NESPRESSO O-ring | Step by step guide to change and prevent leaking
Тәжірибелік нұсқаулар және стиль
Hello guys
In This video I will show you how to resolve one of the most common problems with Nespresso machine leakage. It is necessary to change an O-ring which to be honest is not so easy to do. Therefore I decide to share with you the guide to do it. Enjoy!
Subscribe to my channel : @benassy69
Пікірлер: 263
Manufacturer: How overly complicated do you want disassembling your machine to be? Nespresso: Yes
@benassy69
Жыл бұрын
:)))
@pleb9622
Жыл бұрын
Exactly what I thought, I had a Tassimo before, and disassembly was a breeze
Thanks for sharing your knowledge - it's awesome to have someone repair things and not throw them away. Your videos are so easy to follow. Thank you
Thanks Mr.Adrian. I got this machine one week ago. Now i know how to DISASSEMBLY the machine. Thanks to you..
Bravo Adrian. Un video explicit pentru tot mapamondul. Respect
Great video. Couldn't have opened the machine without it. Thanks for posting!
Finally a decent video of reassembly! Thank you so much!
My Nespresso is old, but still works and just leaks. Your videos have prevented it from being landfill.
Very detailed, clear and professional! Thank you!
Excellent, would not have stood a chance without this, many thanks
Amazing. Now I will try to do all of this with my coffee machine. Thanks.
Thanks from Brazil my friend! Learned quite alot with you. Great job! Best regards!
That was very insightful. I've repaired my machine, using your instructions, thanks you
Excellent tutorial my friend. Thnaks a lot !
Excellent video mate. Thanks.
Thanks a lot for this very helpful tutorial. Lots of weird plastic sounds. But at the end, this evil machine works like a charm now. Cheers m8!
Thanks for this, took my own machine apart last night and (hopefully) have the correct size of O-Ring arriving today from Amazon! That was one hell of a job to disassemble - I'd never have been able to manage it without your easy-paced video!
@hardwaresecuritymodule
6 ай бұрын
I can't quite believe it, but it worked! First set of o-rings I got from Amazon were obviously too thin, so got the right one off ebay. One point I found tricky was putting the nozzle bit back onto the springs - I thought I had it on, but it wouldn't compress and I took it off and did it again .... apart from that, re-assembly is quite simple. Thanks again!
@cristinademeo2727
5 ай бұрын
can you please share the ebay link or the dimensions of the ring? Thank you!@@hardwaresecuritymodule
@benassy69
5 ай бұрын
@cristinademeo2727 I have a video on my channel addresing exactly this.
Very very informative video, all the trick and tip explain in every steps, good job!, subscribed!
Very nice explained video. Thank you
Thanks for sharing, it helped me a lot!
Thanks! you saved my morning !
Thanks a lot, very clearly explained.
Adrian, a Big thanks for your video 👍👏👏🇬🇧
Thank you, your video was very helpful, I have to do exactly the same with my Nesspresso.
Was going to buy a new machine and this video saved me 70€. Replacement o-ring= 0.25€ and 1hour of pure joy. All the best for you!
@benassy69
Жыл бұрын
Glad it was usefull!
@javidiaz6272
7 ай бұрын
Ohh great,but I don't know where can I buy this o ring. I live in Spain
@arraiolos
7 ай бұрын
@@javidiaz6272 any drug store should have it (tools shop)
@benassy69
7 ай бұрын
Ebay. com sear h for "Nespresso O-ring"
There are two o-rings. This one behind the pod, the dimensions for this o-ring is 31.5mm (inside diameter) x 3mm. There is another tiny o-ring inside the boiler unit. The plastic and metal parts can be separated by twisting clockwise (it requires some force). Inside is a black cone with a small o-ring on top. The dimensions of this one is 5mm (inside diameter) x 2mm.
@benassy69
Жыл бұрын
Hi Ben. I know I had encountered a couple of times this issue with the small oring behind the boiler. I noticed that if the small oring is the issue is usually water present in the pump chamber and a lot of limescale on the external wall of the boiler. The big problem is that the boiler is extremely hard to remove from the plastic housing in order to have access to the oring and change it.
