jskillet8912

14 күн бұрын

Ten years in autobody disassembling and reassembling all my own work and can confirm, more than a week and i forget if I havnt worked on a million of them. Take pictures and separate your bolts and MARK THEM .

@joey9511

10 күн бұрын

Taking stuff apart without knowing how to put it back together is what made me become a mechanic 😂

@louiscolborn6715

9 күн бұрын

Cameras wasn't so available then as today. but I used to take notes and put parts in separate containers in order.

As a long-time mechanic I remember a story a local farmer told me. His adopted son decided to change the oil in their family van. After he did that he realized there wasn't any oil to refill so he drove it to town for oil. He didn't make it a mile down the road before it seized. His father, I'm sure, questioned why that boy was in the family. When he told me the story he got mad all over again.

@robertmaybeth3434

Жыл бұрын

why didnt the moron just put the old oil back in again....D'oh

@bunning63

Жыл бұрын

Brother-in-law years back changed the oil on their new car. Family goes on holiday, transmission starts to make noise, garage diagnosis is no oil in box. Sister questions husband who comments that he did wondered why he couldn't add much oil to the engine after he 'drained' it. He was an officer in the army, transport core... It was decided DIY was no longer in his future. His son, in the Police force, refueled the diesel ute with petrol. Didn't know it made a difference. Genetics. They had no idea what was said about them behind their backs.

@darrellepickering8433

Жыл бұрын

When I felt I had 'graduated' to work in a car dealership I started out with servicing. Now I had working on anything that would roll by that time & I 'graduated' to mechanic. The guy that took over my old job was maybe not the roundest marble in the bag but I showed him what to do, what to look for, etc. All went fine for a week till he changed oil on the lift. For some reason he always left it up, climbed up a ladder & presumably checked for leaks. True or not couldn't tell you as I was in another section. When started it sprayed oil from 6' to the floor. He missed the extra oil filter gasket stuck to the adapter. There were several new cars plus customer's cars in the area all sprayed with oil. He was fired on the spot & I quit when I was told to clean it all up.

@padraicnolan4591

Жыл бұрын

@@bunning63 j

@thewholls7176

Жыл бұрын

I went to change the differential oil in my LSD V8 Ford here in Australia long story short. I drained it and the fill plug is a 1 inch and 1/16th imperial size - or something weird like that which I didn’t have so I just tried to get the fill bolt plug off with the nearest size and rounded it off and I was stuck on a Sunday……. Rookie error. Definitely a good advice to fully investigate the fill situation before you drain anything ……

when i was 17 i decided to change the oil in my 80's model chevy pickup. i drained the oil and swapped the filter, i opened the hooks and started dumping oil into the filler port. after I got close to the amount that should be in the motor, I pulled the dipstick and couldn't get any oil on the stick, walked around the other side of the truck I found my oil running all down the driveway and down the gutter and it made an absolute mess that took FOREVER to clean up. I never had a problem remembering to replace the drain plug after that.

@WrenchingWithKenny

4 ай бұрын

😳 that must have been crazy! Thanks for sharing your story. Keep wrenching 🔧

@allseeingotto2912

4 ай бұрын

I did that on a motorcycle

@armyfazer1410

4 ай бұрын

Me and a friend did that on his truck in high school. Fortunately, it was in HIS driveway! LOL

@YTInnovativeSolution

3 ай бұрын

Don't forget to check for the o-ring when removing the old filter. If it is left on the vehicle, the new filter and included o-ring won't stop the mess once the engine starts. This won't happen to me again.

@jonkirkwood469

3 ай бұрын

I got to yakking with my father-in-law once, and put a quart of Mobil 1 in the driveway, back when Mobil 1 was about 10X the cost of dino oil. It left me a quart low, too.

I was always taught to break the fill plug first, BEFORE the drain plug. Saves many headaches.

@samholdsworth420

4 ай бұрын

Pro tip lol

@seymourbutts3716

4 ай бұрын

Amen, hard lesson learned for amateurs

@allseeingotto2912

4 ай бұрын

To vent

@soilmanted

4 ай бұрын

Absolutely. Aside from the obvious logic of "find out first" if you can get the fill plug out, and thus be able to fill the thing, _before_ you decide to let the fluid out - having the fill plug out enables the fluid to drain out faster and more completely - because air keeps replacing the fluid that has drains, and thus you don't have a vacuum developing that slows the fluid from draining. At the same time, if you want to temporarily reduce the speed at which the fluid drains, in order to reduce splashing and mess-creation, you can put the fill plug back in or partially back in, or simply hold your hand over the fill hole, or use any method you can come up to partially block the fill-hole.

@upnywhiteb

4 ай бұрын

You beat me to it, I did the same thing. At least I did before I stopped doing my own oil changes. I always thought it had to be able to drain better if the other end was open.

Another reason to open the hood first is to check the oil level before draining. This can give a heads up on oil consumption or possible leaks.

@gunsofsteele

Жыл бұрын

Another reason to raise the hood is to check for your neighbors cat 🐈

@FerrickOxhide

Жыл бұрын

Had a customer car with a recurring misfire code on #3. The cats would fail every 6 to 8 months. Regular servicing revealed consistent high oil consumption (checking level before draining oil). No external leaks and It always ran great on all 4 cylinders, tho. I told her to get rid of it, or she was looking at engine work.

@betterthandeadohyea4500

Жыл бұрын

​@@FerrickOxhide Ford engine?

