Very good, clear view of micro soldering. Thank you.

@GoCellPhoneRepair

2 жыл бұрын

Thanks for watching!

Great video. Thanks for this! Great soldering skills too!

@GoCellPhoneRepair

2 жыл бұрын

Glad it was helpful!

10:54 doesn't have to be flat....in fact it's gonna sit off kilter like that with the screw in It just needs to be on and connect I've been lucky enough and only my read has failed a few times- as long as all the pins are in the connector WILL work

Tolle Anleitung. 👍🏼

Where did you get the connector? I mean where can I buy it and what’s the name of it? Great video!

I kinda destroyed that part and looking to fix it. Just a little nervous about doing this though. I think the easy part is taking it off but my luck hasn’t been good lately

Can i replace a pin without solder?

What temperatures should I consider using? Thank you

What type of tape is that? I can't find any good tapes for soldering. that stick well, but that tape looks really good I would like to get some for my own work.

@PremiereHell

Жыл бұрын

Its heat resistant tape with no residue

Is there a digi-key/mouser link for this part?

Im considering fixing this. How much would it cost to replace this piece?

What's your price on a repair like this

What temp is your iron at?

Thanks a lot

@GoCellPhoneRepair

2 жыл бұрын

Happy to help

Hi there, I got the "1bit" problem and I switch the SDreader part with another one in a Switch who's working well, but the good SD part still does the "1bit" in the bad Switch and the first "supposed" bad reader does the "1bit" too in the good Switch.... So what must I do? changing the reader AND the connector on the first one? Cause when i put back the good SD (who's dont work on the first Switch) on the good Switch it works again without the 1bit thing...

@ToxicMothBoi

Жыл бұрын

Then you need exactly what he is replacing in the video. Ordered the part a couple days ago and fixing myself soon. Should be possible given the right tools

I just got all the stuff required to do this on Amazon, for less than 200, even a microscope camera, the same pins were missing from the board, they were still attached to the reader boards connector. They cost 9$ for 2 and the reader cost 9$. Microscope camera 250x zoom 39$, heat resistant tape with no residue 8.99$, 10 feet of copper sodder wick 8$,.a duel soldering iron and hot air station 80$ several tips and accessories, the heat gun all in one. flux 6.99$, also a new volt, ohms, amp meter. 10$ , 🤞hope it all works

@zskywarp

10 ай бұрын

So did it work?

Your material?

I repared it like 3 times and in a week it breaks again

@ioloiiuo

5 ай бұрын

Can i damage something by changing this pins

What type of lead and flux did you use

@GoCellPhoneRepair

3 жыл бұрын

Kester 63/37 and Kingbo RMA-218.

Why couldn't you just heat from under the board? Wouldn't that have helped your struggle @ 6:50 ?

@GoCellPhoneRepair

Жыл бұрын

There are components on the other side of the board.

@gageiannitelli6994

5 ай бұрын

@@GoCellPhoneRepair could you use thermal tape to protect that?

Happy New Year 2021 ;)

@GoCellPhoneRepair

3 жыл бұрын

Happy New Year Johnny!

Very nice job. last year i attempted this & my heat gun hand drifted hit my shield and went everywhere bar the connector lol, melted the plastic joycon connectors & flowed the nand :| i was waay too focused on alignment & took too long dicking about( also im a lazy soab & should have taken the nand off ) :( . best bit is, i could have just ordered the connector, pull 2 pins out , popped them in & touched them up. That was last year , too disgusted with myself to touch it so its in the back of my router cupboard , a sombering reminder of what i really am

@GoCellPhoneRepair

3 жыл бұрын

Thank you.

what's the thermal-insulating tape you use?

@GoCellPhoneRepair

2 жыл бұрын

Single Side Conductive Copper Foil Tape Strip.

Where can I send my switch for repair as I have the same issue

@GoCellPhoneRepair

6 ай бұрын

Please use the contact form here: gocellphonerepair.com/services/

Quick question, how old do I have to be to get a job in this industry?

@GoCellPhoneRepair

3 жыл бұрын

I would assume whatever the employment age requirement is in your area. If you are young then you might need to look into a work permit of some sort. Labor laws vary by state.

If I change the fpc connector, can I still mod my switch?

@TheMushMe

Жыл бұрын

This is just the sdcard reader connection, it doesnt affect the modability of your Switch

do you have a mail in service?

@GoCellPhoneRepair

2 жыл бұрын

I do. You can find details here: gocellphonerepair.com/get-a-quote/

i hate this sd card reader!!!!!!!!!!!!! its driving me nuts!!!!!!!!!! i ve been switchless for 1 year now.... I finally got my second replacement... did it myself with utmost care... but now it just decides to not connect properly! like i was installing cfw just fine then all of a sudden it stoped recognizing it! then i put it back, all was fine, and then it worked enough to boot into cfw, but couldnt install games and had low speeds!!! maddening