@oldskoolflash1
Жыл бұрын
Yes exactly. I actually found the plastic on mine quite easy to remove, it was like a bayonet lightbulb fixing. I just griped the boiler with gloves and gave a little twist clockwise. It was about the only easy thing on this bloody job so far! I hate it when manufacturers just clip stuff together like this. Thanks for your videos though, they were very helpful in my moment of need!
@elineweg2452
Жыл бұрын
Hi Ben, which one should be replaced if the water is coming out where the used pods fall? In stead of coming out the spout?
@oldskoolflash1
Жыл бұрын
@@elineweg2452 Hi Eline, I'm not sure I understand where the water is coming out? For me the water was leaking between the plastic and the boiler. I tried replacing o-rings and that didn't work. I ended up replacing the whole boiler unit (which cost about £27). Finally, this fixed it for me. This has been the most painful repair I have ever done!
@elineweg2452
Жыл бұрын
@@oldskoolflash1 Ohhh okay then it is a different issue. With me the water falls into that black container that collects the pods afterwards.
Muito bom trabalho consegui arranjar a minha máquina graças à sua boa e profissional explicação...muito obrigado. Bom trabalho.
Thanks for sharing your knowledge -
Grazie per il video, assolutamente di aiuto, sei veramente bravo, buon lavoro.
Great video, thanks.
Thanks for the magnificent video. I had already disassembled the coffee maker on a previous occasion (it has been so long ago that I no longer remember the fault although I was able to fix it) But this time, due to a water leak, I was not able to get to the problem until I found your video, detailed and efficient. The pity is that it still leaks slightly after changing the O-ring. I have already read in the comments that there is another small O-ring on the boiler. Now I don't know if I'll try it again. The truth is that I don't use it much. The repair was rather a challenge. Thank you anyway.
@fotoytall
2 ай бұрын
I write from Spain with the help of Google Translate. I'm sorry if there are errors.
Thanks you saved my machine!!
Bom dia obrigada pelo vídeo foi o único q achei ensinando a montar parabéns, eu tava tendo dificuldades pra montar aqui um desses e vc ensina muito bem,mesmo com as legendas é muito bem explicado obrigado, vc ganhou mais 1 escrito em seu canal
@sergioamaro1706
Жыл бұрын
Minha cafeteira esta co vazamento. Será que se trocar a borracha de vedação, como mostra o vídeo, o defeito acaba?
I solved the water problem myself of my Le cube machine thanks to your video. Its an old machine but good quality,,the next problem is now,,one of the buttom doesn t work but light is still working
@haythemshady
Жыл бұрын
How can repair (the water problem)
Thanks for a very good video, do you have a video for Krups nx250 o ring replacement?
Excelente!👍🙏👏👏👏👏
Merci pour votre explication qui m'aide plus de résoudre ce type de problème.
Consegui salvar mais uma maquina graças a sua ajuda, muito bom seu video. Muito obrigado
good job!!!!!
thank you so much bro 👍
Obrigado, ajudou muito seu vídeo 👏👏
Hello Adrian. Really great video. Can you please advise what size oring you used? Is it std nitrile or silicone....thanks
Great video, thank you. I have DeLonghi nespresso EN80 and it has exactly the same construction.
@lillyminutolo5716
Жыл бұрын
Where to buy this o ring?
@valsanich
Жыл бұрын
@@lillyminutolo5716 deLongi sells a repair kit with spare parts.
@lillyminutolo5716
Жыл бұрын
@@valsanich link?
@valsanich
Жыл бұрын
@@lillyminutolo5716 google it. YT doesn’t allow links
Thank you.. soooo much.
Thanks Adrian for the tutorials. I have an Esenza Mini. When I insert the capsule and turn on the machine, the hot water comes out of the opening of the capsule. It should be noted that the front part with the holes is clean. Any idea what the problem is?
Thank you man
Merci, grâce à vos instructions, j'ai reussi en quelques minutes à ouvrir la machine. C'est vrai qu'il ne faut pas hésiter à forcer un peu, ça ne casse pas.
@cptrasko
5 ай бұрын
Bonjour, vous avez trouvé le joint en question ? Pouvez-vous me donner le lien, s'il vous plait. Merci par avance. 😊
@jpaparicio4066
5 ай бұрын
@@cptraskobonjour, j'avais mis un joint torique trouvé dans un magasin de bricolage.
