Six beginner/low budget end mills for aluminium(Affiliate links): Test video with Feeds and Speeds: kzread.info/dash/bejne/f2FlxruDh8uZoto.html Tool 1: ⅛ inch 2 flute: bit.ly/2N2DyEE Tool 2: 4 mm 3 flute: bit.ly/2N2DPXZ Tool 3: 5 mm 3 flute: bit.ly/2N2DPXZ Tool 4: 4 mm 2 flute: bit.ly/2N1KYb2 Tool 5: 4 mm 2 flute: bit.ly/2SxnT6g Tool 6: 6 mm 2 flute chamfer: bit.ly/2tmihfX

@ryankraft9897

5 жыл бұрын

I wouldnt recommend AlTiN for aluminum. Stick to ZRN. The alumimum in the coating will bond with the aluminum piece

@jamestiberious1372

5 жыл бұрын

The speed and feed your using is creating alot of backlash. Also if your getting vibration, reduce your spindle speed rpm not feed rate. I'll send a formula for working out speed and feeds. Some great speed and feeds for Ali Spot drilling S-3000 F-150 Normally go -2mm from Z0 Normal drilling S-3000 F-300 Peck 2mm ( will clear all swarf) Tapping Ali only - S300 for feed rate X by pitch. Example 12x1.75 S-300 F-525. To get really nice finishes your gonna want to do ruff and finish passes. The reason you had and ok finish is you was tracoydal cutting. Which will required a slower spindle speed but faster feed rates and small step over. If you was to do the ( ruffing ) in 0.5mm step down then a finishing pass at full depth. You should also get a nicer finish. Sorry to go on but hope this helps. And questions feel free to PM me Btw I work on Hurco VTXU 5axis CNC

@muntee33

4 жыл бұрын

James Tiberious Trawlin through YT looking for beginners advice and tips for a good 1st mill, starting to ‘get a feel’ for what direction to head in, then you bust out with whatever language that was, and the reality of the learning curve ahead of me to even begin to understand what the hell that hand controller contraption does kinda dawns on me... Sounded like when I hear welders talking or something....

@jamestiberious1372

4 жыл бұрын

@@muntee33 first mill in what regards? Machine or cutter? It also depends on what type of material you want to cut with it. If you let me know il do my best to help with what I can

@chrome4096

4 жыл бұрын

even if your just beginner...or maybe especially whe... get a amachinist handbook and learn the 3 simple facts about feed, rpm, and the most important cutting speed. It all comes down to this, and the sure have a bit leewayy but not really that much if you dont have expirience. For example: handbook will say: aluminium needs cutting speed of 350 m/min and maybe 0.05mm advance per tooth of the endmill tool diamitar is lets say 8mm you will end up with 14 000 rpm and a feedrate of 2100 mm/s thats a bit crazy so if you want to tone it down then adjust feedrate and rpm at the same values so you maintain the depth of cut...afterall cutting aluminium is basically(...) the same, so tone it doen according to the machine and it will be fine

I am a certified precision machinist, you should always use 2 flutes mills on aluminum, and if you want a better surface finish increase the rotation speed to the maximum the machine will run and then slow down the movement speed, and the depth of cut and bite you take out of the material. On the large CNC machines we will take a .030-.050 depth pass. This also depends on the length of the mill the longer the mill the more deflection you get which results in chatter and a rougher cut. But on my final pass I will drop that depth to around .015 and get it super smooth. Keep in mind which way your machine flexes in the Y axis, try to control the path your mill is traveling so it cuts going in the more solid path of X axis, and uses Y axis for it travel rather than cut. So on your final pass decrease the depth to .015 and instead of the mill cutting the length way of the machine, have it travel back and forth across the machine as you mill and keep the pressure the mill is receiving against the more solid axis. You might find that improves the finish surface as well, if not fab up some supports for your Y axis so it is not able to flex like it does. Great video, I am trying to decide if I would be happy with one of these machines at home or if I would just be driven nuts by every little imperfection compared to a full sized CNC machine and how they output.

@eastcoastguitar222

2 жыл бұрын

Did you end up buying a CNC for home use?

