I just got mine 2 days ago. Found your video and I'm so glad I did. I'm always intimidated by tools that need to be carefully and have in depth assembly. I'm always afraid I'll get something wrong. Your video has eased my tension on getting this right! Loved it and Thank You!!!

@NorthwestCraftsman

3 жыл бұрын

I’m so glad you appreciated it! Hope yours serves you as well as mine has me!

@Benmeglei1

11 ай бұрын

Hey, it’s been 2 years since you got it. How do you like it?

Very precise instruction. No rambling nonsense. Great job! Subscribed.

I admire your delivery, your short concise voice over is very easy to follow. You are an good teacher. You held my interest even though I knew what subject matter was up next. Thanks for your evaluation!

@NorthwestCraftsman

Жыл бұрын

Thanks Leroy! I appreciate your kind words!

Fantastic video. You've sold me on this unit and I will be reverting back to this video to make sure I'm setting it up properly along with the manual.

@NorthwestCraftsman

3 жыл бұрын

Thanks Frank! I appreciate the kind words and am glad this video was helpful for you! If you come across anything during setup hay wasn’t answered, feel free to drop it here!

I appreciated your video, but I appreciated all of the respectful replies you've made to others in the comment section even more. Thanks for being a decent human being. Subscribed.

@NorthwestCraftsman

2 жыл бұрын

Thank you! I really appreciate your compliment. Glad to have you as a part of the community! Josh Northwest Craftsman

I have one of these tables and my top was warped, as someone else has mentioned in the comments. I contacted Bosch and they sent out a new top, so kudos to them for the customer service. Unfortunately, it was also warped. I took a couple hours and was able to flatten it a bit by knocking down the high spots (with elbow grease and some sand paper on a slab of flat granite). It helped a considerably, but there are still low points and the top still isn't flat enough to support workpieces for something like nicely fitting rails and stiles. I've continued to use it for less precise work, but plan on getting a new table top, plate and fence when I finally tackle the upcoming kitchen project.

@NorthwestCraftsman

3 жыл бұрын

Interesting! I’m sorry to hear about your experience with the table tops. It’s possible I’m just not nearly as attuned to minor differences that some of the users (yourself included) are seeing. Glad Bosch at least tried to remedy the situation. Thanks for the comment!

Great video. I just bought the same table and router from a fellow woodworker for $225. They were brand new in the box. The table top will fit perfectly in my Ridgid table saw extension. I am happy to hear that you said it comes with shims to joint. Hopefully I can get it set up tomorrow.

@NorthwestCraftsman

3 жыл бұрын

Awesome! That’s a steal of a deal! Happy building, I’ve loved having mine around.

@stevesiefken6432

2 жыл бұрын

I’m thinking of getting this router table and same router you have. You still like the router table? Is it level?

@rchavez5056

2 жыл бұрын

@@stevesiefken6432 I do like it. I have never had any issues with the table or router. 👍🏼

Just watched the video. Getting mine in the mail tomorrow! Appreciate the tips!

@NorthwestCraftsman

3 жыл бұрын

Glad you enjoyed it! And awesome!! I love mine and use it all the time.

I purchased the same table from Lowe's about 2 years (had to special order it) ago and it is still going strong (just used it today). Great video!

@NorthwestCraftsman

3 жыл бұрын

Sweet! Glad to hear it’s still going strong!

@johnyabut5887

3 жыл бұрын

@@NorthwestCraftsman how much this router ?

@NorthwestCraftsman

3 жыл бұрын

@@johnyabut5887 both the router and table can be found on Amazon at the following links 😊 prices will vary depending on when you check. Router Kit, Bosch 1617EVSPK: amzn.to/2HE72Kk Router Table, Bosch RA1181: amzn.to/37OY0W6

@smattt

8 ай бұрын

How easy is it to square the fence to the bit? I have an older Ryobi router table and it is a massive pain to properly align the fence.

@Haunter131313

7 ай бұрын

@@smatttpersonally I think any squaring is a pain in the rear but it’s less complicated than others. Just take your time and don’t get too frustrated. All-in-all not too bad.

Really helpful. I've read mixed reviews about this table, but this reassures me. I reside in S. Africa so I'll need to import it from the US or Europe. A big investment, so it needs to be good. Thanks for your time making this.

@NorthwestCraftsman

3 жыл бұрын

I’m glad you appreciated it! Happy woodworking!

Researching router tables, I came across this video. Glad I did. After looking at some of your other content, you have a new subscriber.

