I'd like to compliment you on a job well done and I'll leave the last word to my good lady: "I'd be more than happy to have that jewel of an engine take pride of place in our living room".

That's not an engine. It's a work of art!

@dodgeplow

5 жыл бұрын

size. Straight sixes are longer than an inline 4 or a V8

@GreXOG

5 жыл бұрын

@@dodgeplow vw vr6 will solve it

@dodgeplow

5 жыл бұрын

Yes, but the question was about straight sixes, not V-6

@joeblow5244

5 жыл бұрын

It's all about cost now-days. More steel / weight etc. but the best for torque, as in Cummins diesel!

@mohabatkhanmalak1161

5 жыл бұрын

Glorifying the humble potato, are we??

Can't help but know you r from Canada. The aye 's give you away. All the best from our slides from the north. Loved Ontario lovely province! My direct neighbor to my East, across the big Lake! Keep the videos coming!

Fifty one years ago ,, as a seventeen year old, I had the experience of working on an XK 140 engine. I didn't know much at the time but I learned fast. It was very similar to the E type but not as evolved. The timing chains and tensioners had worn through the cover ! It was a mess. Your project has brought back fond memories.

@amirxj4077

5 жыл бұрын

Hello sir. What are differences between Etype engine and Xj series 2 engine? E type makes 255 --300 HP but Xj series 2 with similar 4.2 liter engine makes(Max) 155 --165 HP. I wanna buy an E type engine and use it to my dad's XJ 4.2 series ll 1977

@thebigpicture2032

4 жыл бұрын

I’m guessing those domed pistons are raising compression and notice the grind of the cam, probably much more aggressive than the XJ. Then add triple carbs and perhaps better flowing heads and exhaust, no pollution controls and you’ve added at least 100 hp

@markscully2342

3 жыл бұрын

@@amirxj4077 chances are that the engines are mechanically very similar most of the difference will be in the carburation and exhaust! I don't know about us spec cars but the series 2 xj 4.2 was rated at 202 or there about!

Just finished watching this episode. And I made up mind to say it was now a work of art. Then I saw Trebor's comment. But it's true. You are really making me miss my old car. Thanks for all of the great videos.

I was so enjoying watching you rebuilding this amazing and Beautiful E Type engine that I have watched every instalment one after another.it was great way to spend an afternoon...thank you

@RichardMichaelOwen

5 жыл бұрын

Great to have you along will have this running soon.

@Adibarum

5 жыл бұрын

@@RichardMichaelOwen Thanks Michael..I look forward to the future instalments

The torque setting for the valve cover nuts is 8 ft/lbs not 15. Brings back so many memories of rebuilding my engine a year ago. Great videos, thank you for uploading. (You may remember me / car parked next to you at 2018 Van Dusen white RHD FHC).

@RichardMichaelOwen

5 жыл бұрын

Stephen great to hear from you. Thanks for the torque setting. That white European spec S2 was a rare sight.

This video is great. I'm 71 and did my 150 engine 48 years ago by reading the book. Wish I had this video then. Got most of it right...still have the car, and amazingly, the motor still runs great. Thanks so much.

And nowadays engines are hidden under plastic covers. Give me the classics any day!

@dessullivan1725

4 жыл бұрын

Absolutely, this is pure engineering and all very comprehensible. How I'd love to work on one of these babies!

Beautiful engine! Nice to be working with your father on cars! Mine to was a crack mechanic. Yours at least shows you how to do things. Mine would never ever let see you d it anything except observe a master, hand him tools, go fetch tools, or run for parts. You r so lucky!

Pretty! Nice work. Hope you got the correct assembly lube smeared around for the initial start up. Now we wait for some carbs, lube and fuel to hear the BROOM. :-)

@ronniedoorzon1576

5 жыл бұрын

just start the enige with the sparkplugs removed, so that the oilpump can pump oil through the system. After that it's okay to start and run the engine.

Young man you are doing a fantastic job, my congratulations, just a tip from an old man, on those copper washers, if you can't find them new often you can heat them up with the touch, the copper often come back to his original shape, nice going , please keep us posted, I want to see more of it until see it running, from endless summer paradise Puerto Rico Jesús Torres.

Do yourself a favor and replace the $5 oil pressure relief spring. These springs lose temper from heat and age and will prevent the newly rebuilt engine from establishing the correct oil pressure. I bought a restored coupe that had low oil pressure even though the engine was a fresh rebuild. When I examined the relief spring it was so week I could compress it completely between my fingers!