@brianfoster7064

Жыл бұрын

@florian florian As I understand from my research (looking into getting one of these) three flutes are best "middle of the road" bits - they can do it all but not as well as bits specific to the job. Single and double flutes are best for roughing. Four and five flutes are best for finishing.

I would like to comment about why this Endmill, not called a "BIT" broke, it is Not because it is a cheap High Speed Endmill, it is because it is a 4 Flute endmill designed for steel. When we cut aluminum we use a single, 2 or 3 Flute Endmill because they do not get loaded up with aluminum when the endmill gets Hot and makes the aluminum gummy especially when cutting 2024 or 01 condition aluminum. If you would slow down the speed and feed according to your cooling of your endmill and use less flutes it is possible to use High Speed tools. Infact during the 80's it was unheard of to use carbide to cut aluminum because up until then they, (the Carbide Endmills) were not ground correctly to cut aluminum. The manufactures started using different designs and geometry when grinding the carbide to bring about the designs we now use today. I have been a CNC Programmer, CNC Operator, tool and Die, and Mold maker of investment casting molds and Plastic injection molds for the last 40 years and have seen this industry grow throughout the years. Now I that I am about to retire I will have a 4 foot X 4 foot Mill of my design and build in my garage to have many years of FUN with! Enjoy!!

@JohnHoranzy

2 жыл бұрын

Nobody ever uses the Machinery Handbook or ever does the math and they just copy everyone else with bad information.

From my experience in aerospace I learned a valuable rule. When you pay for a a drill or cutting bit, you are paying for the quantity of accurate holes or cutting they will preform. A $1 bit that makes 10 decent holes costs more per hole than a $5 bit that makes 100.

@PiefacePete46

5 жыл бұрын

Add to that the disappointment and frustration of poorly finished or ruined parts, and some people will become disheartened and take up knitting instead! Your early attempts may still be part of an actual project that was the reason for buying the machine in the first place. My experience is that the immense pleasure I got from proudly showing off my beautifully crafted veeblesprocket is what made me want to try the next step. Buy the best tools and cutters that you can!

@pierregauthier3077

4 жыл бұрын

If you can't run the speeds and feeds the tool was designed for or if you lack rigidity your tool will fail no matter how much you pay for it

6061 is typically the easiest to machine. As you discovered, 2-3 flutes are all you want for aluminum to allow for chip evacuation and prevent welding. With the lack of rigidity of your machine, light radial cuts - especially along the x-axis - will typically cause vibrations that ruin the surface finish. You have to either finish with higher WOC and less DOC, adjusting for the flex of the machine or change to a conventional instead of climb cut so that the flex occurs parallel to the wall cut instead of 90 deg to it. Climb cutting is great if the machine is rigid enough.

Nice to see aluminum stock being experimented with more and more!

Thanks for sharing your experience

Awesome! If you ever consider upgrading the router just go straight for linear rails. With router spindle speeds a single flute endmill is almost a necessity, it allows you to take an actual chip at lower feedrates to better suit less rigid machines, and single flute endmills are extremely rigid and are harder to chip weld (not impossible ;). If you plan on cutting plate, get stubby endmills, saves carbide (money), and makes your setup more rigid. If you're still having trouble, take a smaller axial cut. I hate doing it, it multiplies the program length but also drastically increases reliability. Don't be afraid to lower your spindle speed to cut a real chip. Idk what you're running in your mister but tap magic has some aluminum mixtures that I've used before and liked. Up the air pressure and make sure the chips are getting blown out, the air blast is more important that the mist, gotta get those chips out. I've worked with an omio x8-2200 which is essentially a 6040 with linear rails and a 3hp spindle. My friend and I have cut boat loads of alu for an FRC robot, and it works great. We can do full depth adaptive in 1/4" plate with a 20% WOC on a 5mm carbide single flute at 40+ ipm, and we slot often to cut out parts, but this requires a lot of feed rate override and micromanaging to not break bits. This is just me typing up a bunch of stuff, I'll likely comment again as I remember more things. Feel free to reach out if you have any questions.

