People don't realize how lucky they are to have these videos man. Your hours of work and learning all put in a 25min video. 👌🏽

@Gancycle

2 жыл бұрын

I know. I don't watch TV everyday. I watch KZread instead. Isn't it amazing. I purchased a 05 F-350 6.0 with a no start issue when hot. I wanted to learn about diesels. Learned so much already in the first 30 days with KZread. I work on the truck and then watch KZread. Repeat until problem solved. Just keep learning is the best part.

@ronymorales3527

2 жыл бұрын

@@Gancycle that is what I am doing now Trying to learn Ford diesel This videos are the best

@Gancycle

2 жыл бұрын

@@ronymorales3527 Smart move. My 05 F-350 was a trade in that the non Ford dealer didn’t want. So I purchased it for a low price. I drive daily to work now thanks to Ron on KZread. Truck wouldn’t run past 15 minutes. The hot no start. Ended up being the IPR valve. Would not let the engine build 500 psi at an idle. Also replaced seals and dummy plugs. Had the injectors out. Now I know what happens when I turn the key to fire it up. You learn what sounds to listen for like Ron said. Great knowledge.

You make the best videos for Ford lovers that do their own work! Thank you for all you time and effort that you put in and for sharing your knowledge!

Great video! You do such a great job explaining everything in a simple way. Thanks for all your time making these great videos!

Awesome vid!!! Thank you for your time. I just installed my st pic fitting upside down!!! Glad I came across your video.

Excellent been a mechanic for 40+ years diesel is not my forta but have to tell you this video you made is perfect keep it up

@FordTechMakuloco

10 жыл бұрын

Thanks.

Great video man you make it look pretty easy for a person that is mechanically inclined but has never done a powerstroke

Brother, you are a gift to those of us who do our own wrenching... thank you.

Great video. I was too chicken to do this repair myself back in 2012. Watching you do it, it doesn't look too horrible.

If you have an IPR air tester... highly recommend doing a final air test after you get the cover back on. Better to identify any additional leaks now before you reassemble everything. Thanks for the vid.

Another great video, especially on such a touchy area. One thing, you were so careful to insist on using rags while disassembling to ensure nothing fell back into the camshaft, etc, but seemed to not be an issue reassembling. I know it's so easy to not only drop the bolts, but the sockets and adapters when pulling them off. I now use duct tape to hold those assemblies together...just in case.

This made me appreciate working on bmws more. Great vid. Well explained. Now time to get to work.

Great video. Enjoyed the steady camera. Thanks.

Great detailed instructions to the size and type of tools!

I’ve been a mechanic big trucks mostly .Like what someone else commented to have these videos are golden.

Thanks a lot for responding and for the advise. I will try to get a power balance test asap. Thank you.

thanks for the video. the hpop on my 04 6.0 has been giving me a lot of problems, and I really don't have the money to bring it into the shop.

had a crank no start 6.0 yesterday, built 300psi icp. blew the stc fitting out and cracked the rear timing cover first time seeing a cracked cover and bent branch tube.

Ahh very awesome video bro this video is packed with real world of turning wrenches bringing it to people at their fingertips very valuable info .Sure would have been nice to have this video instead of a service manual days

This video helped me a lot! Thanks! Btw: Permatex Grey (not red, blue, or black) is what should be used at the rear engine cover/block union under the HPOP cover. The HPOP cover bolts should be installed finger tight and allowed to sit for 1 hour while the Permatex starts to cure. After one hour has passed then the HPOP cover bolts should be torqued to spec. Cheers!

Nice very thorough vids and work i also work at a ford dealer have been with ford since 2007 been at independents for another 15 years watched a handfull of your vids liked the dps vids thanks for the vids keep um coming

@FordTechMakuloco

10 жыл бұрын

Roger that.

what kind of sealant did you use to put the cover plate back on in 19:30? will permatex work?

Great video and you are very well spoken.

Great, great video!!! So happy vidoes like yours is on here!!!

have same job to do monday.....excellent video brother....first time i doing one

Would JB weld do better than RTV silicone to patch up that crack at the back to prevent oil leaks?

Thanks ur video help me alot im start today will see what happen

Thanks for your videos! Always saves my butt... my truck thanks you too!

Great lesson and perfect camara shots! Thanx

I like just putting the oil drain back into the cover to keep the dirt out, works great

My truck starts to lose power once it goes under a load such as going up a few different hills for pulling a loaded trailer. It starts to lose power then if I keep pushing it, it will eventually completely stall out then I have to wait a few minutes and it will start back up like normal. It'll then drive normal for just a little bit and then the same problem will occur again. Any clue as to what this could be? About every sensor on it has been changed. Has a new fuel pump, a new gasket kit was placed on the fuel pump housing, has new fuel filters, has a brand new turbo on it, it has been studded and deleted, it also has a fresh oil change. Just can't get to the bottom of the issue I have no idea what it is. With my ScanGauge I checked the oil pressure while it's running which gives me a live read out and it's in the correct parameters. After the turbo was changed at idle the oil pressure gauge is at zero and I get a check Gage light on. The second I push on the gas pedal it goes back up like it should but the read out on my scan gauge is showing its in normal range. I checked the ficm voltage as well when it's running and it's within normal range the lowest it's ever gotten is 13.5 v. Both voltages are right in line with each other. Also after the turbo was changed it now has a long start.