@NorthwestCraftsman

2 жыл бұрын

Thanks Wade! I'm glad you found it useful and glad to have your around! Josh Northwest Craftsman

Waiting for my table to come in a couple of days after finding out my Bosch does not fit my old table. Have to say that I enjoyed the video, clear, concise and easy to follow. Have bookmarked it for when the table comes in. Not only did you have great views as you assembled the table, but the speed you did it in along with your oral tutorial was smooth and easy to follow. Thank you sir, I will be checking out your other videos as well. Joey

@NorthwestCraftsman

5 ай бұрын

Thanks! I’m so glad you found it helpful! Good luck with your set up and enjoy your new table!

Very happy i watched this. Thanks!

@NorthwestCraftsman

3 ай бұрын

Glad you found it helpful!

Thanks for the detailed video it will help a lot of folks

@NorthwestCraftsman

10 ай бұрын

Glad you think so!

Great video man keep em coming. Maybe you could bring us along on some projects. Also thanks for posting the model numbers for the Bosch parts used. Going to pick up a combo myself.

@NorthwestCraftsman

3 жыл бұрын

Thanks for your kind words! And projects are on the way! Have you seen the bed frame video yet?

Bought this table immediately after the video from your link. Thank you for a great demo.

@NorthwestCraftsman

3 жыл бұрын

Thanks! I appreciate your support of the channel and hope you enjoy yours as much as I have mine!

@TheAyotteMan

2 жыл бұрын

@@NorthwestCraftsman Lowe’s and or Bosch needs to be sending you some goodies for making them some money!!

@NorthwestCraftsman

2 жыл бұрын

@@TheAyotteMan I do make a small affiliate percentage from Amazon purchases for anything linked through there but I would not argue with your proposal!

This is the second video of yours I’ve stumbled upon in my pursuit of picking up wood working as a hobby. I just picked this model up and researched it on KZread and your video helped a lot. Decided to subscribe as I like your format and approach and look forward to seeing your other videos.

@NorthwestCraftsman

3 жыл бұрын

Sean, thank you very much for your kind words! I’m glad you find the videos useful and am glad to have you as a part of the community! Look forward to seeing you around.

Excellent video. Very concise and easy to understand. I am in the process of deciding which router table to buy. Your video has not only convinced me to get this one, but has eased my fears about set up and leveling. Thank you for posting this. It was extremely helpful.

@NorthwestCraftsman

Ай бұрын

So glad you found it helpful! This router table has been great for me and is a perfect starter, especially if you don’t want to build one.

Thank you for this video. I am currently looking for a table on a budget this video has made up my mind

@NorthwestCraftsman

2 жыл бұрын

Glad you found it useful!

great video thanks for sharing, i bought one on marketplace that someone partially put together got frustrated and sold it for like 100 bucks he had the leveling screws attached to the plate, and a few other things were not correct, i just received the Bosch 1617 for Fathers Day , thanks for sharing

@NorthwestCraftsman

Жыл бұрын

Hey! Sorry for the late reply, glad you got it worked out! And yea, that’s no good when you used equipment like that.

Excellent video.

Thanks for the info. Nice video

Followed your Amazon link and purchased. Thank you so much for the video. subbed and liked

@NorthwestCraftsman

3 ай бұрын

Thank Frank! I appreciate your support and compliment!

Good clean video.

just what I was looking for....

Thank's from us lady's out there your video was very informative 👌

@NorthwestCraftsman

Жыл бұрын

Glad I could help! 😊 Happy Woodworking! Josh Northwest Craftsman

Great Video - Thanks!

@NorthwestCraftsman

7 ай бұрын

Glad you liked it!

Great video. Thanks.

@NorthwestCraftsman

Жыл бұрын

Of course! Glad you found it useful!

Good video. Was about to build a new table, but I think you changed my mind.

@NorthwestCraftsman

3 жыл бұрын

I’m glad you appreciated it! Here’s a quick link to the table and router if you need it. Router Kit, Bosch 1617EVSPK: amzn.to/2HE72Kk Router Table, Bosch RA1181: amzn.to/37OY0W6

@protakill

3 жыл бұрын

Me too. I think I'll just buy this router table. I'm new to woodworking and I think this will help a newbie hit the ground running a lot faster.

@stevedaniell7643

3 жыл бұрын

@@NorthwestCraftsman That’s one of my routers and my favorite by far. Have the fixed base in my old table and use the plunge base for everything else.

Great video; thank you!