@RichardMichaelOwen

5 жыл бұрын

Great tip, I did make sure the cup and spring were moving correctly before install.

This accuracy in work inspires self-happiness. Cheers guys

This is why men sometimes write songs about their cars or engines etc! Great stuff!!!

Loving the quality of workmanship you're putting in. And the lathe work is fantastic and worrying - I haven't used one since High School! I can see where it could easily go wrong, nice warning.

Brilliant.. thoroughly enjoy the whole series. Well Done.

Magnificent, a real pleasure to watch a real engine come together. I like the old stuff, all the best.

Hi, to follow up on Ove's comment from Norway regarding the oil return hose at 15:36. Since Jag designed this with different size ODs, I believe the way you installed the hose, extra clamps & sealant will fail in time. On my '68 E Type I've done the following. At the oil sump tube put a I" hose on it that fits that tube correctly. Then the hose from the filter head goes over that 1" piece to correctly fill the larger ID of the hose from the oil filter. Now when you tighten the clamps there will be no bulge as shown in your assembly. Great looking cam covers. You're doing a great job, thanks

@RichardMichaelOwen

5 жыл бұрын

That's totally possible to fail I agree. When will someone make the right hose?

@erniew5805

5 жыл бұрын

that sounds like it would be a better fit. i guess i should look back to see how it works. i see it called a return but sending filtered oil back to the pan doesn't see right. so i assume there is pressure on that line.

@2541968joey

5 жыл бұрын

@@erniew5805 This is a by pass hose if and when the filter clogs up this hose would then return oil to the sump but under most conditions my thoughts are very little oil flows through this line. My tip of using two different sizes of hoses is to get a better sealing onto the smaller OD sump tube. The best solution would be to weld onto the sump a tube the same OD as the filter head tube.

@erniew5805

5 жыл бұрын

@@2541968joey ok thanks for clearing that up for me. using the 480 psi hose is overkill then . using oil resistant hose of a lower psi rating might be easier to seal off as it wouldn't be as stiff. but replacing the tube would be the gold standard .

@ovenorway

5 жыл бұрын

Richard Michael Owen Any supplier of Jaguar parts should have the correct part in stock.

Excellent work. I really enjoy watching you work and the attention to detail. Cant wait for the next episode.

Totally enjoying following your rebuild. I was in 'workshops' from a young age here in Cambridge, England (late 60's) and I recall blue hylomar was for water related parts, and we also had red hylomar for oil related parts to seal. I've never known it as anything else. We also cut our own gaskets for pretty much everything.

@RichardMichaelOwen

5 жыл бұрын

Very cool, thanks for watching. Was that possibly Hylotyte Red?

Another piece of fine "simple" English engineering!

Wow I’m loving the detail, that gold together with the polished ally rocker covers beautiful. 👌👌👌

Ive only rebuilt mainly American engines, but its been very enjoyable learning the particulars of these grand old engines and watching this work of art go back together. Im well aware these engines take more care and knowledge in certain areas due to their complex and not always perfectly engineered nature, but when one is up and running in proper condition they look and sound oh so beautiful. I love my muscle car V-8's but these engines are a different animal - they have a look and sound thats so much fun to run the gears on, sadly ive only seen videos and only drove one once myself so feel ive really missed out.

Un superbe travail !!J·admire votre savoir faire ...Congrats ...

Thinking back 40 years, I remember polishing the cam covers on my old 3.8 S-type - the oil housing hose may have leaked like hell - but the cam covers and SU carbs always looked great!

I watched the entire series. Wonderful way to spend a relaxing day. Thanks for sharing.

Blue Hylomar well known in UK. Odd stuff to torque down maybe? Love your engine. Watch those fingers on the lathe! How many times would I have been ****** without the old man?

@RichardMichaelOwen

5 жыл бұрын

Malcom, thanks for watching, great to have you along. Oh man I would hate to do this on my own, sometimes I just fail at things. It weighs hard when something goes wrong for quite some time.

Great video series and you do a great job producing them. Excellent work on the engine. I wasn't sure about the gold color at first, but after seeing it together, it's a piece of art. Thank you for sharing.

Thank you Richard ! You have inspired me with your videos. "EXCELLENT " I have two 69 e-types that are in need of total restoration.