Also when it comes to people private OV. It’s all different now they can see what goes into their repairs . Their POV is everything a lot of time too

Question my friend. Have an 07 in here, did the oil branch tube with updated part, had to replace and injector due it getting smashed on the plug connector, pump seemed ok, now we still have a "no start" condition, also kinda sounds like it has a dead cylinder, as in turning it over it sounds like a dead cylinder. Before, it sounded normal when turning it over. ICP is not even hitting 15 psi, desired is over 1100, is it possible we did something wrong? Trying to hear air leaking not working out too well. The branch tube looked original, and it is able to swivel and move, and i dont see the white clip as per your video......great video, and thanks for your help. -Matt-

Thanks for all your help

Is there a video for the early model 6.0 hpop with the STC fitting that requires a tool?

quick question, I just did a hpop upgrade and after everything was put together I can't get it to start and it sounds like it's hydrolocked, any tips what to look for? thanks for videos and keep up the good work!

The bomb 6.0 ---7.3 IDI best diesel ever made.

Great video and great quality, thank you so much bro!

@FordTechMakuloco

10 жыл бұрын

No problem hope it helps.

We left the specialized socket for the IPR valve on it. The wire was on the back side holding socket on. Plus it will make it easier to get the IPR out next time and be a better heat shield than the cheap foil wrap with button.🤭

thank you so much for your help

@matrex2697

5 жыл бұрын

Wael Ahmed اخ وائل انا مشكلتي في نفس المحرك عندما يكون بارد يعمل لمده نصف ساعه وبعدها يتوقف انتضر لمده ساعتين حتى يعمل مره اخراى

Thanks for this video! You're a good teacher!

@FordTechMakuloco

8 жыл бұрын

Thanks!

@bettyabercrombie1933

7 жыл бұрын

FordTechMakuloco a

So when on bench and you turn pump both ways and you hear it pumping and there are no rough spots, the pump is good? Is there another way you can double check it.. Our fitting is definitely loose/worn so most likely that but all that work is lot if the pump is weak?

I have a 03 6.0 it run for about ten minutes then shuts off and won't start back up

I had the HPOP replaced on my 2004 6.0 .. it seems to misfire when I hit 55 to 75 mph. Is that common? If so how long does it take for the air to bleed out?

Can you still pressurize the oil system through the HPOP before you take off the stc fitting at this point?

thanks for this video. much helpful

Hi! Thanks a lot for your great vídeos, God bless You! Have a wonderful life and business...

Thanks for the videos. I picked up a cheap, early '04 F-450 recently and it's my first 6.0. It's been doing great, but the other day the oil pressure gauge went to zero sitting at a stop light. I double checked my ICP right quick, and it showed around 620 or so. I pulled over and checked the oil level and all was well. I changed the oil and made sure the plunger at the bottom of the filter housing was free. I used the stock cap and a motorcraft filter. I did notice a small piece of metal on the drain plug magnet, and there was what looked like a small piece of yellow plastic in the filter housing at the time of the oil change. When the engine is cold it runs normal with maybe a hint of a long crank. Once it warms up I'm getting zero oil pressure at idle again. I'm afraid it may be the beginning of the end of the HPOP, but is there any chance it's a problem with the sending unit for the gauge? I'm certain it's time for both coolers as well, but I have to tackle the biggest problem at the moment and let the others ride for a bit until the truck makes me some money.

@brandonsilvay4822

2 жыл бұрын

Check your low pressure sensor for your oil pressure cuz what that is that gauge doesn't show you on the dash your IPC your high pressure it only shows you your low pressure so you should have regular low pressure for everything else your h pop your high pressure is only for your fuel injectors that is the main thing that pressurizes the fuel injectors in order for the plunger to put more fuel pressure to atomize the fuel because your fuel pressure is actually low pressure like a carbureted gas engine it's low pressure through the engine until it hits the injectors the injectors raise the pressure they use electricity to release the magnetic plunger and oil pressure is what drives that plunger down to atomize the fuel and spray it into the high compression cylinder

@davidleeluderswhyibelievei9575

2 жыл бұрын

This is the exact problem I am having with my F350 super duty. My Machanic has has my truck for over o month and seems as if he has stalled out on working on it. He has told me now at this point that the lower pump is working but the top pump is not. He thinks it needs to be replaced. With this problem listed above do you think that he is correct. After watching your video here I think I will go get the truck and do the repair myself. If I do is it just a “high pump rebuild kit” I need? “

Honestly, I would rather be Cummin than Stroking. But my job has a Ford, and your video may be a great help, after we try the ETC replacement.