O vídeo muito explicativo. Muito bom, me ajudou muito 👍
Hi Adrian, many thanks for the detailed repair procedure. Excellent work! What are the exact O-rind dimensions to purchase before attempting to repair? Internal diameter and thickness?
Great video HOWEVER, o rings out of there are made of (often) unspecified materials that may not be safe for food contact. Silicone is typically the best choice but all I can find is either Nitrile or fluorocarbon rubber. Krups has done an amazing job in preventing repair shops or dyis to find small parts so I have no idea what material the original o-ring is made of.
Please can you tell me if there is a component that the nylon pin with the small spring fits into? Does it just fit into the star shaped aperture in the heater unit or is there a piece that I am missing? Hopefully not!
Where did you purchase your parts from? I am looking for a CITIZ auto primer…
Hello Adrian! Where can i find a replacement O-ring from inside the brewing mecanism of a Citiz & Milk?? Thanks!
Hi Adrian bought some types of seals from china and world fluids, I was wondering what type of piston o ring you use?
You are very strong 👏
@benassy69
5 ай бұрын
😆
You know those very brittle clips you mentioned? ... Which part should I order if one of them snapped?
Adrian thank you so much for the tutorials, much appreciated! My Inissia leaks a lot from the spout (nozzle) where the coffee comes from. Any idea if it's fixable?
@benassy69
Жыл бұрын
It is normal to leak some drops after you finish the brew. It's actually cleaning the pod chamber.
Very good! I will save my machine and the planet... but where to find the o-ring? Thank you for your video. Very clear.
@benassy69
Жыл бұрын
Hi. You can find it on ebay. Search for Nespresso oring. It should have 38mm outer diameter. And 3 mm thick.
Hey! Love that you uploaded this video. I followed it exactly and everything worked exactly as you showed and I replaced the o-ring. But it leaks more now than it did before, this time a new leak from the water tank junction. What might have happened for me to mess this up? It didn't leak from there before!
@benassy69
10 ай бұрын
Hi. You might have positioned the water tank sear faulty or a joint is not correctly set. Try reposition it correctly
@mw55309
10 ай бұрын
@@benassy69 can you post a picture of rust it's supposed to look like? I'm worried I might be missing a part
bravooooooooooooooooooooooooo
Hi, My Magimix Nespresso machine is stuck in descale mode. I have tried all recommended reset options and spoken to Nespresso. Any suggestions on a fix before I scrap it please
ขอบคุณครับ
Mine (same as your model) has a low caudal of water. It does not look like is spilling out water. Just a weak stream. I tried to clean the capsule hole with a toothbrush and apparently got a little better but still not right. How could I fix it?
Fantastic video, thanks. How often do I need to replace the o rings if I use 2 pods a day?
@benassy69
Жыл бұрын
Maybe in 2 years from now...
hi thanks for the vid i replace the O ring 31/37/3 and i have still the same leak any idee ?
No 17:28 minuto q vc amostra a parte encaixada ,no meu aqui não tá encaixando fica uma pequena brexa entre as partes já apertei ,soltei várias vezes e seguindo seu vídeo mesmo assim fica essa brexa ,quando eu desmontei não tinha reparado se tinha já essa brexa ali
Would be helpful to give the size etc. on the O ring(s) so we can try to find them. Also Metric or Inch
I just bought a new one from Nespresso and a fair bit of water winds up in the tray with each coffee. The recycling company has already picked up the cardboard box and packing material so it would be a pain to ship it anywhere but this seems quite annoying to replace the O rings myself. Thanks for the video though.
where do you buy/get the parts?
Dear Adrian, thank you for all your excellent videos. Ik want to know WHERE you can buy the O-rings for the nespresso machines (stop leaking), thank you Edward (netherlands)
@benassy69
Жыл бұрын
Hello Edward, thank you. In some countries you can find it on Amazon but to be sure you can find it on ebay. Search for Nespresso oring on ebay sould be a 38 mm oring.
Hi, Thanks for the video, i managed to follow the instructions but the O ring was in great condition. We then tried the machine without the trays in place and surprisingly all was good. The leak happens when pulling the handle to discard the old pod, that's when a ton of water comes out (well, about 10 or 15 mls). Any idea on the issue, maybe as we are not using proper nespresso pods, we are using compostable?