@NorthwestCraftsman

2 жыл бұрын

So glad you enjoyed it!

Thanks and excellent.

Just got my 1181 from Amazon and assembled tonight, can’t wait to use it! I also ordered the dust collection adapter for the 1617 router that you demo’d from Etsy. That looks like it will prevent any dust from getting out, though I do think it will be a bit of a hassle to change bits. It would be worth it to keep the dust to a minimum.

@NorthwestCraftsman

2 жыл бұрын

Awesome! 😄 I’m excited for you to get to use it! I was thinking the same thing about the bits but another viewer commented about Bosch’s “Offset Wrenches” and sure enough, they have some. They allow you to change the bit from above the table much more easily. Here’s a link! I’ll probably be getting a pair myself. Offset Wrenches. amzn.to/34zl0Jm

@troy9485

2 жыл бұрын

@@NorthwestCraftsman sweet! Ordering them now! Thanks again

I need to get more of that on off action

My table is coming next Wednesday (12/13/23. Can't wait to use my new toy with my new router. Great video.

@NorthwestCraftsman

6 ай бұрын

Awesome! I’m excited for you to get to crack it open! I’ve loved mine.

I had the Craftsman version of both the table and router. The router I loved but the Craftsman version of the table fence wasn’t so good because I couldn’t align the fence at the opening and work pieces would hit the out feed fence and get caught. I purchased the Bosch router today and will be purchasing this table next!! Thanks for the review!!

@NorthwestCraftsman

Жыл бұрын

Oh man! That would be a huge pain! Glad you found the video helpful and hope you find the combo as useful as I have!

thank you, excellent tutorial.

@NorthwestCraftsman

3 жыл бұрын

Glad you liked it!

Bosch should be paying you as an instructor on how to use their tools. Great vid.

@NorthwestCraftsman

2 жыл бұрын

Haha, much appreciated! Glad you found it useful!

Wow I'm buying!!!

@NorthwestCraftsman

Жыл бұрын

Love mine! Hope you love yours too!

good explanation. Thanks for the hints. have now subscribed to your channel.

@NorthwestCraftsman

3 жыл бұрын

Thanks Stan! Glad to have you as a part of the community!

Thank you.

Great video

@NorthwestCraftsman

4 ай бұрын

Thanks! Glad you liked it!

Good video ! Just bought the table and hoping to buy the same router for the exact set up you have !

@NorthwestCraftsman

3 жыл бұрын

Anderson Jimmy exciting! 😄 I’m sure you’ll love them just like I do !

Thanks for sharing

Hey bro! Nice video!! I like it bro good job

@NorthwestCraftsman

Жыл бұрын

Thanks! I'm glad you appreciated it!

Your review sold me. I have the Bosch dual level miter saw so I expect this sort of complexity (that German engineering), but what surprised me is the dust collection (the dust collection on their miter saw is....cute lol)

@NorthwestCraftsman

8 ай бұрын

Bosch really nailed it with this one. I’m glad I’m not the only one that appreciates it. Have fun with it!

you did a good job.

@NorthwestCraftsman

3 жыл бұрын

Thanks Daniel!

Thank You.

Looks like this is the table I’m getting. Bought a Kreg thinking it’d be a little better, but I’m missing several fasteners. Should have just went with the Bosch to begin with.

@NorthwestCraftsman

2 жыл бұрын

Shoot! I’m sorry to hear that! Hopefully you’re able to get up and running quickly

Good for you for being able to slide the router in so easily. I CANNOT do it. Ended up buying a second router just so I wouldn't spend 30 minutes of my life trying to get the thing to slide into the housing.

@NorthwestCraftsman

3 жыл бұрын

Shoot! I’m sorry to hear that. At the risk of asking a really dumb question, are the arrows lined up when you’re trying to slide it in? It’s also possible yours has more interference which causes it to bind up.

@nickbailey202

3 жыл бұрын

@@NorthwestCraftsman I appreciate it. If you Google it, you'll see lots of people have the same issue. Something about the type of metal- sm ooth to slide into the housing, but it's it gouges easily and skews the geometry just enough

@NorthwestCraftsman

3 жыл бұрын

Interesting! That’s good to know. Seems like Bosch could put some polycarbonate glides in there to ease on the mental on metal interface. Glad you were able to find a solution, even though it was quite expensive.

Thank you for doing this video. I'm looking at getting a router table for building a computer desk and this video eased some of my concerns on putting it together and using it.