@dougj56

6 жыл бұрын

Mo MO

@c.e.kestner4051

5 жыл бұрын

remember that WHATEVER you use as a coolant will be coating your lungs, too.

I learn a lot from John Saunders (nyccnc). He has a professional shop now, with big machines. But he started humble like you. And there are enough principles that apply to big and small machines alike.

Maybe a minor tip: don't use MDF or wood-fibre plate to clamp your workpiece on, specially when using liguids for cooling. It compresses when you clamp your workpiece on it, but worse: if you use water or water/oil mixture or any kind of liquid to cool, this liquid will be sucked in by the waste-board and this may distort the underground, which in turn could result in reduced clamping force of your clamps, your workpiece could get loose etc. And indeed, increasing the stiffness of your construction may increase quality of the cuts. Why aren't you using special cooling fluid in your mist-spray device, it's just designed for that purpose, it won't make such a mess as using water and a spray can of WD40. Nice video though.

Finally a video that shows what I have been looking for. A CNC router good enough too work on heard t6061 aluminum. So it should not be much harder to put a few designs on my anodized 7075 aluminum lowers

Awesome. You did your due diligence and tested the machines capabilities. 2 and 3 fl are best for aluminum. 4 will chip-weld. Mist is also best, so good job. Should spray a bunch of that wd40 in the bottle and save yourself the hassle.

@PiefacePete46

5 жыл бұрын

I am a great fan of single-flute cutters. They do a lot to improve chip evacuation, and reduce re-cutting. Also, more space for coolant and air to reach the cutting edge, and reduce melting of the aluminium.

Thanx for sharing,1st vid i have seen, with what i wanted to know about cutting Aluminium cheers

Hi there, One of the things I noticed was after the first outside cut was made and the machine moved to the next run that you have the feed the wrong way round which makes the bit try to climb over the sidewall and not cut correctly if the cutter is running clockwise than the feed should be anti-clockwise which draws the cutter into the cut and not cause it to try and climb out of it.

I experienced the same issues cutting some types of aluminum where the cutting wasn’t what I had hoped for. I have some that mills really well and other pieces that don’t. I found that mild steel always seems to cut well though.

What a great video man. Thank you.

In the industry we use Varsol and a misting bottle for aluminum to keep the carbide cutters from sticking to the chips. I even used it on magnesium bell housings for Ford Trucks.

Looks good . My 2 cents is Stop Climb Milling go to conventional milling. And WD-40 for aluminum makes big difference. And a nice piece of 1/2 " steel plate or even heavier will stiffen things up "less chatter and More Mass " Keep up the good work

Hi there, One thing that I don't think anyone has mentioned yet which is actually the source of ALL of your problems, the motor to leadscrew coupling. I'm pretty certain on these beige coloured machines, they use a flexible aluminium coupling between the stepper motors and the lead screw. Because it's flexible, any lateral cutting forces will cause the axis to bounce on the flexible coupling.

I've got the same machine. For Ali I use single flute carbide cutters. They leave a good surface finish. The bending of the x rails bothers me but as long as you don't push the machine too hard it doesn't affect things too much.

Kudos for testing your machine's capabilities and finding a "sweet spot" for what you want to run. You discovered the hard way that aluminum should be cut with carbide end mills that have at most 3-flutes, and that the alloy matters. 6061 is the easiest to machine, although your 6060 looked fine. Two notes: 1) A flexible machine will leave a worse finish when climb cutting. Try a conventional cutting strategy on machines like the 6040 and use climb cutting for rigid setups like true CNC mills. 2) Instead of using water and WD-40 separately, use a water-soluble coolant/lubricant like Kool Mist that is designed specifically for mist systems.

Nix the music. I'd rather hear the aluminum chips flying than the repetitive tune of the music. lol I was looking at the 6040. Good to see what it can do.

@birdman7135

4 жыл бұрын

I kinda liked that funky beat.

Excelente trabalho! Parabéns.