@FerrickOxhide

Жыл бұрын

@@betterthandeadohyea4500 VW Golf.

@GilmerJohn

Жыл бұрын

@@gunsofsteele -- Why bother? It's just a cat.

Being a retired mech, he is dead on. Better learn from a master than by bad experience. Cheaper too.

Valvoline peon here. I feel like the guy that designed our procedures watched this exact video, because that's exactly how I was trained. We need more people like you, giving these simple nuggets of advice out to the world!

@JayAR_YT

Жыл бұрын

Mr.Valvoline man, do you think I should pour junk oil into my engine to help the old oil drain more completly? Me and my dad were argueing when I changed my oil in my dirty old 4th gen camaro.

@JBlooey

Жыл бұрын

@@JayAR_YT Probably not. As long as the vehicle is on a level surface, gravity should do the job well enough, and the occasional engine flush should keep things clean as long as you haven't let too much sludge build up over the years, preventing worn seals from leaking.

@JayAR_YT

Жыл бұрын

@@JBlooey Sometimes ill change the oil in like 700 miles as soon as its discolored, I fell like that does a better job than maybe harming your engine with a oil flush.

@JBlooey

Жыл бұрын

@@JayAR_YT Sounds like you're more into preventing unnecessary damage than the average bear! 700 miles is a pretty low frequency, but if you can spend a little more changing your oil that often, you'll definitely save yourself from the thousands it would cost to repair/replace an engine. Good on ya, man!

@JayAR_YT

Жыл бұрын

@@JBlooey Well the LS1 with 67.000 on the clock does enjoy a random early oil change once or twice a year. It does have a LSX 454 cam, some lifters, valve springs trunions, (you can actually port a stock oil pump so now I get roughly 75lb of oil pressure)I run 10W40 instead of 5w30 too, and has full exhaust. Oh and a BBK intake. I think im going to sell the full drive train and buy a 6.0 LQ9 and some 799 heads, take my intake and oil pump too.

It's nice to see a fellow older mechanic spreading some knowledge that took years for him to learn ..you are doing a great service to many sir..

@tomrogers9467

5 ай бұрын

As a retired mechanic I wish UTube had been around when I was learning the trade. Unfortunately I never had the privilege of working with experienced mechanics to learn from. All my lessons were learned the hard way. I spent the last 20 years teaching young mechanic trainees everything I had learned. At least they got a head start.

@Steve-O_FPV

4 ай бұрын

Took years to learn? That's just common sense. Work through the entire job on a KZread video and in your head before you do it and always make sure you can open something before you empty it. I always pull the cap and the dipstick before I ever jack the car up for oil.

Great advice, 47 years farming and I’ve learned the hard way too often! A second piece of advice is have the filter before starting! (Dam , I was sure I had bought 2)

@oldtimefarmboy617

Жыл бұрын

My father's tractors oil filters are installed horizontal. They have a drain plug towards the bottom of the mounting base. He had the local supplier build him short lengths of hydraulic hoses with a male fitting on one end and a female fitting on the other end. He then screwed the hose into the drain hose on the base and a plug on the other end. That way when he changes the oil he can take the plug out of the hose and stick it into the drain bucket and drain the oil out of the filter while the oil is draining out of the pan. By the time he gets the new filter and fills a couple of jugs out of the oil storage tank, everything is drained and then he can change the filter without getting a lot of oil over everything, put the drain plugs back in and fill the engine with oil.

@AJ-qn6gd

Жыл бұрын

Hopefully the correct filter, nothing worse than draining the oil and removing the old filter and then finding out you have the wrong filter and you don’t have another vehicle to hand to go and change the filter 😡😡😡🇬🇧

@cjbecker1683

Жыл бұрын

@@oldtimefarmboy617 Engineers that designed filters to go on sideways I'm sure have earned many cuss words over the years.........growing up with a small block Chevy in my first car life was so simple "back then" 😉

@ChiTownGuerrilla

Жыл бұрын

One time Oreilys gave me a filter for a V6 when I have a 5.7l v8. Called them and they brought me the right one and swapped it out free of charge. Although they're only less then 5 minutes away it saved me a trip.

@AJ-qn6gd

Жыл бұрын

@@ChiTownGuerrilla 👍🏻😀

I've had many troubleshooting classes over the last decades in my job as production supervisor. The best advice ever, applies in all situations including these. "Don't be like Barney, be like Andy." In other words, BEFORE you do anything, step back, take a breath and look at the whole situation of what you need to do. Invest a few minutes just like a chess game and think about what the next few steps would be AFTER taking the first one. DURING the oil change, look at everything. One time - when I was much younger - I removed the old oil filter and didn't notice that the gasket did not come off the engine with the oil filter. I installed the new oil filter on top of the old gasket and ended up with a leak. Fortunately, I caught it in time and no harm was done. I had been in a hurry and just ASSUMED that nothing would go wrong. MURPHY'S LAW is always present. Get your tools, fluids, parts and everything else staged and ready BEFORE you start the job. It's a shame that these lessons have to be taught but it is great that videos like this one are around to protect those of us who haven't learned yet. Thank you for a great video!

@anthonyjulson8840

Жыл бұрын

I did that ONCE with the oil filter on an old Ford. I always check for leaks when I finish an oil change. It had dumped 1 qt before I realized I had double sealed the filter. Now I ALWAYS look for that old gasket.

