What is the socket size used for opening oil filter?

@sanumotorswithcharlie

Ай бұрын

For the Nissan Qashqai (2014 - 2020), changing the engine oil and filter yourself is a straightforward process if you have the right tools. The socket size needed to open the oil filter housing is typically 27mm. Here are the basic steps for changing the engine oil and filter: ### Tools and Materials Needed: - 27mm socket (for the oil filter housing) - Oil filter wrench or strap (if needed for additional grip) - Drain pan - Ratchet wrench - New oil filter - New engine oil (check your owner's manual for the correct type and quantity) - Funnel - Gloves - Rags or paper towels ### Steps: 1. **Prepare the Vehicle**: Park your car on a level surface and allow the engine to cool down. 2. **Lift the Vehicle**: Use a jack and jack stands to lift the front of the vehicle, if necessary, to access the oil drain plug and filter. 3. **Drain the Oil**: Place the drain pan under the oil drain plug, remove the plug using the appropriate socket (usually 14mm or 15mm), and let the oil drain completely. 4. **Remove the Oil Filter**: Use the 27mm socket to remove the oil filter housing cap. If the filter is stuck, you might need an oil filter wrench or strap for additional grip. 5. **Replace the Oil Filter**: Remove the old oil filter and replace it with a new one. Ensure that the new filter is properly seated and that the O-ring is lubricated and in place. 6. **Replace the Drain Plug**: Once the oil has fully drained, replace the oil drain plug and tighten it securely. 7. **Add New Oil**: Use a funnel to add the new engine oil. Refer to your owner's manual for the correct type and amount of oil. 8. **Check for Leaks**: Start the engine and let it run for a few minutes, then check for any leaks around the oil filter and drain plug. 9. **Dispose of Old Oil**: Properly dispose of the old oil and filter according to local regulations. ### Tips: - Always double-check the size of the socket and tools before starting the job. - It's a good idea to replace the oil drain plug gasket if it looks worn out. For detailed and vehicle-specific instructions, always refer to your Nissan Qashqai's owner's manual or a professional repair guide.

Thanks Charlie. This is a great help.

@sanumotorswithcharlie

2 ай бұрын

Thank you very much 👍

What engine is this as my oil filter isn’t there 🤷‍♂️

Thanks for the vid. Can you add mode details about the square head you used for the seal nut? Thanks

@sanumotorswithcharlie

4 ай бұрын

The square-headed seal nut used for the sump of a Nissan Qashqai is typically designed to provide a secure seal for the oil pan or sump. This type of nut is commonly used in automotive applications to ensure a tight fit and prevent oil leaks. The square head design allows for easy installation and removal using a compatible tool such as a square socket wrench or a spanner specifically designed for square nuts. It's essential to use the correct size and type of tool to avoid damaging the nut during maintenance procedures. When replacing the sump nut on a Nissan Qashqai or any other vehicle, it's important to ensure that the new nut is of the correct size and specification to maintain the integrity of the oil pan seal and prevent leaks. Additionally, proper torque specifications should be followed to avoid over-tightening or under-tightening the nut, which could lead to further complications. If you're performing maintenance on your Nissan Qashqai's sump nut, it's recommended to consult the vehicle's manual or seek guidance from a qualified mechanic to ensure proper installation and prevent any potential issues. link for tool Universal Sump Plug Key Set 20pc Hex Square 3/8" Drive Oil Drain Tool W/ Gloves ebay.us/2hYi2B

Charlie, is that a 3-Tonne jack? I have a 2-Tonne jack, and it couldn’t even get the wheels of a 2010 Nissan Qashqai off the ground.

@sanumotorswithcharlie

Ай бұрын

It's possible that the 2-tonne jack you have might not be sufficient for lifting the Nissan Qashqai, depending on how you are using it and where you are placing it under the vehicle. Here are a few points to consider: ### Lifting Capacity - **2-Tonne Jack**: This jack can lift up to 2000 kg. While this should theoretically be enough for a Nissan Qashqai, the effectiveness also depends on the distribution of weight and how the jack is used. - **3-Tonne Jack**: This jack has a lifting capacity of 3000 kg, providing a higher margin of safety and might be more suitable for larger vehicles like SUVs. ### Vehicle Weight - **Nissan Qashqai**: The 2010 model has a curb weight ranging from approximately 1300 to 1600 kg depending on the specific model and trim. ### Tips for Effective Jacking 1. **Proper Placement**: Ensure that the jack is placed at the recommended jacking points on the vehicle. These are usually reinforced areas designed to handle the weight. 2. **Surface**: Use the jack on a solid, level surface to ensure stability and prevent sinking or slipping. 3. **Inspect the Jack**: Make sure the jack is in good working condition. A malfunctioning jack might not lift as expected. ### Upgrading to a 3-Tonne Jack If your 2-tonne jack is struggling or if you feel safer with a higher capacity, upgrading to a 3-tonne jack could be a good idea. It will provide more stability and ease when lifting heavier vehicles. If you are uncertain about the jacking process or the equipment, consider consulting the vehicle's manual or seeking assistance from a professional.