That engine is a work of art! I’d love to have it on display in my living Room!🙀👍🏻👍🏻👍🏻

Great series of videos, shared with my pal who owns an E-Type and a Mk II. Look forward to hearing it running

Richard, I spray the gaskets days before with the high tac red spray a gasket. Mopar makes one, Gasket Sealant. Then 20 mins before assembly, spray lightly, let tack-up. Also, for badly pitted surfaces. Spray the metal, (mask off) let dry. I never have leaks on the XJS.

Yeah , when i was a kid i worked in a machine shop and the foreman told me be careful on the lathe. It said "that thing will kill you as fast as anything". That thing is beautiful and so very british!!!

A marrvellous result - well done ' A thing of beauty is a joy forever '- would love this mounted on a mahogany plinth just to look at it !.

Great job richard. love the copper washers and domed nuts awsome job..

Great to watch this great engine being built up. I CAN wait for the start up, because I do enjoy the step by step build. Thanks Richard.

@RichardMichaelOwen

5 жыл бұрын

Great to have you along Reg, thanks for watching.

Looking really nice. Black and alloy with a touch of copper, lovely.

Poetry in Motion! Can't wait to hear that roar! Thanks again for this great rebuild Junk E engine NO MO!

@RichardMichaelOwen

5 жыл бұрын

Might run like junk let's see. There is a slim chance I need to get the internals balanced.

That is a real beautiful workmanship. You can be proud of it. Have fun driving the Jaguar, it's a classic. Best regards from Hans from Upper Austria. 🇦🇹

Greetings From The UK - Excellent Job - and well delivered to camera and verbally

Looking forward to the wiring going on - fantastic job so far.

Richard on the hose clamps, to really make them work effectively and seal, you need to put the hose clamp right up to the bulge in the hose created by the raised lip on the end of the nipple. Don't clamp on the raised portion but right behind it. That way it's pulling the hose down around the raised lip before going under the hose clamp. I hope that's understandable it's one of those things that can be hard to explain in writing but I could show you in 2 seconds. Good job so far I can't wait to hear it run.

@RichardMichaelOwen

5 жыл бұрын

Thanks for the comment I totally agree. Also try to look for pipes with raised lips, lots of the hardware from SNG Barratt has raised lips.

I am proud to say I actually owned a 4.2 2+2 and like an idiot sold it, the one vehicle I owned in my lifetime and should never have sold. Owned it before any speed restrictions were brought in, in the UK so it was always a blast to run down the Motorway to blow the cobwebs off so to speak. Happy days. And just remembered I still have the original Tyre Pressure Guage inscribed Jaguar as supplied when the car was originally sold new.

@rondyechannel1399

5 жыл бұрын

Yes, I restored my Series II then sold it before they became the Holy Grail. I couldn't bear to pay the price to replace it now.

I think I would have plugged the spark plug holes during assembly. For a "junk" engine you sure are meticulous. Very nice!

That’s got to be the nicest “junk engine” I’ve ever seen it really is a thing of beauty. 👍

@mohabatkhanmalak1161

5 жыл бұрын

You too, glorifying the humble potato. Wake up men of nuts n bolts! While Jaguar was using "dome nuts" on these engines, Mazda was already working on improving the Rotary Wankel engines you could fit into a suitcase!.

@derekwilkinson7939

5 жыл бұрын

Mohabat khan Malak. Tell me which one looks the best. The jag engine or Wankel engine?

@mohabatkhanmalak1161

5 жыл бұрын

@@derekwilkinson7939 Wankel for sure. And on looks, would you want "looks" under the bonnet or in the sleek lines and shape of the car??

@derekwilkinson7939

5 жыл бұрын

Mohabat khan Malak. The E Type is one of the most beautiful cars ever made. With a beautiful engine. In my opinion.

@mohabatkhanmalak1161

5 жыл бұрын

@@derekwilkinson7939 Mercedes Benz SL beats the E Type hands down in comfort, style and build quality. This is before the Datsun 240Z (Nissan Fairlady)comes round the corner!! The SL, mind you had the Bosch fuel injection, a novelty in the 50's and 60's.

Thanks for posting detailed and high quality video, I am finding it very informative and useful as I am in the middle of rebuilding the engine from my '74 XJ6 4.2, my block should come back from the machine shop next week with +.020" overbore and then I can get busy reassembling. Not going to be a patch on yours mind, for a 'junk' engine yours is looking better than new now! Looking forward to seeing this start up.