@NorthwestCraftsman

2 жыл бұрын

Glad to hear it! It’s a great table and it plus the router are a total work horse. Send some photos of your desk when it’s done!

High Five Thanks !!!

@NorthwestCraftsman

3 ай бұрын

🙋‍♂️💥 Glad you found it helpful!

Great video. I think this helped me decide on this table. Would love to see how you feel about it 2 years later?

@NorthwestCraftsman

9 ай бұрын

Glad to hear it! I still love it and use it often! Only complaint is I wish it was bigger but for a first table, it’s perfect 👍

I picked up the cabinet style one bosch has. I like it it's heavy. And worked out really good on my flip top table with my plainer. But the insert is so rough. But all in all. I'm happy with it it work and thanks what I wanted. Functional. 😁great video dude. Keep it up

@NorthwestCraftsman

3 жыл бұрын

Thanks Michael! I appreciate the positive feedback! Glad to hear you're enjoying your table as well! This one is an absolute work horse. Bosch has done a great job!

Hi! Thank you for sharing your video, it was very informative. I am considering making my own T&G flooring to cut cost. I am presently shopping around for the best option. I know it will be time consuming to make my floors but I don't mind that. What I want to know is , do you think this table and router can handle 2000 s.f. of flooring?

@NorthwestCraftsman

3 жыл бұрын

Thanks! I appreciate the compliment and am glad you found it useful. Sounds like a fun project! I think the table and router can definitely handle this. What I would be careful of is your speeds, feeds, and bit sharpness. Heat is your enemy and the faster and more aggressively you cut, the more your bit will dull which only makes it worse. I recommend you get a nice freud tongue and groove bit set and evaluate sharpening it throughout the project (usually have to send carbide out). Freud Tonge and Groove Set amzn.to/3oKDFqr

You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzread.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.

@NorthwestCraftsman

10 ай бұрын

Totally agree! Bosch did a really great job with this.

Nice set up, where did you get the router itself and what was the model number for the table and router ? thanks.

@NorthwestCraftsman

3 жыл бұрын

Thanks! I got both the table and router from Amazon. The links below have the model numbers and should get you there. Router Kit, Bosch 1617EVSPK: amzn.to/2HE72Kk Router Table, Bosch RA1181: amzn.to/37OY0W6

Thanks excellent video helped me decide to order one. It will be here this week. Don't think I could build one for much less than the selling price $199.00 shipped on Amazon

@NorthwestCraftsman

3 жыл бұрын

Congrats! Very exciting to have both of those on the way! I also couldn’t agree more about the price for a table. Given where I am in my woodworking career, I probably couldn’t make a table of this quality for that price.

@rcboals

3 жыл бұрын

Just put put.it together this morning. The instructions in the manual are very very good, just like you said. Your video really helped with cutting down the time it took to put it together took less than thirty minutes thanks to your video. I am now a subscriber to your channel.

@NorthwestCraftsman

3 жыл бұрын

@@rcboals welcome! We’re glad to have you as a part of the community! I’m also glad that this video helped you put your new table together. Hopefully you get a ton of good use out of it and can make some awesome projects!

@kurtn8057

3 жыл бұрын

Just got mine from amazon today. Great instructions...easy assembly!

@NorthwestCraftsman

3 жыл бұрын

@@kurtn8057 great!! Glad to hear it! Hope it serves you as well as mine has served me! 😄

Do they provide base-plate measurements? I have an older Makita 3612BR router that I'd like to put in one of these but it's not on their posted list of supported routers. The 3612BR appears to have 4 holes 85mm apart in a square pattern. Would there be room to drill (it's aluminum, correct?) additional holes in the base ?

@NorthwestCraftsman

3 жыл бұрын

They do! Below is a link to the PDF of the manual. Page 14-15 is what you’re looking for but it doesn’t look like your Makita model is included by default. And there should be room to drill if needed, yes, it’s aluminum 👍 Link to Manual pdf.lowes.com/operatingguides/000346353679_oper.pdf

Did Bosch quit putting the elevation adjustment on these? They used to come with an Allen wrench with a T handle to run the router up and down.

@NorthwestCraftsman

2 жыл бұрын

Nope! It’s still there. It comes with the wrench but you’ll still need a router mount that has the bottom side adjustment. The fixed base in the Bosch 1617 EVSPK kit has that.

Liked and subscribed.

@NorthwestCraftsman

2 жыл бұрын

Welcome and thank you! Glad to have you as a part of the community!