@benassy69
11 ай бұрын
It is normal to have residual water in the pot chamber. If you don't have any leaks during the brewing process than it is not a problem with the machine. Could be from the pods itself.
TKS
he must be Nespresso Co. as engineer worker? /? very interesting to see how he can fix the difficult machine
Buongiorno! Grazie per il tutorial, io ho comprato le guarnizioni di ricambio su Ebay, già che c'ero le ho cambiate tutte e con poco più di 5€ ho risolto tutti i problemi
Mulțumesc for another great video, Adrian. Beyond the O-ring, my Magimix machine has a flat metal ring, which appears to be broken. Can that also cause leakage? Can share pics if required.
@benassy69
Ай бұрын
That metal plat ring is purely decorative. The capsule make a tight seal on the flat surface on which the aluminium foil is placed. Make sure you use original pods aftermarket ones are leaking du e to lack of a silicone seal. Take a look on one of my Last videos where I explain this....
@GerlandoAlletto
Ай бұрын
@@benassy69thanks, Adrian. I’ll ignore the metal ring and buy the O-ring and replace it. Hope it solves the leakage.
Bonjour le joint ou je peux le trouver sur le net j'ai trouvé 42mm celui-là il fait 37mm je trouve pas
What are you guys using to wash the parts? I submerged everything in warm water with dishwasher detergent and brushed with an old toothbrush but still some areas are dirty. How about vinegar? Anyone tried it? Thanks!
Does anyone know where to find a tutorial for same problem for the Nespresso Essenza Mini
Many many thx Adrián for your video! I safed mi Nespresso Inissia Krups 😍😍 Have you video for pump problem (not draw water from. The thank) for the same machine? Thx
@benassy69
Жыл бұрын
Hi Giulio. I have a video on how to disaasamble and clean/ repair the pump.
@GiuMon1972
Жыл бұрын
@@benassy69 In your Channel I see only a video for pump repair but for another model of Nespresso 😞
@benassy69
Жыл бұрын
The pumps are the same for all coffee machines regardless of the brand.
@GiuMon1972
Жыл бұрын
@@benassy69 Thanks for the information. I can update you on my machine: unfortunately the water leak from underneath is still present and I can tell you what the problem could be with this. One of the two plastic hooks that hold the piston hardens with the heat not allowing the piston to remain attached to the base as it should, for this reason the gasket descends favoring the escape of the water. The plastic hooks become very delicate having hardened so much that it is easy to break them.
Tank toi frère
@benassy69
Жыл бұрын
Avec plaisir
Thanks
@pjburnhill
Жыл бұрын
Managed to fix our machine and it's back to being near brand new! Thanks for the video.
Is it a good machine?
Adrian, where can I buy the o-rings? I can't find a supplier. Maybe Ali-Express?
@benassy69
2 ай бұрын
eBay.com
where can I buy de O-ring?
Very good tutorial, thank you very much. Could you tell me the size of the o-ring? Or the link where to buy it. Best regards
@benassy69
Жыл бұрын
Hello. ~34 mm interior diameter. 3mm thickness.
@joseab
Жыл бұрын
@@benassy69Thank you very much for the reply. I was able to disassemble the piston and I measured the rubber gasket and it gave me an external diameter of 37mm and a section of 3mm, from which it can be deduced that the internal diameter should be 31mm?? You leave me in doubt. No problem, and thank you very much because I have learned a lot from your tutorials.
@javidiaz6272
7 ай бұрын
I don't know what size buying too
Thank you so much Adrian , but where I can buy those o rings ?
@benassy69
6 ай бұрын
Take a look on my last video on the channel.
Where are you located?
Hi, if you break one of the clips holding the o ring what can you do? Any ideas?
@catialopes9428
3 ай бұрын
I have broken the two clips... Can it be fixed or I just have to buy a new machine?
mine lick only for 20 seconds after the erogation. is that the case?
Excelente técnica e conhecimento do aparelho. Por gentileza, façam um vídeo traduzido para o português (Brasil). Obrigado.
@alancariglino5593
9 ай бұрын
Ciao se ti può interessare ci sono i sottotitoli tradotti nella tua lingua apri impostazioni e nella lista trovi la tua lingua saluti
The size of the original o-ring please... Inside, diameter, if you can. 31.5mm (inside diameter) x 3mm it is good ? Thanks a lot
@benassy69
Жыл бұрын
Hello. ~34 mm interior diameter. 3mm thickness.