@RichardMichaelOwen

5 жыл бұрын

Thanks for watching, if I was doing it again I'd probably replace more, so the rod bolts, distance piece and oil pump.

Use a black "sharpie" pen to fill in the "Jaguar" markings on the oil cap. You will like the results. Additionally begin your initial cranking over with the coil disconnected and look for oil pressure on the gauge to insure you have full lubrication. It also would not hurt to inject a squirt of Marvel Mystery Oil into each spark plug hole and crank over with them only finger tight at first.

She's stunning can't wait to see it running!

Very nice!! Great attention to detail.

I totally agree, I’d have that work of art in my living room. You’re Dad is the Google of everything!

I was introduced to Rolls Royce joint compound in the mid 60s when I was overhauling J-34 & J-47 jet engines. It is a wonder sealent.

@RichardMichaelOwen

5 жыл бұрын

Do you know how much pressure it can handle? Can coolant pressure move the Hylomar?

@alandowney5851

3 жыл бұрын

@@RichardMichaelOwen Bit late to the party... I've used Hylomar on aircraft engines, car engines, and bike engines. The amount of pressure it can handle is really down to where you use it. But suffice to say, if you have two nice flat surfaces it is a very effective sealant and I have used it successfully even without any gaskets on timing covers and similar in the past without issue. I wouldn't be crazy about using it in very hot or pressurized areas but it should be fine in the coolant system. I was wincing looking at you polishing the cap on the lathe - please use a stick or something in future and don't let your hands anywhere near a spinning chuck!

Wonderful job. Top of the day Sir....

Could not help but notice the TR6 in the background. Hope it gets as much love and attention .

Beautiful. They’re a nice looking engine.

Great work mate these can be such a pretty motor done up. Always love the gold accents. I have a 420g with about 3 motors collecting dust in the corner of my shop, this is inspiring me to do them justice and get stuck in. Keep up the fantastic work!

@malcolmr800

5 жыл бұрын

I have 420G bought as a parts car but too good to scrap. Available either complete or parts Call/text me on +1 778 nine eight seven five 858

Great job, enjoyed this episode

very pretty looking engine!

With all the complex parts, assembly and torquing, we now know why Jaguar overhaul is so very expensive. This series should be used for every mechanic school.

@thomascatford2627

5 жыл бұрын

Jaguar or JCB its still just an engine

@markgallagher0000

5 жыл бұрын

i think not,the story here is get daddy

That is a beautiful engine!

That looks like a different engine than what I commented on the other day - I’m not seeing the “hook” the right cam sprocket sits in... Well done!!!!

blue hylomar sealant was developed by Rolls Royce post WW2 to seal things up in the early days of the jet engine development. It's years ahead of silicon sealants and does not set. (will dissolve in your engine) not destroy it!

@alexbrown1995

5 жыл бұрын

I've used the spray can Hylomar for years but had no idea there was a tube version. Now on my list. Thanks, Richard. Love your work, mate

@peterjones6945

5 жыл бұрын

It used to say on the tube it was licensed from Rolls Royce (in 1970's~80's) No idea if there is anything there today? I didn't know it was post WWII, always thought it was in Spitfire engines and was non hardening so it could go through oil pump or any oil passage without damaging anything. Wasn't aware it would dissolve in engine oil

Wonderful job, cant wait for the next upload

Funny with the title of the vid. Clearly not a junk engine. Nice job!

I use my lathe to file, sand and polish everything round. Made a polishing head for the Bridgeport. Once, I slightly hit my knuckle on the jaw, that was smarts. I use paint mixing sticks from HomeDepot. Large and small. Hold sandpaper on stick against part. Your speed is a little fast, about half. My 2 pennies.

3:02 Love the Gold in the plug valley... NICE!

@rossilake218

3 жыл бұрын

Love that gold color! Looks beautiful, only a British car lover would say that. Cheers! from Chicago.

Great job Richard.

The bracket is part of the tensioner. it should have a pulley attached to it that acts like an automatic tensioner for the belt that goes around the harmonic balancer pulley and the water pump pulley. hope this helps. Great series!