What’s the clearance below it . And can you use a larger router.. I.E porter cable 3.1/4 plunge and is the table set up for micro adjustment with a plunge . Thx any info will save me time much appreciated.

@NorthwestCraftsman

3 жыл бұрын

- Clearance is about 9” from bench top to the top of that window underneath. - Not sure about the size of router, really depends on how big it is. I would imagine if Bosch has the router plate pattern for your router, it’ll work. No guarantees though. - It is set up for micro adjustments from the table top and honestly that is one of my favorite features.

great vids. question... early in the vid. you stated ra1181 is and upgrade from the ra1171. do you know the difference? I seen online a package deal for the router and table. (1617evs and the ra1171) looking to pick it up but just wanted to see the difference in the table thx!

@NorthwestCraftsman

3 жыл бұрын

Hey Michael! Thanks for the question. Honestly there aren’t a ton of differences and I think a lot of it would come down to preference. I like the aluminum top for the 1181 and the more open design which allows for easier cleaning. That being said, I haven’t used the 1171 so I can’t speak from direct experience. Below is an article I found which goes through some of the differences, though, it is a little circuitous in its style. www.ronaldphillipsantiques.com/bosch-ra1171-vs-ra1181/

@michaelnunez5701

3 жыл бұрын

@@NorthwestCraftsman thx keep up the good work/videos!!

Now I want to unbox mine

@NorthwestCraftsman

3 жыл бұрын

Do it! 😄

I would ask what Northwest Craftsman thinks about the use of the Bosch Above-Table Hex Key RA1165 with this table? Is it helpful? Is it worth it to purchase with the table? I appreciate the great video. Thank you for the excellent assembly review!

@NorthwestCraftsman

Жыл бұрын

Glad you found it helpful Brian! I’m not sure of the product code you listed but the hex key that comes with this table, RA1181, is incredible. Easy to use and very precise. Just make sure to undo the friction lock on your spindle before adjusting.

Would love to get one but down under we use 240 volts and I can't see any that can run on that voltage. Strangely Bosch only seem to have made this for the USA market. Can't use a step down transformer either as the vac system and router are all 240 volts. Was the tabletop dead flat?

@NorthwestCraftsman

2 жыл бұрын

Shoot! I hadn’t even thought about that but think you’re right because most of Europe is at the same voltage as you. If you find a solution, comment back because I bet you’re not the only one. And dead flat is a little of a trick question. I believe I remember measuring it to within 1/64” or 1/128” of “flatness” by my 36” level and any gap present. But at that point I start to question my level as I haven’t had it checked or certified, just assumed. For me, there wasn’t any obvious twisting, bowing, or cupping of the table which is flat enough for my work. If you need a truly, sub thou flatness, I’d recommend making one with melamine or the like because you can get some wicked flat and slick surfaces that way.

Very nice video. One question I have is when you purchase this it does not come with a router, correct? Just the table is sold separately and you will need to buy the fixed router separately.

@NorthwestCraftsman

3 жыл бұрын

Thanks! You are correct! The table and the router are sold separately. You can find them linked below if you're interested. Router Kit, Bosch 1617EVSPK: amzn.to/2HE72Kk Router Table, Bosch RA1181: amzn.to/37OY0W6

how is this router table compared to a gts10xc with a dado stack? great video man!

@NorthwestCraftsman

Жыл бұрын

Great question and thanks! I don’t have that setup but if you’re only looking to cut dado’s a table saw is probably the way to go. This is more useful if you have other profiles you’d like to use like rounds, changers, etc.

Such an improvement on the 1171 I have

@NorthwestCraftsman

3 жыл бұрын

Awesome! For a user that hasn’t used the 1171, what are the biggest improvements?

Will the Bosch table accommodate a router lift from kreg or woodpecker

@NorthwestCraftsman

Жыл бұрын

Great question! I’m not sure. Here’s a link to the manual, page 15 has compatible routers with the base plate and I think it has dimensions as well. pdf.lowes.com/productdocuments/33317c1b-1aec-45b5-9eae-46caa8e591db/08063444.pdf

I've got the same one coming in this Monday 9 -28. I'm 2nd guessing with all the negative comments about bits getting stuck , unlevel surface etc. I've got the 2 1/2 hp Harbor Freight one. Its about a week old, still hasn't been used yet.. Nitpicking about which bits to buy. Looking at the 70 Bit Professional C3 Carbide Router Bit Set - 1/2" Shank - Yonico 17702..