Loved this one keep up the good work

Hello I was hoping you can help me out. I accidentally dropped a bolt down blow the gears. I've used a scope to try and locate the bolt but I havent been able to now for a day and a half. Is there anyway it might of went into the oil pan?

Good job

My standpipes blew off the pump and cracked my housing any thoughts

I have a 2007 6.0 I'm going to do an EGR delete and a oil cooler I heard they upgraded the stc fitting on the 2007's is that true, should I do that as long as I have it apart, is there anything else I should while I have it taken apart?

How much does a job like this cost?

muy buen trabajo you are the best

Is it common for the pumps them selfs to go out. My 2005 f35 6.0 just started having this issue. Cold start no problem. Drive it around and nothing, Let it sit for a little for the oil to thinkin up and it starts up no problem. I have noticed oil leaking from the back side of the engine.

Great vid. It helped alot! Ty

Thanks a lot 👍for your video

How would you know if tne pump could be bad can i put air in the pump once it’s out of engine

What happens when the branch tube comes loose would that make it loose oil pressure to

Will three glow plugs not working cause a no start or the engine to idle for 10-30 seconds and shut off?

I like that flexible magnet who makes it?

⭐A Ford F 250 6.0 liter Powerstroke I have been helping work on and working onisn't running but it threw codes for three glow plugs and the EGR it starts sometimes and runs for 10-30 seconds and shut itself down, is this due to the bad glow plugs and the GPCM telling the engine to shut off????⭐

What scanner do you recomend

I have a 06 f250 6.0 it has a rough idle and it has a oil leak in the back im guessing its coming from the oil pump it cut off and wouldn't crank back the pressure gauge stop working but it did crank back after a few trys the pressure gauge went up but it dropped again could it be a oil ring leak on the oil pump or is the pump itself bad

Great video, thanks.

did your desiel not start hot or cold. mine does not start hot. dealer is srewed me on costs already charge me 2,000 and didnt even fix the problem. still wont start sometimes when hot. and ford are supposed to be experts

Nice video, I have a 2007 f250 that just died rolling on to the interstate. I have a crank no start no code issue but im dead in the water until I can get a scanner hooked up. What is the most common crank no start on the 07's? I'm praying its not the HPOP, I don't want to have to take all that shit off to get to it.

@wicodiesel9239

8 жыл бұрын

Being 05+... Either the STC fitting. Which is shown in this video, or something went through the IPR screen and is holding the valve open. Dummy plugs will USALLY be a crank no start while hot. Not a shut down.

@OfficialProducers

8 жыл бұрын

+Wico Diesel yep this was a while back but I ended up pulling the IPR valve and the screen was blown out. Replaced it with a new one and she cranked right up. Thanks!

i have a 2003 Ford Excursion 6.0 ... the truck has hardly runs , it starts but takes a while , but has no power . I was getting an icp high voltage code and repaired the harness ( all 3 wires were touching in the loom ) . I drove it with this code for a while, so my guess the wires were shorting each other for quite some time . I was told even if the icp fails the pcm has a default mode to still run ? I pin tested the icp circuit to the pcm plug , all is good no more shorted wires . Icp 29 Vref 36 and signal return 29 . ( all good to Pcm ) I have no power though it barely starts when it does have no throttle response ( 0 any in drive ) in nuetral hardly any very slow to rev ( no drive power of engine ) i bought a new hfcm and billet seconday fuel filter cap with the fuel tap fitting to test fuel pressure , I am 55lbs on the top cap. I put a blue spring kit a year ago , should I test fuel pressure at factory port ? I am at a loss , no more codes , besides Icp intermitten but now is gone and wont come back . Thinking my hpop failed , this is a 6.0 production date of 05/2003 so icp is next to Ipr . My ficm is in sync , voltage on ficm is above 48 ( i bought a new higher voltage one 2 years back whdn mine failed ) . whats next hpop air test for leaks ? Could my pcm become corrupted from icp wires touching ? All my values , voltages on Icp, Irp% , foot pedal voltage are in line .... I can tell u when i do a test with scanner engine ( when it runs) the scanner bumps the idle up , so that makes me believe that my hpop system is still tight . Any thoughts would be appreciated . Thanks Dave

On a no start, is their a chance it could just be the ipr and not the hpop? Or just replace them both because your there already there?!?

have you ever seen one that would max out at @2000psi ? I have done an air leak test from ICP and IPR ports and can find no leaks. I have not popped the cap off the HPOP because it's running and HOT starting but the ICP will not go over 2000PSI with a new ICP.

what test did lead you to the fitting

Also be aware of two 10mm bolts securing tins between up pipes and bolt to HP oil pump cover and WILL break cover if left in place

@strange_panda03

Жыл бұрын

Totally just found out about that 😂 the bolt on the bottom beside the two up top is extremely hard to get to if you don't have skinny arms

thanks for the video what kind of sealant do you use on the hpop cover when reistalling

Branch tube adapter will it work for 03

will this fix the oil leak the fitting was causing?