@stefanpuszka2835

Жыл бұрын

Everybody is human and we have to learn its good to have someone experienced to teach us.

@melvinrichardson4501

Жыл бұрын

I always take a minute to say to myself, " what will happen if it do this." On everything i do...

@AR-mb3id

Жыл бұрын

I doubled the oil filter gasket and ended up with a seized engine when all the oil spilled out the first 15 minutes of a family trip. I've done hundreds of oil changes and always check and wipe down the surface, but this time I was in a rush. Lesson learned. Always check and wipe it down before inserting the new filter.

@Colorado_Native

Жыл бұрын

We had a rule in the Air Force, the 6 Ps, Proper Planning Prevents Pis Poor Performance. It works pretty good.

Yup. You & Eric the car guy are the only mechanics I've heard mention this. It's something u learn from a bad experience & then never forget it again. Then you spread the knowledge so that someone doesn't have to learn it the same way u did! Thank u

@WrenchingWithKenny

Жыл бұрын

Thanks for watching !!

@shadetreec6013

Жыл бұрын

Yeah, I learned the hard way and will never forget.

@WarriorsPhoto

Жыл бұрын

I've broken stuff other than knuckles working on cars. Yes it is frustrating and you will have an upset 😠 customer. 😢

@yt-user03561

Жыл бұрын

I mean you could potentially apply the same logic to just about any job you're about to do. Expect that things wont go you're way and be prepared to find a way to get it done or refuse it.

That was a golden nugget of auto advice!!

excellent advice. I always remove the fill plug before draining, just to make sure I know where it is, and, that I can actually remove it.

@fjb4932

3 ай бұрын

This is EXACTLY what this YT was about... ☆

This man speaks the truth right there. Not sure why or when I learned to do that first but I do and it paid off not long ago when I was changing fluids in a running 74 C10 pickup that I bought as a project. The fill plug in the rear-end wouldn't budge even with a breaker bar. Had to use an impact and sacrifice an extension to get it out.

@WrenchingWithKenny

2 жыл бұрын

At least you got it !!

@oldtimefarmboy617

Жыл бұрын

Just for your information. Those plugs used tapered square holes just like all pipe fittings use tapered threads. They do make adapters for regular ratchet drives that are tapered and solid just for use in those type of plugs. That way you get the maximum contact with the surface of the square hole and no weak point because it does not have a hole in it for a socket detente. You can save a lot of tools using that by not breaking the square drive on a ratchet, breaker bar, or extension. If they have a square knob rather than a hole, those are tapered as well and they make a tapered square socket for them.

@paulhighbarger3356

Жыл бұрын

Heat very often breaks a seized or tight plug out, especially if Locktite on threads. Torch a little....not too much.

@ericl2969

Жыл бұрын

@@oldtimefarmboy617 I never knew that! Most people never change the oil in a rear (or front) differential but I've done it a bunch of times on a bunch of different vehicles, and it always seemed strange to me how the square end of a socket extension didn't seem to fit all that well (though on my old Subaru, the square end of an extension would fit perfectly, so I guess they had mechanics in mind when they chose the style of drain plug). As to a square "knob" on such a plug being tapered, I guess I have noticed that on large-size pipe plugs, but when I've installed drain plugs on items that did not come with one from the factory (transmission pans and rear differentials of American trucks), the pipe-threaded plugs with square "knobs" that I bought for that purpose were square and non-tapered, and fit a wrench perfectly. I'm not sure why they ended up being that way, but I guess it's a good thing.

@Maxx134a

4 күн бұрын

I had similar situation and used a car jack to lift & turn the wrench to loosen the bolt!

Great point! As a non-mechanic… I would never think about it

I covered this with my students just the other day. I've always done it this way and nobody taught me, so glad to see it's general mechanical knowledge! Great video! Hopefully it saves someone a few headaches 😁

The voice of experience. My father was an auto mechanic and taught me similar things.

I'm a newer guy and this is valuable info. I appreciate you sharing it.

100% correct...As an add-on...open your hood if you are doing any work underneath the vehicle...added light and won't have to lower the car (or worst) crawl out from underneath to open it...

Great advise for the newbie, also open the window before you get out and close the door, so that an aftermarket alarm won’t lock the doors with the keys in the ignition, LOL.

I love that you teach something that you'd usually only learn with experience. Most YT mechanics jump over this little stuff.

Short, and to the point. Thanks for keeping it short yet informative.

Yes one of those things that’s so obvious that you never think it until you experience it, then will never forget not too. I wish I was told this back when first first starting. I learned the hard way and I’ve seen experienced techs do it too. Awesome for you to share this, you saved many from heartache for sure!

I was taught exactly this over 30 years ago, and to this day i pop the hood and put the cap on the latch first. Being a great tech requires a good deal of common sense .

@GT-mn3bx

Жыл бұрын

Why would you put the cap on the filthy latch?

@bullitthead7853

Жыл бұрын

@@GT-mn3bx So you don't accidentally shut the hood without having filled the engine with oil. Seems like that would never happen, but you'd be surprised at the distractions that occur in a busy shop. This is just a measure of safety. Also, latches generally aren't very dirty relative to other places under the hood and if you set the cap upside down, it doesn't even matter anyway.

@ericbruck7958

13 күн бұрын

What is common sense? Common sense is learned! You did not know how to tie your shoes, your mom taught you.

Thanks for a good hint. I hadn't really thought about not being able to fill something before draining it, because I've never run into that problem myself, but I see the point and will keep that in mind in the future.