@NorthwestCraftsman

3 жыл бұрын

ccdirectt vdllc I saw a bunch of the negative comments as well but haven’t had any issues with mine. Perhaps it’s a batch inconsistency issue? The bits honestly make a huge difference. I got a cheap set off amazon which gives me a variety and then a nice Freud bit (3/8” up spiral bit) and I love it.

Much better than your router review video

@NorthwestCraftsman

3 жыл бұрын

I can totally understand that. The router table was far more interactive to put together. As a followup on the router though, I have been very impressed by the combo. It’s held up to a lot of abuse and endless hours of work. Happy wood working!

Can you adjust the height of the bit from the top of the table?

@NorthwestCraftsman

2 жыл бұрын

Sure can! If you’re using the Bosch 1617 EVSPK fixed base, it’s in the front left.

I wonder if I’m older Dewalt DW610 will fit in this table

@NorthwestCraftsman

Жыл бұрын

Doesn’t look like the 610 is compatible but double check page 15 of the manual below. pdf.lowes.com/productdocuments/33317c1b-1aec-45b5-9eae-46caa8e591db/08063444.pdf

Do you know what the key holes are for in the miter slot in this table?

@NorthwestCraftsman

Жыл бұрын

Great question! I think they’re for the feather boards that come with the table. But, I can imagine other attachments being compatible as well.

Does this table come with above the table height adjustment?

@NorthwestCraftsman

3 жыл бұрын

It does! The table itself doesn’t have a lift but interfaces with the 1617 EVS router frame to access the micro adjust from the table top. Below is a link to the EVS Bosch 1617 EVS amzn.to/3rOIf82

Great👍

@NorthwestCraftsman

Жыл бұрын

Thanks! Glad you enjoyed it!

Is that a palm router that you installed, or a mid-size model? Will it even accommodate larger routers?

@NorthwestCraftsman

2 жыл бұрын

It’s a midsize model (2.25 horses) from this 1617EVSPK kit. amzn.to/34aPK2V

Can you make height adjustments?

@NorthwestCraftsman

2 жыл бұрын

By itself, no, but that the router plate has a hole that integrates with the 1617EVSPK base for table top access height adjustments 😊

Hi NWC! Thanks for the video. Very informative! Some questions regarding the height adjustment feature of the fixed base when mounted to the router table: 1- Is it a good replacement of a router lift? 2- Is it accurate? 3- Is it easy to use? Thanks for sharing. Saludos from Mexico City.

@NorthwestCraftsman

Жыл бұрын

¡Buenos dias mi amigo! Gracias por la pregunta. Excellent questions. I would say it’s a great replacement for a router lift, it’s extremely accurate (I can easily move it within a few thousandths of an inch), and it’s very easy to use. Just make sure to undo the friction lock on your base before adjusting. Tenga un buen dia! Josh Northwest Craftsman

@rafaelmijares9197

Жыл бұрын

@@NorthwestCraftsman muchas gracias por tu rápida respuesta Josh! Buen fin de semana!

Very nice. Thanks for help with assembly. The confusing part is all the screws. All these terms: truss head, pan head, #10 by xxx. Why didn't they just color code the 400 screws that are included? Then they would say, put the phillips head (ORANGE) screws (4) into points, etc. Part of your video that really helped was when putting on router plate (aluminum) at point 4:29. One doesn't actually put the 8 screws THROUGH the holes but only uses them for leveling. I know that was said in the instructions but because I didn't have 8 screws anymore (2 were put in wrong location on dust port) it was very confusing. Your video is very helpful, though so I took out the 2 from dust port and now had 8 for top plate. What about that round, clear plastic piece - is that supposed to attach to prevent chips from flying up? No mention in manual or in your video? It's about 3 inches in diameter and has a place for a screw at one end.

@NorthwestCraftsman

3 жыл бұрын

Thanks for the compliment! I agree color coding would be a good idea on their part. In the screw bag is a small post like screw with a flat head top. Put that inside the post of that clear piece and screw it into the router plate at about the 2o’clock position. It’s intended as a shield for routing without the fence.

@NorthwestCraftsman

3 жыл бұрын

On a side note, I see your user name, are you from Colorado?

I was looking for a table for my new Bosch GMF1600CE, and really liked it by your video, but wondering if I would be able to install my router on it, I can't find any information about if this table is compatible with my router. Does anyone have any idea about this?

