My Water Heater Won't Drain [Fix It With 3 Easy Steps]
Тәжірибелік нұсқаулар және стиль
Is your water heater not draining? Here are 3 simple steps to get your water heater to flow. First I'll show you how to drain your water heater. If this process doesn’t work I’ll show you a couple tricks that will make stubborn water heaters drain. Lastly I will explain why the water heater won’t drain.
✅ Live in San Diego County? We Can Help: quickwaterheater.com
Link to How to Make a Proper Drain Valve quickwaterheater.com/faq/#156...
Here is a summary of your steps:
1. Attach garden hose to drain valve
2. open valve let water flow for 60 sections. it should flow freely. If you skip this step the water heater most likely will not drain.
3. Shut off water at shut off valve
4. Open hot water fixture or undo a supply line
1. show straw example
5. drain water heater
6. If you live in San Diego and need help with a water heater replacement or repair please click the link below to see our prices and schedule an appointment right from our website.
Пікірлер: 402
I had the same plugged drain valve on my 11 year old 649DORT Reliance 40-Gallon Electric Water Heater. Mostly caused by the complete degradation and totally corrosion of the entire 29" Inches OEM Anode Rod, as it was impossible for me to drain the water tank that was equipped with a plastic drain spout, but I could not introduce a screwdriver on the opening, as the outlet connection to hook up the water drain hose, was at a 90 degrees from the straight pipe coming out of the heater tank. Thus the method to unplug it I use was by using my air compressor with an air hose an air blow gun that I inserted on the end of the drain spout, using about 90psi of air pressure I also I opened the hot water safety relief valve and as I was blowing air into the tank I could hear a weak air hissing sound into the tank that eventually sound like and explosion that pushed out the debris plugging the drain spout and soon after water was draining out the spout and was able to completely drain the entire tank, then I open the cold water and continually rinsing the tank while the water was coming out in a milky color with small particles of the corroded aluminum material and other mineral salts? until the water was clear of debris and clean... I then installed a new Aluminum Anode Rod.. I try to remove the plastic drain spout, to replace it with a metal one that had a larger draining orifice, but the plastic one was too tight and I was afraid that it could break apart if I forced it out, and then I would have even a worst case scenario there, so I leave it like that.
I was stuck on this. Thankyou for uploading!
Very useful tips and recommendations. Thank you.
Thanks! None of the other videos I watched mention “airlock,” which of course is the problem I had. Very helpful!
@quickwaterheaterfiltration5292
4 жыл бұрын
cmundale sweet. Glad I was able to help you understand the mechanics of why your water heater wasn’t draining.
@yesreally7438
4 жыл бұрын
Same here :)
@rosemarybaker
3 жыл бұрын
I agree! This is the first time it’s been addressed in all the videos I personally have seen. It makes complete sense and I’m so glad I know now. I have horrible hard water. The previous owner never cleaned it. So..... I’ve changed the element 3 times in 6 months. Water softening unit isn’t an option for me yet.
Man, thanks so much for the video. My tank was definitely jammed up with sediment. I wouldn’t have thought to try to flush it out using the pressure. Thanks again!!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad we could help
Best video I've seen on this process yet.. Only one that solves the "I waited too long"
@quickwaterheaterfiltration5292
3 жыл бұрын
Thank you!
Your tips and points answered all my questions about why and what to do about my slow draining tank. God bless you and all who take the time to put together videos and the like to help others out.
I made a Hot water heater drain valve per your description. I could not prevent the hose from leaking! I found by watching another DYI KZread video that you need to have a garden hose adapter for the part that the hose attaches to. It is a 3/4 inch MHT X 3/4 inch MIP which is actually called a garden hose adapter.
Thank you so much! My water heater seemed to be working fine but only light warm water was coming out. I watched someone else’s video on how to drain my water heater and it was a no go! But your video worked like magic for step 2 for me. Thank you again!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it helped!