Do you have to take the alternator off

any time you see 0 ipr? just out of the blu stalled and no start from then

I have a 2006 F250 with a 6.0 diesel turbo charged I put a new high pressure oil pump in started up right away but for some reason it seems like it is sucking air I checked all the fittings it seems to be fine when you accelerate it that's when you hear like air being sucked it also has a smell of fuel does anyone know what this could be

Does anyone know if this is an expensive fix? Took my 6.0 into the shop for this exact issue

will it work for a 03

Hi, I installed a new fitting on my 06 350 and ran air to my icp port and I can hear air from right behind the hpop gear. Is that normal?

@mahdey

4 жыл бұрын

Yes

Good job tech

Thanks for your information 👀❗️🇺🇸👍😊

Old video but i have a question so I’m having crank no start replaced Ipr valve still no start I don’t have any way of knowing the Icp pressure. In the video you didn’t replace the hpop so it was just a seal issue?

my E450 6.0 leaks oil from the muffler outlet tube it could be the pump and it shuts off

How many hours does the book say to replace HPOP and how many does it take?!?

Hi I have a 06 ford f250 diesel and no start but when the towing truck inclined the truck to put the truck down I tried to start and it start right away and the guy put it down with the truck on and it keep working fine then I turn it off and tried to turn it on and it won't start can you help me please

I have a cold And a Hot no start. It will start with starting fluid. A y suggestions would Greatly be appreciated. Also I e doe a have replaced the dummy a stand pipes on both sides and right side nipple cups. I found a bad cup o-ring and did an ICP air test. And replaced the inj orings. It ran great till a out a year ago and. Haven’t worked on it since(I fell off a roof and broke quite a injurious) But now I Need my truck badly! I also noticed that their is exhaut coming from under my water pump? I have alot of $$$ into this but haven’t been able to physically work on it. Feeling better to be able to be able to work on it as much as possible. I live in N.H., so the weather has been pretty bad lately. ANY help or suggestions would be extremely appreciated!

What sice of soquet you need tobtake oyt the IPR???

great work

Truck died while driving.... then would crank and start then immediately die... added oil and the icp pressure went to the 400 range and wouldn’t even fire. Any thoughts? Always had long cranks to start.

That's awesome what you have it mounted to?

@FordTechMakuloco

10 жыл бұрын

just propping it up for now on engine and I am using the high lift trans jack as a camera mount for the 3rd person view it is a great idea I can raise, tilt and angle all I want like a real camera support used in movies the guys make fun of me. I want to find this claw device that had a weighted bag on the bottom of it.

Ran into one of these a week ago customer took it to 3 other techs, replaced HP oil pump 360psi was all icp tested good on modus ultra (snap on) replaced icp cranked and at 400 psi poof started and ran. Just because a sensor tests good doesnt mean its working. Ps Mac tools sells this socket pictured and can be removed w turbo in place.

We have a 6.0 that's been sitting with only 16k miles on it. I was told the HPOP needs to changed because the "seals" are dried out...wdyt??

I'm an automotive trainer....first off nice job.....very well done. I gotta pick on you for the Mopar RTV Mr. Ford guy.....lol

@FordTechMakuloco

9 жыл бұрын

evracer It is what we carry since we are dual dealer and the stuff works great. We do use the motorcraft stuff when general engine sealant wont do such as the 7.3l diesel and the front covers on the 3.5l engines then we use the exact special sealant from Ford.

@evracer

9 жыл бұрын

It is good stuff I agree...I have the cab off my own 6.0 right now doing head gaskets. Checking this while I'm in there.

@FordTechMakuloco

9 жыл бұрын

Good thinking!

How long Long would it take to crank before it fires up? I just did this and replacing my ipr and hope to have everything back together tomorrow

@acemavrick3

4 жыл бұрын

2 minutes

Den brukar silen fastna igen med metallparticklar å ventilen fastnar å kärvar! Men varför vart kommer metallparticklarna ifrån?

How did you diagnose that it was the STC fitting and not a faulty IPR valve?

@FordTechMakuloco

10 жыл бұрын

by leak testing as shown here- No Start: 6.0L Powerstroke ICP Leak Testing

I have a Ford 2007 when running for a limited period and when the engine turns off, it will not work again. What is the solution? Can I send you through your personal page?

@antoniosanchez3170

6 жыл бұрын

عراق الخير mi too my truck