100% spot on! Here in the rust belt there is a long list of reasons to be sure something can be refilled prior to draining.

Prep is everything. That's why if you watch those cooking shows they have those teeny little cups that you stick in the salt, pepper, curry, minced onions, whatever they're gonna use in the recipe, *before* they even turn on the stove. This way, you not only measure out exactly how much you need, in advance, but make sure you even *have* the ingredient in the first place before you start. And no rushing to measure out a teaspoon of this or half-cup of that, before the whatsit in the pan burns, etc.

@thegreat9481

Жыл бұрын

Don’t agree with that cooking comparison. Sometimes you just know how much seasoning to put with experience.

@gabrielfraser2109

Жыл бұрын

In professional cooking, that's called Mise-en-place. You don't start cooking until you have everything you need in front of you.

@aries6776

Жыл бұрын

lol I do this after watching a lot of cooking shows and initially thinking it was just for visual effect but in reality it really saves you time. I get all the ingredients out on my kitchen table and then find I am missing something! I do the same for any jobs I do on my car. I lay out all my tools and parts ready for the job.

@stephenc3060

2 ай бұрын

@@thegreat9481 Spoken like a true amateur chef. If you order the braised veal shanks with gremolata and risotto Milanese from your favorite burger stand every weekend, and it's always different because the kids on the line think they "just know from experience" how much of what goes in, then the sous chef isn't doing their job, the executive chef is looking incompetent, the investors are losing money, and everyone's income source is in jeopardy. Mise en place. Everything ready and in the right spot.

@thegreat9481

2 ай бұрын

@@stephenc3060 Man go somewhere with that nonsense 😂

Excellent points. I've worked on my own cars all my life and have never confronted this problem, but it's certainly a good precaution to take on any car.

Excellent advice, personally I have checklists when I work on my car, I do not skip steps and that has saved me so many headaches.

Been working on and taking cars and trucks apart for at least 50 yrs never thought about this and he's right maybe because I never ran into the problem with filling anything have taking things apart but for what it's worth thanks for the info

I'm not a mechanic but I've been wrenching on my own cars for 40 plus years. This knowledge is golden. I've never really ever thought about this but I guess it's never to late to teach an old dog a new trick. Thank you Mr. Kenny!!!

Good advice. Although it makes sense to have the hood open anyway for oil changes as I tend to check the oil level and condition before an oil change to see if there are any other issues to be wary of. Also removing the filler should allow the oil to drain more easily. Finally, an open hood allows more light in to see things like the oil filter which is often removed from above too.

@GT-mn3bx

Жыл бұрын

Why weren't you checking the oil at least weekly to begin with?

@daveshongkongchinachannel

Жыл бұрын

@@GT-mn3bx I do that too anyway but I specifically take note of the level before an oil change to look for signs of increased oil consumption.

@wingkinwong9082

Жыл бұрын

​@@GT-mn3bx Here it is recommended to check the oil level monthly or at every fuel refill.

@tomrogers9467

5 ай бұрын

Neither of my Hondas burn a drop between changes. But I still check regularly.

This is the best, practical advice video I've seen on YT this week. Thanks, Kenny. In the 80s, 1960s, and 70s Mercedes Benzs were notorious for the hood issue.

This why I do my own fluid changes... others I paid have damaged my vehicles, over tightened or used cheapest coolants/lubricants.

In my younger days I used to always do my own oil changes and never ran across this problem, BUT It's some pretty good advice to heed. I never thought of it and thank goodness I didn't have to learn the hard way!!

@oldmanfromoc7684

Жыл бұрын

I changed oil in cars and big trucks never had this problem!

@markevans4547

Жыл бұрын

​@@oldmanfromoc7684 I guess you should be proud of how lucky you are

@tomrogers9467

5 ай бұрын

My only problem was a defective FRAM filter that blocked the outlet and pumped my oil change onto the floor. Always check the filter for leaks after starting. Could have blown the engine if I hadn’t!

Good, real world, advice. I like where you store your fill cap during the oil change, it almost guarantees that you can't close the hood without noticing you haven't filled the engine with oil. One thing I like to tell new techs is to get into the habit of doing a visual scan under the hood including: cowl, fenders and radiator core support areas before closing the hood after service. It seems like common sense but it's surprising how often it's overlooked, and things are forgotten.

@reformedchinesecommunist

Жыл бұрын

I work in a power plant and there are so many things that this logic applies too. There is a ton of procedures that MUST be absolutely followed or a bunch of millions of dollars of equipment will nuke itself in minutes if not a literal minute. Plus it’s fairly high consequence financially, PR wise if we go down. Etc. If you forget to open that one valve you can blow up stuff lol. After years working with steam and high pressure stuff you become a bit OCD, and I try to teach it to newer people too but many times kids just dont have that awareness of “i make a innocent thoughtless mistake, HUGE consequences WILL occur.” They are not typically ready for the stress lol

@aries6776

Жыл бұрын

I drove home from getting a tyre repaired. There was an odd loud ticking noise coming from the rear wheel. I pulled over and found the shop had not cut off the tyre repair stem which still had a bit of metal stem in place which was bangiing againt my wheel arch. The same shop also had to pay for a replacement undertray because they didn't replace mine. I even found a spare part when the manager told me he couldn't find a replacement. I'm too nice.