The play in the x axis can be somewhat mitigated my mounting you work closer to the gantry and not in the middle of the machine bed.

thanks for the video! i've been looking at one of these machines to acquire. maybe a used one. anything chucked into a spindle is called an endmill...not a bit.

good work

Really enjoyed that thanks, like that you kept all the learning points in too. What do you think messed up that final cut?

Welcome to the CNC brotherhood. From someone who has been there and done that I would pass on a couple of tips. 1) Starting out don't buy dear bits you are going to break heaps of them. Buy quantity not quality to start with (unless you have very deep pockets). It's false economy because when you don't know how to use them properly you are going to break or wear them out just as quick as cheap ones. 2) Learn about a climbing cut and a conventional cut, and you will very quickly work out what went wrong on the M. (mostly the machine is not really good enough at this point). 3) Learn to work within the limits of the machine and things like chatter will be greatly reduced. 4) Learn the appropriate cutter for the job, as you half worked out that alloy needs to be able to clear the cutter to stop the tip clogging up / welding. The problem was not the amount of flutes you had, but rather you weren't going fast enough for the amount you had. The machine currently can not go fast enough for 4 flutes so instead of speeding up, reduce the amount of flutes down to one or two, so you don't have to.

@MBcreates

6 жыл бұрын

Thanks for sharing your knowledge!

@keithlucas6260

5 жыл бұрын

I've taken busted two flute endmills and made single flute "flycutter" for high rpm finish cutting.

@lpjunction

5 жыл бұрын

@@keithlucas6260 For my ER-11 collet I put in a 6mm single flute straight edge usually used in wood work for trimming edges. Works for plastics and aluminum.

Try out some single flute endmills. It will allow you to use reasonable spindle speeds and feeds. I have this exact router BTW and have really enjoyed it so far. With a 4 flute you're not going to be taking a big enough bite with each revolution and the cutter will heat up fast. I've had great luck with aliexpress carbide single flutes especially the 6mm ones. For smaller, I've had good results with the ebay sourced kyocera single flutes. Good luck and keep it up with the vids!

@MBcreates

6 жыл бұрын

Thanks for you reply! Could you share some links from both end mills?

best to use a single O flute carbide from Amana for Aluminum. This will help a lot. $35-$50 each.

At that surface rate, you should be using a 1 or two flute Carbide Endmill with a 45 degree helix. Also, shorten that tool stick-out, unless it is needed.

nice video ,Thank for sharing

Remove the air pressure or severely lower it. For surface finish you need to slow down the movement speeds. Keep the spindle at the high speed though. Your rig is moving too fast at the end to get a good enough finish with that much surface area hitting the bit. Also if you do a deep cut finish like that in the future. Make sure the bit is as straight as possible. Maybe make it a two step process. Have one bit for cutting and another sharper one for finishes. That would save you time and money in the end.

i was a machinist 20 years ago, we would never use those tiny cutters for the bulk of the work, use a 12mm slot drill/ end mill for the bulk of the cutting, then use the tiny one just for finishing the small corner radiuses

@kayboku7281

3 жыл бұрын

nice job tho! Id say thats a success! Hmmm how to get rid of the chatter, id still say do a finishing cut of 0.5 mm at full depth with a larger diameter slot drill, larger diameter = less vibration, and try to only use the tiny slot drill to do those radiuses, might need a dremel of some sandpaper to help the blending in the finishing cut.

Another reason for breaking cutters can be vibration and cutter loads in corner and bends of cut. With a pocket with alot of turns of corners it can load the % of the tool higher and would need the feed speed reduced and some case increased. Chatter residents can break tools too and can be fixed by change feeds and speeds and placement of the part in the fixture or vise.

watching your other vids how you replaced the bed and aligned the head so its square to the bed, has that on its own improved the finish compared to that last final cut where it was flexing the machine? or just different speeds and feeds has fixed that? Im looking at getting a 6040 very soon ive been watching lots of different vids from people they seem to do what I want to do but just seem a bit flexy, like anything do you buy cheap then spend money to upgrade it to something better or buy something more expensive to start with.

Nice!

A couple things I noticed, and a couple suggestions - When using that small of an endmill, smaller chip loads are better, stepover is generally 1/3 the diameter, .050" depth of cut is decent. When clamping, make sure the fulcrum is always slightly higher than the work to be held. Your 'axial cut' aka finish cut really shouldn't be removing more than maybe .005".