@NorthwestCraftsman

2 жыл бұрын

Thanks! I’m glad you enjoyed it. Below is a link to the manual, page 15 has the list of compatible routers. I don’t see yours right off the top, but I may have been looking wrong. Bosch RA1181 Manual pdf.lowes.com/productdocuments/33317c1b-1aec-45b5-9eae-46caa8e591db/08063444.pdf

Awesome video. How can I remove a quarter on an inch wood out of a 5 by 3 inch piece of wood ? I appreciate your time. Thank you very much.

@NorthwestCraftsman

3 жыл бұрын

Thanks for the comment! Are you trying to remove it across the entire surface? Or just a specific area?

@TheJosa007

3 жыл бұрын

@@NorthwestCraftsman I like to remove it across the entire area in a commercial set up. Thank you for taking the time to respond

@NorthwestCraftsman

3 жыл бұрын

No problem! A planer is the tool I’d use but 3x5 is too short for most if not all planers which means you’ll either need to double sticky it down, or plane it before cutting them to 3x5 (this is the route I’d go).

Can you tell me if the router height is adjustable from the top with the supplied base/mounting plate? I have the same router ordered that you show.

@NorthwestCraftsman

3 жыл бұрын

It sure is! If you mount the fixed base of the EVSPK to the router plate, there is a hole that aligns with the fine adjustment knob and an included hex key to do the adjustment.

@donvines9101

3 жыл бұрын

@@NorthwestCraftsmanWow - Thanks so much for the quick response, and great video! :)

@NorthwestCraftsman

3 жыл бұрын

Thanks! Glad you enjoyed it and found it useful!

Do you feel the red insert ring is too thin and the final surface is not flush enough?

@NorthwestCraftsman

Жыл бұрын

I’ve gone back and forth. It’s certainly not flush but I don’t generally rely on it to datum my parts, just prevent them from falling in. Bosch certainly left room for improvement.

FYI. Bosch makes recessed wrenches! It made my life much easier!

@NorthwestCraftsman

3 жыл бұрын

Kiran Bhat Woodworking I didn’t know that! Thanks for sharing!

@KiranBhatWoodworking

3 жыл бұрын

@@NorthwestCraftsman Yes! RA1152 is the part number. Changing bits is much easier and with the top depth control, it removes the need to buy a router lift!

@fxp2741

3 жыл бұрын

I've got the Bosch portable router table, not nearly as solid as the aluminum top model. I picked up my recessed wrenches at Amazon because it is a hassle to change bits otherwise, a necessity.

How do you manage dust collection?

@NorthwestCraftsman

2 жыл бұрын

There’s a 2-1/4” port on the back of the fence which works pretty well if you’re using the right size bit collar (the red plastic rings that reduce the gap around your bit). It does like to dump chips below the table if you don’t close that gap (not always possible), which is annoying, but, I’m planning to build something to add dust collection below as well.

Hi …Great video…So how is the Bosch router table holding up since you’ve purchased it? Is the fence great?

@NorthwestCraftsman

2 жыл бұрын

Thanks! Glad you found it helpful! It’s lasted great! Full disclosure, I am not a full time shop by any means so I haven’t worked it as hard as it could be, but for a weekend hobbyist, it’s been awesome!

@juanmendoza7487

2 жыл бұрын

@@NorthwestCraftsman Awesome! Thanks for the feed back…Have a great one

How do you adjust the bit height above the table?

@NorthwestCraftsman

3 жыл бұрын

Hey Bryan! Great question! When the router is mounted, it’s upside down in the table. There is a small hole in the skid plate and router plate which allows access for an included hex key to turn the micro adjustment knob. It works great! Easy to adjust within a few thou.

HELP! I have the router GOF1600CE and I was wondering if I can use it with this table (my router is the plunge version) thank you in advance

@NorthwestCraftsman

2 жыл бұрын

Hey there! I’ve included a link to the manual which states all the compatible routers on page 15. I’m not seeing your model but double check me. Most plunge routers won’t fit under the table but there may be adapter plates out there that will allow it. Worst case scenario, you can make your own. RA1181 Manual pdf.lowes.com/productdocuments/33317c1b-1aec-45b5-9eae-46caa8e591db/08063444.pdf

Great video - much better than wading into the swarmy world of self-make. Looks like a good option compared to the endless $500+ offerings for a full table and confusing table top options. What are you using for dust vacuum?