I learned this as a teenager on an old '65 C-10. Was going to change the 90w in the 3 spd tranny. Drained it all out and went to remove the fill plug. Froze solid in the side of the case. I ended up twisted the square head off and having to pull the transmission and take it to a machine shop to have the fill plug drilled out and tapped. It probably would have been better to just get another transmission out of the junkyard. Another expensive lesson in the hard knock school of mechanics.

@oldbiker9739

Жыл бұрын

Willy , I bet you wished you still had that truck so easy to work on and a great truck it was .

@willymccoy3427

Жыл бұрын

@@oldbiker9739 It was so rusty that the cab would shift around on top of the frame going down the road. I ended up using it as a parts truck for another 65 C-10.

@ostrich67

Жыл бұрын

You had it off, you could have refilled it through the drain plug at that point.

This is actually a good life lesson. Always be thinking at least one step ahead.

Good points. I never leave an oil cap off, in case something falls into the open hole. Also never leave tools in an engine compartment. A& P tech for over 30 yrs.

Kenny you are an absolute brilliant mechanic I wish you were in my area you'd get my business my master mechanic has retired and he's going to be difficult to replace but surely I can find another very good mechanic I'm getting to old to do the hard jobs myself thank goodness for people like you God bless your a good man keep up the great honest work my friend

@GT-mn3bx

Жыл бұрын

Lol. He literally set the clean side of fill cap on the dirtiest part of any vehicle.

Great advice. I never thought of making sure I can refill first. Also never shut your engine down in a dangerous or remote place or at night or in any place you are stopping for a short time. Think about places you would not want to break down and don’t shut it off!

@WarriorsPhoto

Жыл бұрын

I've helped someone out of that jam before. Bummer too. 😢

@rubiconklbrutorowman7577

Жыл бұрын

Well done, the MOST critical safety tool is get your car ready to take off when U sense spooky ahols, beach, inviting U to sort of quick send to rob U n the rest JUST like horror movies, but the BEST practical safety measure is let someone know U are forced to stop or go through the road, which you should avoid in the first place and NO night time, but if you are forced to stop at night time plan passing through the remote road at day time N spend Ur evening at well lid shopping center, even gas stations, safe one, restaurants, any open 24-hour stores, even 7-Eleven where people are round, often they are one of the deterrent to would be criminals to avoid people...

@tomrogers9467

5 ай бұрын

Your standard hollywood horror movie theme! The film “Grand Canyon” in the 90’s was based on a breakdown in the “hood”.

@TheAnantaSesa

4 ай бұрын

Also don't walk far from an idling vehicle if you don't want it stolen. Unless you have a spare key to lock the door while it's running.

When I was 15 and knew everything I would have sneered at this for being TOO simple. Now I think the reason simple things are rarely taught is because schools and colleges must always at least give the impression that any knowledge is difficult.

@chrislittle7285

Жыл бұрын

When I was younger so much younger than today 🎵

@willpeony5534

Жыл бұрын

@@chrislittle7285 Flying over, I thought he was in trouble but that man on the desert island had spelled out HELF

really great advice. This is why it really important to value and learn from the long experience of others, so you don't end up learning the hard way after a mistake! I have yet to come across simple, yet such practical advice in other youtube videos aimed at beginner car enthusiasts!

Outstanding advice Kenny. Stuff so simple it is often overlooked. AND, it's so important. Thanks for putting that out there.

@DEFENDERNZ

Жыл бұрын

What's wrong with refilling through the drain hole with the right fitting? Just a thought.

@donaldshimkus539

Жыл бұрын

​@@DEFENDERNZ the right fitting would most likely need an integral check valve to prevent it from draining again, AND you will need a way of checking the fluid level so as not to over/under fill the unit. UNLESS you know the exact amount to refill it with. Hope that helps a little.

@DEFENDERNZ

Жыл бұрын

@@donaldshimkus539 is it that hard to find capacity? I think not. As drain plugs are extremely accessible, I'm sure a half decent mechanic could pull out a rubber bung and thread in the correct bung and only lose a minute amount, accounting for that in the amount you put in. Like I said, just a thought.

@donaldshimkus539

Жыл бұрын

@@DEFENDERNZ that's also a good point although not all drain plugs are rubber(very few in fact). Most are threaded metal plugs, requiring a little more time to remove and install.

@speedlever

Жыл бұрын

@@DEFENDERNZ In the particular case of the vehicle in the video, you put fluid in until it runs out the fill hole. Not sure how you would get the proper amount in via the drain hole.

I've worked on a lot of things with wheels for most of my life and now fifty years old now. This is good info that I never honestly thought of. I do not do auto mechanics for a living though

I had this happen with my 2004 GTO, hood latch didn’t work, heart sank. Eventually got a bright or to put pressure on the hood while I jiggled the hood cable with vise grips. Solid advice.

That was great advice that should never be forgotten. And used in all aspects of every day life.

Thank you Kenny for all of your videos, extremely helpful and informative.

As a husband and father of teenage boys it’s not often that I feel smart but thanks to Kenny we’ve achieved that rare mark. I’ve always done this just out of common sense.

@rpm2dayg648

Жыл бұрын

Man, you sure said a mouthful there! They know it all until much later in life.

The best advice I was ever given regarding differentials, luckily not just from your video but throughout my life. Make sure you can open the Fill/Level plug before opening the drain plug!

My motorcycle mechanic talks to me this way while he works on my bike. Hes so proud of his work which is A++ in my book.