I was having problems with draining and I’m glad I found this video. Unfortunately I had a lot of sediment so I had to do the last option and that did the job. I may have missed a step on creating a vacuum so I did splash myself a bit. Thank you
Worked like a charm, thanks from Texas.
Great video with clear and concise instruction. Reduced drain time immensely and no video prior mentioned releasing the pressure at the valve. Kudos to you! Had to replace the elements and now fingers are crossed for hot water!
I've done a lot of water heaters in my life but I learned new tricks everyday and I thank you for being thorough and very explanatory dig your video keep it up I just subscribed thanks again and blessings
So incredibly helpful. Thank you!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it helped!
Thank you! My water heater wouldn't drain, so I used your first suggestion of opening the cold water valve while everything was hooked up & bam! It went right out.
Thanks for this video totally helped with draining my old hot water heater👍🏻
Thank you for taking the time to post this excellent instruction video.
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful!
Awesome tips... Thanks sooo much! Never knew water heaters needed to be drained... that 3/4" drain will help bunches... the peeps are Home Depot were blown away by what I was doing lol!!!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful!
Great video. And I could listen to your voice all day!
@quickwaterheaterfiltration5292
3 жыл бұрын
😊 thanks
Awesome video, thanks! I followed all of your instructions on pulling a vacuum on the tank and it worked like a champ. I had the new valve ready to install and I probably didn't lose any more than one cup of (nasty) water from the hot water heater. It was taking about 2-3 hours to drain my hot water heater. With the new 3/4" gate valve, it takes about 15 minutes. Thanks again for the advice.
@quickwaterheaterfiltration5292
2 жыл бұрын
That's awesome! Glad it helped!
@swiz22
2 жыл бұрын
So when creating a vacuum, you want no air in the tank, right? Like in the prior step he opened the hot water supply to let air in…when trying to put vacuum back in, I have to reattach the water supply, right?
@princescottygustafski5331
Жыл бұрын
I don't believe it's ever worthwhile or advantageous to ever use a gate value. 👎 It is always best to use a BALL VALVE! 👍👍👍
That was one hell of a good learning.thank you.
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad you enjoyed it
Thank you for this! Just used your vid to troubleshoot & successfully drain water heater! :)
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it helped!
Thank you This really helped me a lot because my water would not drain out of the tank Thank you so much for making this video ❤❤❤
You answered 6 of my 5 questions, thanks so much.
@quickwaterheaterfiltration5292
3 жыл бұрын
Excellent!
@streetsharksbedfordpoint6.933
3 ай бұрын
@@quickwaterheaterfiltration5292is it normal if the bottom of my water heater is hot sometimes?
Thank you! I also found the pressure relief valve creating a vacuum that was slowing the draining of the tank. Opened it up and boom, success
@xenomorph7299
3 жыл бұрын
same for me that worked
@quickwaterheaterfiltration5292
3 жыл бұрын
That's great!
@bradleyrussell1973
3 жыл бұрын
Same effect as opening a valve.
Thank you for a great video, very professional and helpful.
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful!
Excellent video. Thank you. I had to open the supply line . Worked like a charm.
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful and worked for you!
Great tips! The ball valve solved my problem!
Great video! I live in the country and I do not use anode rods. Our hot water and the anode rode combined make for an eggy smell. No rod, no smell BUT as per the video, nothing for the minerals to attack. My absolute favourite part of the video is the tip on replacing the outlet valve with a 3/4" ball valve. Brilliant! Open and flush. Keep up the good work!
@quickwaterheaterfiltration5292
3 жыл бұрын
Thank you!
@Rhinomods
Жыл бұрын
I am not a professional but are there not different rods types that will keep from making the egg smell? I thought I had read that if you replace standard magnesium rod with a zinc anode it will not react with bacteria that causes the egg smell... an idea to look into?
That fixed it. Now it is draining. Thank you.
@quickwaterheaterfiltration5292
4 жыл бұрын
David Richardson awesome. I’m glad I could help you
This video was incredibly helpful. Thanks!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful!