Just so you know, I am not being pedantic or some "knowit-all." Somewhere in at least one of these series I saw you mention a thing, a rather important thing. You took down an engine and said (I'm paraphrasing) "This cylinder has a ridge so we'll bore it out .020 over (or whatever dimension you said)." Small thing to note here, a ridge does not automatically mean bore it out. A ridge can be simple buildup and many times boring out a cylinder is not the answer to "fix the ridge." I am not certain if you corrected this already so ignore me if you did. I am enjoying the series so far, even if this is "older content now," I just found your channel.

I would venture a guess that your beautiful engine will not leak a drop. It is almost to pretty to let run and get dirty. Great job, so far.

I recall getting a lift in a jag as a spotty kid. My dad always had junk cars that ran like crap. The contrast with the jag was so extreme. The cool shiny leather seat, the dash was beautiful patterned walnut. I couldnt hear or feel the engine. When he took off i was squashed up into the seat with the acceleration. Like being in a gentlemans club and being shot out of a cannon at the same time. I rememember seeing lots of new jags lined up dockside for export over the atlantic to the usa from liverpool. Sorry to see them go.

Stunning Richard.

Great video.ive seen the jaguar infill on the oil cap done in red. looks a million dollars!!

Really looking good.... still not convinced with the gold though. Hey ... What the heck.... nice job,Very well done.... Can't wait to hear and see it running C. :-)

It should be under glass in the Garagemahal! A work of art.👍🏻

Great job close to perfection!

I have an XJ6 with one of these engines, if you’re ever down in New Zealand you could do something similar - I’ll supply the beer!

Can't wait to see it in and started. It's beautiful.

@RichardMichaelOwen

5 жыл бұрын

Hopefully soon, just went though the distributor today

@richardgerathy1223

5 жыл бұрын

Good luck. I'll get some of my mates to subscribe too. @@RichardMichaelOwen

Hi well seal is Brown & sticky, hylomar is blue sticky but different 😅 great videos thanks, just about to do the same to my 3.4 thanks John from the isle of wight GB

For the smaller size hose barb, braze a tight fitting tube on the barb, split it if you have to and use bailing wire to twist/ clamp it in the middle while brazing. Clean/Sand to smooth condition. When the hose is over it it you will not notice the work.

Thanks, good build.We call it hylomar in England.It states on the old tubes.Used by Rolls Royce. :)

It's called hylomar in the UK too, used it for years

@jamesgerard4505

3 жыл бұрын

Hey, thanks for the name, "hylomar". I was watching a different rebuild video where the engine was being assembled without gaskets. As I recall, hylomar was used in Rolls engines that were machined so carefully that gaskets were not needed or wanted, but to avoid any unsightly seepage, hylomar was sparingly used. I described the material, but couldn't remember the name, and didn't take the time to look in my "glue" box to find the tube. I only remembered the blue color, er colour.

Third watch. Beautiful engine, beautiful job.👍🏻👍🏻

@RichardMichaelOwen

3 жыл бұрын

Thanks Robert, great to have you along

Nice job look forward to watching your videos . I have restored a few Jags in the past . I did a semi restoration of an E type back in the 90's for the bodyshop I was working at , the guy was a tight arse and woudn't spend the money for new parts so had to make half the panels , had to make the rear half or the bonnet sides as I didn't want to see patches when you opened the bonnet , had to patch all around the panels I was given I was a nightmare .

@RichardMichaelOwen

5 жыл бұрын

John, wow yeah I hear the aftermarket fenders are no good anyway. bodywork on an E-Type is real trouble.

New subscriber to your channel and i like it very much...

Hello Richard, just found your youtube site, amazing work not to mention the time it takes to also film what you are doing!!! I have always loved the XK140 AND especially the XK150 OTS. From what I gather, even though you buy what is supposed to be a great looking XK, you really never know what is underneath or the reliability of the drive train...all labor intensive and expensive with loads of surprises. Would it be fair to say that when you are looking at buying, it is best to have someone like yourself fly over for an inspection and/or just look at booking the car in with you for a complete restoration? All my best to you and your father. Michael

If you had welded the oil holes in the cams, they would definitely take points off at Monterey 😀😀😀. Also, when fussing with those bolts on the front of the cams, I would have stuffed a rag below to catch anything that dropped. I notice that, as was custom of the time, the breather vents to atmosphere.😰

@RichardMichaelOwen

5 жыл бұрын

The breather housing actually goes over to the intake, I guess the other option would be fitting a catchcan.