As a one-time U-Haul mechanic, and as a one-time bike shop service manager, I loved finding little mnemonics to help me with the mental checklists. The oil cap on the hood latch is exactly the sort of thing I like doing.

@duckwacker8720

Жыл бұрын

Until you forget it and break it.

@durk541

Жыл бұрын

​@@duckwacker8720isn't that the point? To break the cap instead of running engine without oil

@ai53224

4 ай бұрын

I cringed at setting the oil cap down on the DIRTY latch. I just HOPE he wiped the cap off before reinstalling. I drove company cars for many years and that was a very common quicky lube place mistake.

When I first started wrenching I started out as a tire, & lube tech. One of the best pieces of advice I received was to always put the oil cap on the hood latch so that you can't close the hood until the oil has been refilled. I tell people to do it that way all the time because in the last 20 years I can't tell you how many times I've seen a vehicle get returned to the customer without any oil. Nobody thinks they will make that mistake. But I personally have broken 2 oil caps because I went to close the hood and it was still on the latch where I put it. But instead of having to pay for an engine, and install it for free I just had to buy an oil cap. We all get busy, and in a hurry and things will get overlooked sometimes.

This is excellent advice. Just the other day I was changing the oil in my 96 Crown Victoria. I opened the hood, removed the fill cap, broke the drain plug loose and drained all the oil, removed and change the filter. Everything was going as planned until I went to pull the dipstick, which broke below the flange and left the oil guage about 2 inches below the dipstick tube housing. Turned a 20 minute oil change into a two hour oil change. Pull your dipsticks too!

@WrenchingWithKenny

10 күн бұрын

Great tech tip! Thanks for sharing. I love Crown Vics!! Keep wrenching 🔧

If you had limited choices you can always screw a fitting in the drain and pump it in from there. In marine service it's done quite often on different services with a pressure pot or pump bucket. Maybe a little mess but at least you are not stuck

@artlife6210

Жыл бұрын

exactly what I was thinking, a bit messy but quick and almost free lol

@lennythomas7230

Жыл бұрын

My thoughts too. But the pressure needs to be relieved as you're pumping in so you'd really have to come up with a special contraption for that if you can't open the fill.

@artlife6210

Жыл бұрын

@@lennythomas7230 I believe that case has a vent on front top that allows pressure release and has a check valve that keeps external air, or water out.

@boardworker5138

Жыл бұрын

Ok, but how do you know if it's full? On transfer cases like that, the instructions tend to be "fill until it comes out the fill hole".

@plap.

Жыл бұрын

@@boardworker5138 there is a known volume listed in the Manuel or measure what you took out

The cap trick is good. I always put the new parts someplace, like the drivers seat as a reminder that they have not been installed (we all get interrupted)

Not only is this a father advice he'd tell his son for how to run the business, its also straight to the point no BS here or there, even the subscribe reminder isn't annoying and its pretty short. No begging no flashy unnecessary moves.. you got a subscriber for that

Randomly came across this video but what a great lesson to learn. Thank you.

@WrenchingWithKenny

3 ай бұрын

Thank you for watching and commenting!! I appreciate it!!

Good video. Saw another comment about checking the fluid level before draining, which can tell you about leaks or consumption - an excellent point. Here's what I'd add: you can drive a car for a few more miles if it has old oil in it, but you cannot drive a car that has no oil in it. Something to keep in mind if you are working on your own car, especially one you use to get to work!

@GT-mn3bx

Жыл бұрын

Why aren't they checking fluids regularly?

I don't recall never being able to get the oil in the vehicle but I had one where I couldn't get it out. I had a GMC Sierra or a Chevy Astro (I don't recall which) where someone had put some sort or non-removable oil drain plug in it. I changed the oil in that van like it was a boat and pumped the oil out with an electric pump through the dip stick tube. Keep the good stuff coming.

@ericl2969

Жыл бұрын

Could it have been a push-valve drain plug? The first time I changed engine oil on an old International truck with a DT 466 engine, I tried everything to unscrew the plug but couldn't do it (you could put a wrench on it and it looked like it should come right out, but it wouldn't budge). It took me about ten minutes to figure out that pushing a spot in the center of the plug opened a spring-loaded internal valve and then the oil poured out just fine. Releasing pressure allowed the spring to close the valve for a leak-free fit. I don't know if the DT engine came from the factory with that setup or if it had been added by the previous owner (that was the only truck of that kind I ever looked at this way). There was really no way for a person not familiar with this style of drain plug to understand how it worked just by looking at it. If it was an add-on feature, maybe that's what was on the car you dealt with.

Thanks man the little stuff can go such long ways!

Great advice. As a "home mechanic" ie. I do my own basic maintenance. Always ensure access to fill and make sure you have enough of the right fluid to refill before you drain. Remove fill plug bolts and put them back in partially, open the hood, etc. Another tip for small engines, if I'm doing an oil change on a mower, snowblower, etc. I'll tag the pull start/power ignition with a "no oil" tag before I even start. Then I'll service the oil. If I somehow get interrupted not refilling the oil won't skip by me.

Great video. Thank you. One can never take these things for granted Thanks for sharing your knowledge with us

Good advice. I'll add my experience, doing an oil change, drained the oil, but after an hour of trying could not get the filter off. Had to put the oil in, go buy a better filter wrench and another 5l oil and start again. Ever since that I make sure I can get a turn on the filter before draining.