The first step got mine draining, thank you!!!
Your detail for the homemade drain valve saved the weekend; thank you for sharing! After removing the OEM valve I saw that it was plugged and discovered why none of the other tricks would work. Now, when I need to replace the water heater I'll install one of these valves during installation.
@quickwaterheaterfiltration5292
4 жыл бұрын
Brian Fletcher awesome. I’m glad the video was able to help you.
Thank you, really helpful.
@quickwaterheaterfiltration5292
4 жыл бұрын
I’m glad it worked for you. Thank you for commenting.
Thank you! Very successful on the tips! You saved me 530$
@quickwaterheaterfiltration5292
3 жыл бұрын
That's wonderful!
I have a water heater that started leaking and would not drain. I just watched your video, tried #2 and replaced the cheesy OEM valve and it worked like a charm. Thanks!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it worked for you!
Thank you for the tips. Lot of good info!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful!
From Texas ! Great Video ! Thank yall so much , very informative !
This saved my butt! Thank you!
@quickwaterheaterfiltration5292
4 жыл бұрын
William Bluem I am happy I was able to help.
This was just what I needed - thanks alot. Worked like a champ.😀
This was a great help. Thank you.
Good, really good video. I was ready to put a tap in like a maple tree. My Bradford White has a pressure valve on the side, so instead of taking off the one of the supply lines, I opened up the pressure valve and voila, water started flowing. Thanks so much for your help.
Thank you for this video. I couldn’t figure out why my tank wasn’t draining.
The MOST informative video. Thank you!
@quickwaterheaterfiltration5292
5 ай бұрын
You're very welcome!
Thank you so much for your help , I really appreciate it .
@quickwaterheaterfiltration5292
3 жыл бұрын
Happy to help
I thought there was a vacuum keeping my water heater from draining, and your advise was helped me solve the problem. Thanks for such a well-made video! And BTW, I had a plastic Rheem drain valve and I replaced it with a brass one with no problems, so at least in my case, I wasn't screwed.
@GhostGL
4 жыл бұрын
I've got a plastic valve too. Reliance water heater. How'd you go about replacing it with a brass valve?
@riddlemechris
4 жыл бұрын
@@GhostGL the video explains around 6:25
Watching from Nigeria…. This is really helpful and expository
Great video! Thanks!
Great information and video. Mine would not drain...hours and just a dribble. I changed out the valve and bingo, done in a flash. Got some orange water for a while but drained the tank again and ran more through the pipes and it's clearing up. Thanks.
@quickwaterheaterfiltration5292
4 жыл бұрын
Sweet. Yeah it’s a must to let air in the tank and get a drain valve that can pass chunks through.
So glad I found this video. Still sprayed myself but I don’t even care. Had a wall of sediment in there. AZ ground water is lousy with minerals. Thank you so much.
I tried three different ways to unclog a hot water tank and they all failed, until I found this video that showed how to increase the air pressure pushing down on the water in the tank and bingo, the drain started to run and the tank emptied! Great video!
@quickwaterheaterfiltration5292
5 ай бұрын
Glad it helped
It's draining now!! Followed your 1rst step using pressure from the incoming water valve. Did that over and over. Probably 5 or 6 times. Along with opening a hot water facet. And then the magic happend! Draining as I type. Thank you so much!!
@quickwaterheaterfiltration5292
6 ай бұрын
Magica!
Good job man 👍👍🤛
Excellent info! I had exactly this problem -- sediment had chocked the drain valve. I had no idea what to do until I saw this video. Keep the pressure on (water inlet open) to push out the sediment through the drain valve. Worked -- thanks!
Old plumber's trick if you have an air compressor... Shut off hot and cold water pipes attached to water heater. make an adapter with a 3/4" male adapter to fit into relief valve opening and have a schrader valve (think bicycle tire valve) connector on the other side. Use an air chuck hooked up to your air compressor to force air into your water heater tank and water out the bottom. If you have a lot of scale build up in the bottom of the tank, this pressurized approach will force it out the faucet on the bottom of the tank. Also drains it a lot faster than gravity feed. If you have an electric water heater and the sediment is real bad you can remove the bottom element and finagle a scrapper out of S-cleat to draw the sediment to the opening.