Nice work. Blue hylomar used to be made in naylor st in liverpool !

Great series, very usefyull

Hylomar (blue)was developed by Rolls Royce , weld-seal (brown) is a different product in the U.K. believe me I have used many tubes of these sealants . Lock wire should be in a “S” shape pulling the bolt clockwise , On the cam timing gear, the toothed camshaft adjuster is called a ‘’Vernier adjuster” , on the two bolts that hold the assembly together , one is a dowel bolt,and should be screwed in by fingers only to ensure it is aligned correctly . I went to Jaguar and did the 4.2 engine course in the mid 70’s. Hope that helps

Blue hylomar is also sold here in the uk, as approved by Rolls Royce none the less!

Classy work!

To find TDC using a dial indicator, the best method is to use a degree wheel and measure the degrees away from TDC on both sides of it: First find a preliminary TDC and go to .050" or .100" piston drop on either side, mark the two on the degree wheel and then 'split the difference' on the wheel. THAT's the true TDC. This is another reason to use petroleum jelly on your bearing inserts. Using oil can allow as much as .001" play in the bearing, throwing off the dial indicator reading. If you did use oil, measure both of your 'drop marks' on the approach to TDC. For best accuracy, use PJ on assembly and the "split" method to find TDC accurate to the minute. None of this takes extra time or effort, just a different method that is more accurate. Petroleum jelly also keeps a greasy separation of the bearings from the journals until the engine can develop oil pressure on the first start up. Some guys will run the oil pump with a drill on engines with an OP drive shaft, like some older American V8's, but if you use PJ on assembly you don't have to.

@RichardMichaelOwen

5 жыл бұрын

Yes that is a much more accurate system, totally agree.

@ladamyre1

5 жыл бұрын

It's a pleasure watching you work on this engine Richard. Your attention to detail is reassuring that there is somebody else in this world who loves to do a good job and have it look the best he can. I would have had those aluminum covers polished to a mirror shine and clear coated, but the finish you have is still fine. And I mean "fine" as in excellent. A matter of taste I suppose. You are doing the first thing any good technician does: *go to the service manual.* Nobody knows better than the guys who designed the engine.

Bravo, Mechanical Poetry!

Jaguar used a special hose between the oil filter housing and the sump. If you measure you will find out that the outlet pipe on the oil filter housing and the sump inlet pipe are two different dimensions. If you use a regular hose with the same diameter on both ends, it will leak.

The spacer you mentioned that is for the bracket that hol the dyno. I had the same problem that it scratched the water pump housing ( but i had a aftermarked waterpump from SNG barrat- nothing from there fits) but I did have the same spacer that i had marked 3 year ago when I took it apart. I have a picture and it shows that the spacer are just slightly wider that the bracket it selv. But we have 2 different brackets...

Lovely engine. Nice rebuild. I saw a comment on another rebuild video where the mechanic was not wearing gloves. The commenter said that bare handed work was "old style". I guess I am an "old style" mechanic. I started rebuilding engines in 1953. I wouldn't wear gloves like those if you paid me. I love the feel of the parts. It is like I can "taste" the metal with my fingers. I deliberately (is there another word?) fondle the engine and all of its parts. It isn't like I do things brutally and have damaged hands. It is more like a violinist coaxing notes from his instrument. You might want to try feeling the parts bare-handed. It might add a nice dimension to your enjoyment of your work. It is tempting to say you would do better work, but I don't think that is it, although I think you are missing many tiny details. You might find yourself smoothing edges more carefully, just so they feel better. I find it impossible to imagine where, how, and why you became convinced that wearing those airtight sweat retaining gloves was a good idea. Maybe my question is "what are you afraid of?" It is a matter of a deeper pleasure and connection to the soul of the machine. I wear gloves if there are toxic or corrosive chemicals involved, but as soon as that is done, the gloves come off. My hands want to be in the air, in the most direct contact possible, feeling the textures and temperatures and the finish. It is truly a sensual pleasure. Anyway, you are building a beautiful engine, and I will look up the older videos, and look forward to the next ones. Thanks for sharing. PS, just found episode 1, and you were removing the valve covers bare handed. Aha, maybe there is hope for you after all.

wow it is like a saxophone :) i d like to hear it roaring

Brilliant. Now when do we see you do a similar job on the 'My junk E-Type Car' that it turns out you just happen to have lying around?

Looks amazing