Still an awesome video - solved my problem. More importantly, uses the best music track ever, none of that wack electronica rave junk that usually gets pumped out. Kudos.

Now just wire in a variable speed controller and could be used on a camera slider?

Finally the first tutorial with actual code that works! I've been through a number of them where the code ultimately fails. Thanks!

Thanks for the video! I have an Nema 17 hooked up to a L298n and an Arduino. I have no issues operating it, but I'm having problems powering it. If I use a 5v 1a supply, it works but torque is low. If I use a 12v 2a supply, the torque is great, but the L298n pulses ever second or so which sends power to the motor. It doesnt appear to actually turn the motor, but it makes a buzzing noise which is VERY annoying. Do you know why I'm getting this pulsing from the driver?

If I want to use the joystick to do real-time control, what should I do?

Thank you for this helpful informations! Please let me ask a typical "Beginner-Question": I want to include a Potentiometer or 2 Switches (clockwise/counterclockwise) for controlling the NEMA17. How is the best way to integrate/connect? Have I to Change something in the Sketch? Thank you for your helpful answer.

Kindly tell me how to program stepper motor to make any specific number of revolution in clockwise direction and then the same number of revolution in anticlockwise direction continuously. And also how can I vary the speed of revolution. All the programming I am getting is about single revolution in clockwise and single in anticlockwise direction.

Hello, my L298 gets tremendously hot as soon as connected to the Pins 8,9, 10 and 11 of the Arduino board. I use L298N with a Nema 17 45Ncm 1.5A 12V and identic wiring as shown by you. This has quite some effect on the step motor after 30secs that get noisy then stops working after 30secs. Thank you for any hint.

@RonAdamsky

3 жыл бұрын

Most of Nema17 work only with new drivers : A4988 , Tmc2208.

@ghanshyamc463

3 жыл бұрын

@@RonAdamsky I have the same overheating issue. Will using the a4988 solve it??

@RonAdamsky

3 жыл бұрын

Yes I tried with TB6600 and works great.With L298 Nema17 don' t move at all.My Nema17 motors have only 2ohm resistance of coil.

Great video........Check out my ps2 controlled car I used a l298n but the motor over heats fast any advice

Could you provide the parts used to incorporate the belt driven linear actuator?

How to determine A+&A-&B+&B- mine is just vibrate and not moving. Nema 17 5.6kg motor driver and connected similar to you. Power supply 2amp 5 volt please help

Sir... The link i cant access.. i really i need this sketch T T

I am sorry, i am wondering which model of a 3D-Printer we are seeing in the Video .

Hy nice

I'm sorry but you can apply ~35V on the 12V input? what?

has anyone gotten this L298N+Nema 17 to work with ESPHome or Tasmota? if so, could you please show the wiring diagram as well as the codes?

I used an arduino i previously had used to play the game of thrones theme song on a piezo buzzer and when i turned it all on the motor started humming the theme song

it is possible to control microsteping?

شكرا انت فنانة

Did not work for me ! I think the newer motors need A4988 .

Молодец милашка

Pretty limited use project as it requires two power sources (5V and 12V).

Unable to find the sketch. link is broken

I want use wemos instead of arduino

LINK SKETCH eror.

Nice

Hi I needed some help with ardino sketching. I just started a month ago. I need some help with a project that i am working on.

Not for low resistance stepper motors Nema17 , HS4401 doesn't work.

@kudin8082

3 жыл бұрын

for this stepper motor, what power supply need to use.?

How to connect 3 of L298's (3 axis xyz) with Arduino for CNC purpose? Is it possible?

@atihrot755

Жыл бұрын

Je to možné ale treba zvlášt 3 ks ovládačov na každý krokový motor.

what type of this nema?

thanks i like ittt

Thank you

thanx it is nice

I'm using 5A 12V power source and 1.68A stepping motors, but they are only vibrating, tried all wires combinations, do you have an idea to make it work ? :(

@nizarworld2020

6 жыл бұрын

change wiring.coils are not in the same line .but across the board. i had same exp . now it working fine

@asimov741

6 жыл бұрын

Well i fixed it, that wasn't wiring but Arduino D8 which was in HIGH whatever I would program 🤔

@nizarworld2020

6 жыл бұрын

will u pls reply to my doubts

@martienrurenga772

5 жыл бұрын

hi, i'm having the same exact problem, could you maybe tell me how you fixed it?

My stepper motor is vibrating but the shaft not rotating could u help me out

@slathian1223

4 жыл бұрын

I had this issue too. A couple things you could try: make sure the polarity is correct on you connections. Use a multimeter to see the resistance it should be .009 ohms. If that doesn't work disconnect your ground wire from your power supply and the arduino and make sure your PSU outputs a minimum of 3.5 amps. This will be 1.7 amps per motor phase.

@RonAdamsky

3 жыл бұрын

Try with another drivers ie. A4988 or TMC.

@kudin8082

3 жыл бұрын

@@slathian1223 what power supply I should use for stepper motor nema17 hs4401..?

parabens. top obrigado

Continously? Or Motor Will Stop After Sketch?

@MakerTutor101

5 жыл бұрын

continuously. dirStep = 1 to left , dirStep = 1 to right if( stepCount > 500){ stepCount = 0; if( dirStep == 1) dirStep = -1; else dirStep = 1; }

May I know the holding torque of this motor?

@hemanthnarayan373

4 жыл бұрын

www.amazon.com/STEPPERONLINE-Stepper-Bipolar-Connector-compatible/dp/B00PNEQKC0/ref=sr_1_2?dchild=1&keywords=Nema+17&qid=1590211554&sr=8-2 You can find the user manual in the link;

my l298n gets very hot after just 30s of motor spinning, and i cant figure why :( i have a NEMA 17HS8401S same driver module, and a power supply 12v 5A motor spins ok

@ivang.7526

5 жыл бұрын

Dude, with the l298n the max is 2A

@Andrew-gx3ps

5 жыл бұрын

Still struggling? I can help you out

@Dr.Sarkar

4 жыл бұрын

@@Andrew-gx3ps I have the same problem, I have nema23 with l298n, the l298n gets very extremely hot after a few seconds..

@memahrez

4 жыл бұрын

@@Dr.Sarkar ln298 is rated for 2amps max

@Andrew-gx3ps

4 жыл бұрын

@@Dr.Sarkar Hi, If you're using a PS that is capable of supplying more than the 2A max of L298N, you can still use the power supply. What you'll need to do to make this work and not overheat/blow your L298n is to send a PWM signal to the enable pins on the H-Bridge. Start with a low duty cycle and increase from there. If youre driving 2 phases of a stepper with the H-Bridge, set the PWM to be the same for both enA and enB. Sending a PWM signal to the enable pins is used to limit the current passing through your L298N module. If you are currently setting the enable pins to HIGH, your essentially setting up a 100% duty cycle thus allowing the full current to pass through. If your current is not limited by your PS or by PWM, current will pass through and it is defined by Ohm's Law(ignoring induction of the motor). I hope this helps you. Have fun :)

so nice thanks for helping .....

Как к нему подцепить мотор сканера чтоб играть музыку?

Coding please

no picture, kein Bild

thank god for the mute button

Nema ke wires l298n ke konse port pe jayege like in 1,2,3,4 kon tera bap batayega kya, agar video dalni to thik se dal

Nothing informative