10+year automotive mechanic and going on year 4 of heavy diesel and I always pull the fill plug, pop rad cap, open oil fill cap before draining any fluid. 1) like you mentioned and 2) prevents vapor lock and helps to siphon fluid out. Also a nice consistent steady stream until empty, less potential mess.

Great advice, even after 37 years on the spanner’s I always think it’s wise to be reminded about basics, I tell my apprentices this until I’m blue in the face 😂

@adamstrand5126

Жыл бұрын

😊😊😊😊😊😊😊😊😊😊😊😊😊

@GT-mn3bx

Жыл бұрын

Basics like don't set the clean side of drain cap on the dirtiest part of a vehicle at 1:50.

Great advice! Make sure you can do all the steps before you start step 1. (I do small engine repair. Same goes.)

I’ve changed a few and never thought of this. Great practical advice!

I'm glad people talk about this on KZread. I'm a home mechanic. Meaning I do most of my own work. I almost made this mistake one time when going to change the oil in my rear differential. But I stopped to think about it for a second right before I had the drain plug almost all the way out and my logical brain stopped me. And it's a good thing it did because the fill plug was not coming off easily. I ended up taking it to a shop and asked them if I could pay them $20 to throw it on the lift and break it loose because I couldn't get enough torque on it on the ground. I didn't have a torch or an impact gun. They were nice and did it for me.

And don't forget a way to check the oil level. A lot of newer vehicles don't come with transmission dripstick, they just have a cap on the fill tube. You have to service dipstick and info on how high the oil needs to be on it.

You're exactly right cause it's the little things that most usually causes major problems...I myself have came close to messing up cause I'd get in to big of a hurry and came so close of overlooking simple things. I'm the type of person that has to do repairs by myself and I always double check everything especially if it's not my vehicle...I don't know why I've always done it but I always put the oil fill cap in the same spot you just did and it became a habit...Most mechanics won't listen to stuff like this but my ears are always open when it's comes to a vehicle cause it doesn't matter how much hands on and schooling I've had, I still don't know it all and I don't carry myself thataway cause that's usually the one's that eventually messes up lol...

@bullitthead7853

Жыл бұрын

No mechanic knows it all, be wary of the one's that claim they do. One of my automotive service information systems has 30 million pages of service info, I subscribe to three of these services because no single one has all of the information we need, they each have shortcomings, 30 million pages isn't enough. It's just too much information to "know it all."

Very interesting. I have been doing that since 1989 and it's a formula that'll help you all the time. It's good practice to obtain a new engine oil filter before removing the old one.

Love this message man. I always pop the hood, check for a cartridge filter, and loosen it if it has one. Everyone else at my work wants me to just get it in the air and get it started. If I'm on it, I make sure that hood opens, and I don't have a cracked oil filter housing.

Really good advice! Kinda like driving a semi down a long, narrow driveway. Walk it first, to make sure you can turn it around to come out.

@steventrojanowski3595

Жыл бұрын

I have to do this all the time towing tractor trailers… other things like that when towing… do 3-5 mins of work now to avoid an hour of work later.. if it comes to that… which it won’t because you’ll know if you do this 3-5 mins of work beforehand lol

@erik_dk842

3 ай бұрын

A semi driver backed up a quarter mile to my uncle's farm because he thought there wasn't room to turn around there, which there was. Only he didn't make it all the way there, but drove the trailer wheels off the road and got stuck. My uncle's 100HP tractor couldn't get him back on the road, so the driver had to wait an hour for the recovery truck to winch him free

One of the 1st things I do when working on any vehicle, is to pop the hood and check the oil, before starting the engine. Answers 2 questions right there.

Good advice, I got away with that mistake once. I had to replace a leaky rear axle bearing & seal about 7 years ago on my 92 Ford Explorer. Took off the rear diff cover, pulled axles, replaced rear bearings, rear brakes, drums, cylinders... And found that the diff fill on the front was rusted on tight. I didn't try anything drastic to remove it to avoid damaging the differential case, I considered buying an expensive rear differential cover with drain & fill plugs, instead I drilled a hole in the thin rear cover at the same level as the front fill plug, installed cover, filled it, sealed it with a Dorman Rubber Differential Plug for Jeep and some Indian Head gasket seal. It worked fine until I sold it last year! 😅

Something SO basic yet probably so forgotten getting a lot of people in a jam. Thank you for sharing this... a wonderful reminder to use common sense. Liked and subscribed.

Great video. As a back yard mechanic, I never thought of this before.

Great advice from your years of experience. I like the idea of putting the oil cap on the hood latch so you don’t forget to fill the vehicle with oil. Cheers.

@robertmaybeth3434

Жыл бұрын

that or, I often just put the bottles new oil on the driver's seat. But if you're working with somebody else around, even that's not fool proof if you have a fool around.

@elultimo102

Жыл бұрын

There was a backhoe for sale, on which the dealer's mechanic neglected to refill the oil, after previously draining it. He then ran it for 5 minutes, putting a fist-sized hole in the block----Oops. $5800 for a new engine + normally $3000 in labor. (They were trying to sell it as is, for $18K).

@steveclark..

Жыл бұрын

Personally I don't like the idea of leaving the oil cap or say spark plugs out whilst you are working in the engine bay. If something falls in them, a small nut etc, you could have a big problem.

@WindOfTheWisp_Janine

Жыл бұрын

@@steveclark.. Agree...I just loosen the oil cap to allow air in while draining, but don't remove it completely.