@jessm1638
2 жыл бұрын
Love that idea for the electric water heater… thanks!
Thank you! Your advice worked. We had to open a faucet on the floor above the water heater.
Worked great, thank you
The coupling on top worked. Thanks did the clear explanation.
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it helped you!
So helpful! Thank you so much.
Thanks so much for this video. I made a custom drain valve per your instructions and it worked! Before that, a local tech tried a shop vac on the old drain. Didn't work. then I ordered a fitting that allows you to blow compressed air into the tank. No good, sent it back. This will save me $$$ when it's time to replace my tank.
Thank you great information.
Awesome video dude thank you very much! I now sound way smarter than I am.
@drewfortwenty5519
3 жыл бұрын
Remove the aerators on the faucet they're slowing the drain process from the filters
Nice job! thank you
Thank you, this helped.
Thanks very useful tips and ticks
@quickwaterheaterfiltration5292
3 жыл бұрын
You're welcome 😊
Super helpful!
Thank you for helping diagnose my first water heater replacement drainage problems!
@quickwaterheaterfiltration5292
Ай бұрын
Our pleasure!
Thanks for your video. Very helpful info. I have plastic valve and cannot get water heater to drain. I am sure sediment is built up inside. Water heater is 30 gal GE about 6-7 yrs old never previously drained. While I could probably change the valve, don't think I want to tackle it alone. If I call plumber, I will replace the heater.
@quickwaterheaterfiltration5292
4 жыл бұрын
Susan Thomson Yes. I agree. Probably better to leave it alone. Next time buy a water heater from a plumber who can install a 3/4” ball valve for you to drain your water heater.
Best video I have seen on this. Thanks!!!
@quickwaterheaterfiltration5292
Ай бұрын
Wow, thanks!
Good video that helped me. I have a Rheem unit and that dreaded plastic drain valve. Fortunately I was able to wrench it off and install the Ball drain as you recommended. The Plastic drain valve I had was defective because once I replaced it, draining was normal. Inspecting it showed what looks like a black o-ring inside and I suspect that is foreign and may have been a problem from the start since this is the first time I did maintenance on it. I also replaced the anode rod which was completely disintegrated. Nothing but the screw came up. Again thanks for the info. I saved $1,000 from adding life to the one I have!!!!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it was helpful!
Very helpful!
Thank you sir for your video. It really helped me to flush my water heater.
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it helped
Great video. I found that a short 3/4" close nipple for the garden hose side will not extend as far out from the water heater as a 2" nipple would and it works just as well.
Exactly what I was looking for!! Watched I don't know how many videos now and they all say to turn the gas to pilot or off, turn off the cold water or if none exist turn off the whole water supply. Then turn on a faucet with hot until the water stops coming out. Did all of that and still the only way water would drain out is if I turned the water supply or cold back on. Air locked!! Makes since but I never would have figured it out without your help. Thanks so much!!!
@emach07
6 ай бұрын
Oh, btw, when you mentioned the hot water faucet didn't do the trick because it was lower than the hot water heater (which is true) I decided before trying to loosen the hot water hose going upstairs and turning on all the hot water faucets 😁 Did the trick! Thanks again 🙂
Hey thanks for taking the time to make this video. You were very thorough and helped me with my issue. If I lived in your area I would use your service. God bless you
Thank you so much I learned alot
4:12 that lever is the pressure relief valve. All you had to do was open it. I just did mine and I was not understanding why it wouldn't drain but you helped me understand why. Thanks.
I plan to try this tomorrow, thanks for the video.
@quickwaterheaterfiltration5292
3 жыл бұрын
Good luck!
@theprophetez1357
3 жыл бұрын
@@quickwaterheaterfiltration5292 It was so bad he now wants to replace it.