@philippepoirier552
Жыл бұрын
@@benassy69 Thanks a lot
After following your video to replace the o ring my machine won't stop flashing the lights I can't do anything. Any idea on what's wrong? Was working fine before
@benassy69
Жыл бұрын
Take a look if you fitted the buttons correctly. Sounds like a always pushed button.
thk
Where did you find the correct O ring which is actually shaped as a D ring? Having trouble finding this.
@javidiaz6272
7 ай бұрын
Me too
Hi Adrian. Perhaps you can help with my problem. My INissia works fine, but the lever has started to jump up once the pump is working. The only way to have it work is to press down and force the lever to stay down. The lever does not open when there is no capsule in the machine and the pump is working. Any insight you can give me? Thank you very much.
@benassy69
11 ай бұрын
Hi I only imagine that your brewing mechanism is worn out and it does snap shut one a capsule is inserted. You have to open it and see what joint is causing this. It is not a usual problem of this units.
@davidweinstein2620
11 ай бұрын
@@benassy69 Thank you very much. From what I saw, bend the basket for used capsules, there should be a unit that snaps in and serves as a lock to the lever. I'll try to take it out. Can I find a replacement in the market?
@benassy69
11 ай бұрын
Yes. You can buy the full brewing head but is somehow expensive for what it is. You can search instead for a defective unit and just swap it.
@davidweinstein2620
11 ай бұрын
@@benassy69 Thanks. I'll pursue this.
Where to buy the big o ring ? The one in the exit of the brewing head?
@benassy69
6 ай бұрын
Hi check out my last video on my channel. I am addressing this exact topic.
Vous avez trouvé où le joint
My leak is coming from under the machine. Water is hot and it does fill 1/2 cup, but takes almost 3\4 of tank to do so. I am not sure if it's a ring or something else. Do you think it's fixable?
@benassy69
Жыл бұрын
You have a clogged diffuser plate. I have a video on how to address this issue
@marinastar8120
Жыл бұрын
@@benassy69 Thank you, I will check it out
@geffridamer9798
Жыл бұрын
@@benassy69 can you link the video? I have the same problem but i don't find the video on your channel
@benassy69
Жыл бұрын
kzread.info/dash/bejne/gIih0ZujqZTKktY.html
@geffridamer9798
Жыл бұрын
@@benassy69 thank you for the video, unfortunately I have already cleaned that part so that's not the problem
Replaced the oring to a new one 32x38 but it still leaking water into the drip tray quite heavily, no change to prior seal. any ideas? :)
@haythemshady
Жыл бұрын
Clean it
@greatdane3343
7 ай бұрын
Change the small o-ring in the boiler chamber area.
Hi, thanks a lot for the video. One question: where can I find the o-ring? I was looking for on several websites without any sucess.
@benassy69
Жыл бұрын
Hi you can find it on ebay. Search for Nespresso Oring 38mm wide 3 mm thick
Bun tutorialul. Cam la cat timp se uzeaza acest o-ring?
@benassy69
Жыл бұрын
Salut Lucian cam la 2 ani de folosire , din experiența.
@lucian9582
Жыл бұрын
@@benassy69 Deci dimensiunile sunt standard la toate aparatele ? Incerc sa gasesc pe aliexpress dar nu sunt sigur ce sa iau de aici: www.aliexpress.us/item/1005001460518803.html?spm=a2g0o.productlist.0.0.1aa97868bFShUO&algo_pvid=f1d40a40-4eb6-4da6-ac54-e47c2aefbe93&algo_exp_id=f1d40a40-4eb6-4da6-ac54-e47c2aefbe93-5&pdp_ext_f=%7B%22sku_id%22%3A%2212000025698341262%22%7D&pdp_npi=2%40dis%21USD%211.5%211.27%21%21%21%21%21%402100bddd16658229646974421e23b6%2112000025698341262%21sea&curPageLogUid=8DcZsqaIHT9B&gatewayAdapt=4itemAdapt
@benassy69
Жыл бұрын
Da dimensiunile sunt identice la toate aparatele. Recomandarea mea e să cauți un set de oringuri universale că se potrivesc și acolo ai o grămadă de dimensiuni.