Simple but good advice. It's rare but it still happens, you don't want to be the person trying to get a couple quarts through the diff vent because you can't get the fill plug out. Lol

@pujabelgian

Жыл бұрын

Conscientious (honest) knowledgable mechanics are becoming a thing of the past. We drive/maintain a 23 yr old van because we understand it. Get to know your vehicle, no one will care for it like you do. We dropped into a quicklube one time on a road trip. The tech tried to sell us a $129 diff oil service holding up a black oil dipped finger as proof. Our records showed it was changed the yr before. Nice try boys! 😉

@ericl2969

Жыл бұрын

@@pujabelgian You are so right! And here's another thing about that. They probably don't usually have to cheat to make you think the diff oil is dirty because on most vehicles it already is, BUT, when they unscrew that fill plug in a hurry and poke their finger in there without doing any cleanup first, they could easily knock some road dirt into the filler hole, and now the bearings in there are probably on borrowed time. A good mechanic will clean up all around the filler plug before removing it but a quick-lube mechanic would never take that precaution.

Great advice, I've always removed fill plug first, but never thought about not getting the dam hood open.

I'm a new mechanic in training and here in south america we get lower quality cars in general, which means that the oil caps/fill plugs will either seize really badly or if its plastic it will just break. I learned this really early in my career so far because of it and thankfully I've never found myself in a situation like that, but this is golden for people who are just trying to change their own oil for the first or second time

Reverse engineering at it's best! Great point. Good habits save so much time in the long run.

Great video! I learned that the hard way many years ago with an NV3500 that the fill plug was cross threaded and rounded off. The customer didn’t want to pay to fix it properly so we had to fill it through the shifter hole on top. What a nightmare!!

@WrenchingWithKenny

2 жыл бұрын

I had an old Ford truck many years ago that I resealed the rear cover on , went to take the fill out and found the same thing , rounded and seized in place . I wound up welding a Bung to the cover and using that as a fill . Then just placed an oil pan drain plug into the bung ... Worked quite well, but was a total waste of time

Done many an oil change and this is not something I had considered, great advice thanks!

I was lucky enough to read this on a Sweptline forum before draining.my rear diff. I got the fill point open, but not without some time & patience. Never assume that the last guy did anything properly when embarking on a repair or service.

Haven't worked in a car dealership for years, and I always liked to have all my "ducks in a row", as much as possible, when starting any job. People were always trying to rush me blindly into every job, and like this guy I was like no way; no how. Too many times, like him, been blindsided by unforseen problems taught me the hard way.

Another issue that many people have with basic maintenance, is knowing which dipstick is your oil and which is your transmission. Unless your oil hasn’t been changed in years and it’s black then you should know the difference.

@WrenchingWithKenny

Ай бұрын

True! Plus, there are the transmissions that don't have a dipstick at all. Thanks for watching the channel & keep wrenching 🔧

Never ran into this maybe out of luck. But now I have it in my head now. NEVER drain anything until you KNOW this fill plug is accessible AND it OPENS. Thanks for saving me grief!

You automotive mechanics make me chuckle with the stuff you think is difficult.

@rabokarabekian409

5 ай бұрын

Do much mechanic work and you'll find out how much your errors make you chuckle. Ever hear of Murphy and his buddies?

Great point 👍

BEFORE REFILLING: Check that the drain plug is installed properly. Don't ask me how I know - just saying for a friend ! 😂

Great advice usually comes from someone who's learned the hard way. Thanks!!!

The Chevy Vega was terrible about broken hood latch cables. Of course, the hood was hinged in the front of the car, just for fun! That's where I picked up on the make sure you can fill it thing I put the oil fill cap in the latch for many years, before I retired. Great post BTW

One of the smartest things I have ever learned on KZread. Thank you so much for this tip. I know you’re going to be a hero for someone.

In the past, I have given people similar warnings, most blew me off. "Make sure the new part is correct BEFORE you remove the old one." That means that you have the replacement, in your hands before you start the job, so you can verify fit. No, they aren't a pussy, they pry, beat, heat and pry. They mutilate the old part, then they either open the replacement an it is not correct or they go off to the parts store for the replacement part and can't get a proper match. Now what???? Water pumps are a perfect example. With this, without that, early build, late build, with this type compressor, with the other type. Many variations but they DO NOT HAVE YOURS! I never start a job without having known correct replacement parts, on hand. If it's brakes, I want anything else that I may need on hand. If I don't need it I will return it. The last time I trusted being assured that the part was correct, I had to go back for the correct axle shaft. I was going to bring both but made the wrong decision. My sister had to go get it and deliver to me as I did not want to put it together just to go get the correct part that I should have had there already. Never again!

Have always removed the fill first regardless of the issues of finding it/getting to it. Great video and hopefully people just starting out listens

Wow , that’s so simple but I had not thought of it! Some times the simplest things are the most important! Great video.

That is one of those basic things that is so basic, you forget unless you get burned by it. It all comes down to procedure and always follow it. You are so right. Great video!

@WrenchingWithKenny

Жыл бұрын

Thanks for watching 🔧

Do not leave the cap off and possibly allow something into the engine. Also, be sure you can loosen the oil filter, but leaving an old one on isn't the worst thing in the world. Worst case, you refill, drive it somewhere to get it off, and lose your new oil changing it later.

@robertmaybeth3434

Жыл бұрын

...counts as a minor engine flush anyway according to me