@MBcreates

5 жыл бұрын

Thanks for the tips! could you explain this part further: "When clamping, make sure the fulcrum is always slightly higher than the work to be held."

@No1sonuk

5 жыл бұрын

​@@MBcreates With straight bar clamps, the work end of the clamp bar should be lower than the supported point. It makes sure that all the pressure from the clamp is downward onto the work and table. If the fulcrum (supported point) is lower, and the bar is coming up onto the work, there'll be sideways pressure on the work as well as downward. You might find this useful: www.homews.co.uk/page289.html

@rsilvers129

2 жыл бұрын

@@MBcreates He means the height of the far end of the clamp should be at or above the level of the part that is clamping.

I have a 3040 CNC, i don't have cut aluminium yet but i think it's more solid due to its less dimensions

Needs to run way slower feed, Needs roughing pass and finish pass FOR SURE! 4 flute-5 are for steel typically. 3-2 flute are best for Al.

Nice! Is there no more practical way of fixing the material to the cutting table?

use methylated spirit with a spray bottle. it allows for much more clean cut and less load up on the bit. you'll see the difference.

couple of tips: 1, turn WD40 can upside down and remove all pressure, drill a hole into bottom and fill that mister with WD40 instead, you waste allot of it here as the air just blows it away instead of to the cutter. I use methylated spirit on my mister and that works wonderfull, used it on alu for 2 years, both cools down and.. you dont really have any cleaning after.. 3 flute will work good here, as it has thicker core than 2 and 4 flute, i would also recommend to leave 0.2-3mm leftover radial and when you are done, do a cleanup pass with full depth to remove that leftover, gives a cleaner edge and wall finnish, experiment on how mutch leftover you need, if you have allot of marks from machining, you will need more to remove it in 1 or more layers in full depths. Saying that it was way to fast for a 4 flute cant be right, i cut at 2500 mm/min on 3 flute at 14200 rpm on my DIY cnc (aprox 0.052 chipload i think).. abit more sturdy than that china machine, but still. Also, those misters works well at aprox 2 bar pressure.. i have tried more and less, but with those chips 2 bar will be enough and compressor doesnt run hot on long run, you can check my channel for some of my cuts on alu, mostly test cuts.. should reckord a real cut (i have one, but my motormount was actually falling apart, so had to go very slow as i cut a new mount)

@MBcreates

6 жыл бұрын

Thanks !

@PiefacePete46

5 жыл бұрын

Kerosene also works wonders, and is more economical.

@No1sonuk

5 жыл бұрын

You can buy refillable spray bottles and 5l refill cans.

@alanhardman2447

5 жыл бұрын

I have a bit of experience with machining, myself - since 1975, and I've NEVER seen a better cutting fluid for finishing aluminum than solvent. Yup, the solvent used in a standard shop parts washer. I, too, would simply suggest slowing the spindle speed and adjusting the feedrate for the proper chip load... Just sayin'!

@satxsatxsatx

5 жыл бұрын

wd40 is available as liquid www.amazon.com/WD-40-Multi-Use-Product-One-Gallon/dp/B00HEVDA1O/ref=sr_1_3?gclid=CjwKCAjw0tHoBRBhEiwAvP1GFbUFRfxqSIwgnscSV1CV_J_rMRl9mmQu38MU2CaW_n8wXQ6mM_nhXxoCdZcQAvD_BwE&hvadid=233970095727&hvdev=c&hvlocphy=9028059&hvnetw=g&hvpos=1t1&hvqmt=e&hvrand=7849571284478519757&hvtargid=kwd-322422269664&hydadcr=947_9642198&keywords=wd40+liquid&qid=1561636301&s=gateway&sr=8-3

wow seeing this really makes me appreciate my workbee cnc even more. I have been cutting 8mm aluminium plate for the first time and its been cutting very clean and within +/- 0.02

Very usefull information! I recognized the packaging: Aluminium op maat. So you are dutch!