Well done video
@quickwaterheaterfiltration5292
4 жыл бұрын
Nico Z thank you Nico
This really works. If you are unsure of he fittings talk to someone at HD or wherever you get your supplies to help. This is especially true for that little bit that connects the valve to the hose, it's kinda hard to find. My old plug would only drain at about a half gallon an hour. With the 3/8" straight shot, the whole thing emptied in about an hour! The old drain plug's hole pinched down to less than 1/8th inch and was totally clogged. Can't imagine this one will ever clog, but if it does, It will be a snap to ream out since there is no bend. You should have a large crescent wrench and a pipe wrench to make this. Don't forget the Teflon tape! The brass parts aren't cheap (ran me about $35.00) but worth it. This is a great hack!
Really helpful, thank you so much. One thing I will mention is that if you just need to do this one time to drain an old water heater all you really need is the 3/4" 2" inch brass nipple. The whole ball valve setup really isn't necessary for one time or occasional use.
Thanks for the tip. My 12 year old water heater was plugged right as a tick. Following your instructions, changed to a 3/4 ball valve and it drained perfectly. Changed elements and thermostats and flushed till clean!!
Thank you so much!
Airlock was my problem.. thank you Soo much!
very helpful thanks
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad it helped
Thanks for the info.
@quickwaterheaterfiltration5292
3 жыл бұрын
You bet!
thank you that worked!
The faucet below the water heater was my issue. Thank you!
Great video. Ball valve is a great idea. I’ve had one for years with no issues. I wouldn’t turn off the gas completely just turn it on the pilot. Why would you want to complicate relighting it and all that when all you need to do is put it on pilot? You can leave it on pilot with 2 cups of water in the bottom and it wouldn’t hurt anything and makes it much easier. Also instead of disconnecting the water supply lines to get air into the tank just use the over press test valve lever. Much easier to allow air into the tank. Thanks for posting
@quickwaterheaterfiltration5292
3 жыл бұрын
Thank you
@nude_cat_ellie7417
2 жыл бұрын
Unless you can’t flip the valve. I don’t know if it’s too old or I’m weak but I can’t flip it.
@condor5635
2 жыл бұрын
@@nude_cat_ellie7417 If you’re talking about the over pressurization safety valve then you probably need a new one if it can’t be opened with a flip!
@danielcardinale4562
Жыл бұрын
Seriously! That t & p valve is there for one purpose and if it fails to activate "KABOOM"
@condor5635
Жыл бұрын
@@danielcardinale4562 it’s not going to fail. It’s not like it’s a one time use. In fact they recommend testing it. Never had issues
That worked thanks bro!
@quickwaterheaterfiltration5292
2 жыл бұрын
Glad I could help
Always pays to go to the one who knows! Brilliant! You saved me so much headache! Thank you!
@quickwaterheaterfiltration5292
3 жыл бұрын
Glad we could help!
After watching several other videos this video was exactly what I was looking for. Thank you for clear, concise and useful information, my water lock was not as locked as I had hoped for but regardless of the small flooding the operation was a success!!
@quickwaterheaterfiltration5292
Жыл бұрын
You're very welcome!
You nail it , there was no air letting in remove the hose problem solve thank you
@quickwaterheaterfiltration5292
2 жыл бұрын
Glad I was able to help you
Awesome thank you!!
@quickwaterheaterfiltration5292
3 жыл бұрын
You're welcome!
Had to use a different method today on a hot water heater with a plastic drain that wouldn’t drain at all to much settlement inside had to use the gallo gun on it it did the trick!!
Thank you sir
Thank you!
@quickwaterheaterfiltration5292
3 жыл бұрын
You're welcome!
Ha ha thanks. Saved me some trouble. New subscriber. 👍
@quickwaterheaterfiltration5292
5 ай бұрын
Thanks for the sub!
Great content... Just wondering it would be the same for a lift pressure release valve. Would you have to open it up completely or just enough to get the water to flow? Thanks🎉🎉🎉
It work thank you