@NorthwestCraftsman

3 жыл бұрын

Thanks! I’m using my Rigid shop vac with a dust deputy in between. Below are the links to the hardware I use, and a video on my dust collection. Blue Barrel: amzn.to/2HDpGlI Dust Deputy: amzn.to/3jBu6H0 Hose, 2.5”: amzn.to/37MqhMN Hose, 2.5” Adapters: amzn.to/2HJGO9z Video on my dust collector kzread.info/dash/bejne/lX6erMyco5yfdZc.html

Can you use this table with the Makita RT0700CX2J router ?

@NorthwestCraftsman

2 жыл бұрын

Doesn’t look like it’s compatible with this particular Makita. Check out page 15 of the manual though to confirm. RA1181 Manual pdf.lowes.com/productdocuments/33317c1b-1aec-45b5-9eae-46caa8e591db/08063444.pdf

The way he talks about Bosch hints to me that this is a sponsored video for Bosch ..

@NorthwestCraftsman

2 жыл бұрын

It isn’t 😊 I have been impressed by their tools though which may be why I sound like a fanboy 😂

What dust extraction you use?

@NorthwestCraftsman

2 жыл бұрын

Hey Steve! Currently I just use a shop vac hooked up to a dust deputy. You can find the links to all of the parts below: Dust Collection Parts Blue Barrel: amzn.to/3gKwfPS Dust Deputy: amzn.to/2PJooq4 Hose, 2.5”: amzn.to/3gLeqAp Hose, 2.5” Adapters: amzn.to/30MqFqJ

Did you figure out the shims? I’ve watched 3 videos now and no one mentions or follows through with them.

@NorthwestCraftsman

3 жыл бұрын

Tracie, thanks for the question! I haven't found a video on this router in particular but Fine Woodworking had an excellent video for how to use a router as a jointer in general. What would be different with our table is the 1/16" shims would go on the trailing side of the fence and set equal with the apex of the bit. This leaves the leading edge slightly offset, like in the video. I'll see if I can put together a video on using this specific table and shims as a jointer. Stay tuned! Fine Woodworking's Video kzread.info/dash/bejne/hXWE2MltaLbchrw.html

@kielherman3237

3 жыл бұрын

You put the shim behind the left side fence and it allows you to use the router table as a jointer.

Does this table have a router bit height adjustment feature?

@NorthwestCraftsman

8 ай бұрын

Sure does! When used in tandem with the 1617 EVSPK fixed base, there is a pass through with an Allen key for depth control

@mikeelizalde

8 ай бұрын

@@NorthwestCraftsman excellent! That’s what I figured. Thanks for letting me know. Looking forward to getting mine in a few days.

@NorthwestCraftsman

8 ай бұрын

Excited for you to get it! I love mine.

Can i use any model of router on this table?? What model you use??

@NorthwestCraftsman

3 жыл бұрын

Just about! The router plate has a ton of configurations to match different models. I use the Bosch 1617 and purchased the EVSPK which comes with both the plunge and fixed base for the router spindle. Honestly it’s my favorite tool in the shop. Here’s my video on it. New Bosch 1617 Router | Unboxing EVSPK Fixed & Plunge Combo kzread.info/dash/bejne/YmqMxc5rkbOnYcY.html

I’m thinking about mounting this table to a work bench without the plastics base, thoughts? Does this table have a router lift?

@NorthwestCraftsman

Жыл бұрын

That’s actually a great idea to give you more space to work. I don’t think it has a true lift, just access for the Bosch fixed base which as a bottom side adjustment.

@MDD1966

Жыл бұрын

@@NorthwestCraftsman I have a harbor freight Hercules plunge router that I want to add to a router table with a lift, any ideas? I have seen all of the router lift kits, but I want the slides and French to go with it without building

@NorthwestCraftsman

Жыл бұрын

You could always get a lift kit and mount it to a square piece of Aluminum or ply that fits in the top for this table.

Can you use different brand routers with this table ?

@NorthwestCraftsman

3 жыл бұрын

Sure can! Below is a link to the manual and page 14ish has a list of compatible routers. Manual pdf.lowes.com/operatingguides/000346353679_oper.pdf

@dylangardener1580

3 жыл бұрын

@@NorthwestCraftsman thank you

After 3 years did it perform well ?

@NorthwestCraftsman

8 ай бұрын

Great question! And yes! I use it regularly and still love it. Only complaint is I wish the table was bigger but that wasn’t the point originally.

is this thing new? cannot find it anywhere in germany

@NorthwestCraftsman

3 жыл бұрын

I don’t think it’s new, I’m seeing reviews of it back in 2015. Maybe a distribution/supply issue? Or they may be flushing it for a new model. Good luck finding one!