Fabulous! My basket on my 256 Rolabar stopped turning out in the field last year, probably going to have to do this rebuild, and I know I’ll be referring to your video big time when I do this, really appreciate this!

@CanadianRedneck15

7 ай бұрын

I am glad you found the video useful, thanks for watching!

Great old school tips I had a disc mower with a bad seal an put the grease to it just to get by the season worked fine my granddad told me this back in the day with final drives on old dozers good to see yea on KZread again watching yea from West Virginia take care

@CanadianRedneck15

3 жыл бұрын

I am glad to be back making videos too, thanks for watching!

Good to see your still at it

@CanadianRedneck15

2 жыл бұрын

I'm glad to still be here, thanks for watching!

Thanks for the tips, old school is the best school.

@CanadianRedneck15

8 ай бұрын

I am glad you enjoyed the video, thanks for watching!

Another fantastic video

@CanadianRedneck15

3 жыл бұрын

I am glad you enjoyed the video, thanks for watching!

Excellent vid man

@CanadianRedneck15

2 жыл бұрын

I am glad you enjoyed it, thanks for watching!

Like your films best When you describe tings, how IT shuld work and so on👍

@CanadianRedneck15

3 жыл бұрын

I am glad you enjoyed the video, thanks for watching!

Great video there Dave

@CanadianRedneck15

2 жыл бұрын

Glad you enjoyed it, thanks for watching!

Great video

@CanadianRedneck15

Жыл бұрын

I am glad you enjoyed it, thanks for watching!

Great vid Dave, its good NH still has parts available for their equipment though some parts are kind of expensive. Im currently rebuilding a NH 450 sickle mower top to bottom.

@CanadianRedneck15

3 жыл бұрын

Absolutely, doesn't matter how good a machine is if you can't get parts when it breaks! Thanks for watching!

@bobstowe6749

2 жыл бұрын

Joe's Machine shop in PA.

Jak zawsze bardzo ciekawy film👍

@CanadianRedneck15

3 жыл бұрын

I am glad you enjoyed the video, thanks for watching!

Thanks for sharing 👍

@CanadianRedneck15

3 жыл бұрын

Thanks for watching!

Thumbs up Dave.

@CanadianRedneck15

3 жыл бұрын

Thanks MB.

Very informative video! Approximately how many dollars (Canadian or US) did you spend rebuilding the gearbox?

00 grease probably would work pretty good in there also, but seems a little harder to find around here, at least for me, and about $20 a bottle where I get it.

@CanadianRedneck15

3 жыл бұрын

Thanks for the information and thanks for watching!

Seems there would be a inch-pound torque spec for those bearing preloads. The same way you do when building a differential and setting preload on the pinion nut. Its not hard to measure.

@CanadianRedneck15

Жыл бұрын

It's possible, I don't have a manual for the rake. Thanks for watching!

Your videos helped me out a lot on my IH 444 question thinking quick change from bucket to forks,, the pressure does not hold allied 350 forks any suggestion? no leaks

@CanadianRedneck15

3 жыл бұрын

You have oil leaking by, either the valve or the lift cylinders will need rebuilt. Thanks for watching!

@BillyBob-fd5ht

3 жыл бұрын

@@CanadianRedneck15 valve would be it, just replaced one cyl,

Thanks for the Video. Very well explained. I have to do the same with my 56. Cant find new gears. All I can locate is used ones. Do you have a website for the parts. Thanks

@CanadianRedneck15

Жыл бұрын

I ordered them from a New Holland dealer. Thanks for watching!

@joshuaburkey5841

Жыл бұрын

Joes machinery in pa 100% reccomend they manufacture aftermarket nh parts 717.464.1043 is th ph. #

@CanadianRedneck15

Жыл бұрын

@@joshuaburkey5841 Thank you, always good to have this kind of information! Thanks for watching!

The wind blowing into the mike is hard on the ears. 😏

@CanadianRedneck15

3 жыл бұрын

Yeah, wind sucks.

@donfenton9082

2 жыл бұрын

What wind?

Good day from Ont. Boy interesting video. Yea my dad always oil is cheap, compared to new parts. What did everything cost ? Thanks

@CanadianRedneck15

3 жыл бұрын

The gears were the expensive part but parts total came in around $700-800. Thanks for watching!

Goldddddd

@CanadianRedneck15

3 жыл бұрын

I am glad you enjoyed the video, thanks for watching!

Dave. Wondering why you didn’t load each barring with grease like a wheel barring ????

@CanadianRedneck15

Жыл бұрын

Hi Mark, these bearings run in gear oil so no need to pack them. Thanks for watching!

I’ve seen your other vids about IH 444 and the other models and they’ve helped me out alot. Im gonna change hydraulic pump in my ih 444, and the instructions say that I need to open the ”over pressure valve”, dont know what it is called in english.. And then run the engine for 30 minutes. Then adjust it so I get the right pressure. I cant find where I can adjust this.. Hope you know what I mean..

@CanadianRedneck15

3 жыл бұрын

Is that in a manual for a 444 or just generic instructions? As far as I know you just change the pump and make sure it has oil.

@MeKaLMeKaL

3 жыл бұрын

@@CanadianRedneck15 That had not even crossed my mind. The instructions is in a note that i got with the pump when I ordered it. It may be generic instructions? Do you think I just can change the pump and then run the tractor as normal?

@CanadianRedneck15

3 жыл бұрын

@@MeKaLMeKaL I would say that yes those are just generic instructions. Change your pump, top up the hydraulic reservoir and let the tractor idle for 5-10 minutes, check your levers for function and if everything seems fine you're good to go.

@MeKaLMeKaL

3 жыл бұрын

@@CanadianRedneck15 I changed the pump and it all worked out fine. Thank you for input, and continue the good work with the vids, they’re great. 👍

@CanadianRedneck15

3 жыл бұрын

@@MeKaLMeKaL That's great, I'm glad I could help!

Do you have a part number for the seals??? We have the same problem an have to replace berings an races an seals... we can not find the seals.. any info would be appreciated...thanks in advance...

@CanadianRedneck15

2 жыл бұрын

You can find the numbers on the Ford/NewHolland website parts lookup. Thanks fro watching!

I took the four bolts holding the gearbox on the rake and I can not get it to slide off the rake

@CanadianRedneck15

2 жыл бұрын

Did you also remove the reel from the hub? If all else fails use a bigger hammer. Thanks for watching!

Where did you order your parts from? Thank You

@CanadianRedneck15

2 жыл бұрын

I got them from a New Holland dealer for this rake, most stuff I get through myself, I'm a parts dealer. Thanks for watching!

Why not grease the bearings when they were installed

@CanadianRedneck15

4 күн бұрын

Because they are meant to run in gear oil. Thanks for watching!

How do you plan to put on rake 😂😂

@CanadianRedneck15

8 ай бұрын

I don't, the customer just brought the gear box. Thanks for watching!