@huseyinyigit86

3 жыл бұрын

kzread.infoabout yes

Nice video. I have one of those mist kits laying around waiting for drilling/tapping, or 3d printing something to attache it,.. I like your approach better. I can do zip ties all day long. :D What is your spindle speed? I've had the same issues with clogging. I actually found it easier to cut steel because of the aluminum clogging the bit.

Nice

Looking into getting a home/hobby cnc machine. How solid are these frames? Is this style better than the all extruded aluminum frames? Mostly looking at it for sign making. Though, I do intend a little work on aluminum pieces.

the "Clogging up" is called chip welding, its caused by poor chip evacuation and recutting chips

Have you trammed the system? May help with surface finish

Did you ever find a supported rail to fit the 6040?

also with the rotation of the bit clockwise, you would be better cutting in the same direction, or you will get that bounce

Its a weird when I see these machines in action. Usually the floor damn near buckles under my Japanese iron when we take a cut. I can feel the machine rapid from 40 feet away and chew chips as big as rose pedals. At times flames rip forth as if you have ruptured hell itself. This is where I started, and its much gentler haha.

How powerful should the motor be if I want to cut 20mm thick aluminum?

hi at what rpm do you mill please , thanks

Hello friend, excellent video! I have a question, what features does your cnc have? I mean the type of engines you used and the guides, thank you!

@MBcreates

5 жыл бұрын

Thanks ! it's a chinese CNC 6040 with a 1500 watt spindle and nema 23 stepper motors. you can see more info on ebay goo.gl/cT5X4E

Try switch the tips, some materials are actually easier to cut without hss or ceramic, and just go for hardened old steel, especially cutting inconel and chopping things like aluminium

Sure wish I could figure out how to get my 3040 up and running...Really tricky figuring out all the steps to get these going. Major big time stuck getting mine going. Guess eventually I will have to buy the motion controller for 80 to 100 bucks...then buy Mach 3 or 4 for 175 to 200...Super stoked seeing your's running.

@MBcreates

5 жыл бұрын

Hi Tod, That sucks. Have you tried posting your questions on forums/Reddit?

@toddspeck9415

5 жыл бұрын

I am slowly figuring this out...so stoked...learning so much as I go. I am determined to be good at cnc.

always assemble the tool SHORT as soon as possible. Try one flute bit... 4 flute is for finish work.

I'm a tool and die maker. You should be climbing, not the positive way . You will find much better cut . Because it will clear the cutting chips.

how much watt of rotor can do aluminium milling?

Yes the feed speed is way too high for this machine....slowing down would produce better results and not stress the machine

I have the 4030. The Z-axis can be moved upwards by about 2 mm. The ball screw is not fixed. Maybe this is the case with you and the vibrations are caused by it. I have not milled aluminum yet. With wood I had no vibrations. The spindle is too heavy.

Great video sir , I like to know about machine, How can I ordered it? Price of machine and other required end mills or cutters. And like to see machining video on Jewellery product of silver or gold.. Plz send mi information

1-3mm aluminum/3.175mm single flute. 4-6mm/4.762mm single flute:cut length 8mm. 7-10mm/4.172mm single flute: cut length 12mm.

take the spindel speed 4and 5000 drop the feed made cuts to o.5 rough the bulk of the aly out then drop to the face and take one cut for finish

Couple questions. Where did you purchase that mill ? How much ? Can the spindle speed be reduced to 2,500 to 3,000 ? Was it already assembled ? Is it all aluminum ? Thank you PS. A good place to start for speeds and feeds is : Cutter speed ( every material has a cutter speed. You can look it up in Machineries Handbook ) x 4 divided by diameter = RPM If it's a lathe, that's the RPM of the stock, if it's a mill, that's spindle RPM. I've got 40 years as a machinist, CNC machinist, production engineer, and that has always been a great speed to start at. Tweak as necessary.

@alanhardman2447

5 жыл бұрын

I tried that twirking stuff - it doesn't work on alummm. Never mind... I see now you said TWEAK. And he said he got it for about $700.

What software do you use?

Thanks a lot

@MBcreates

4 жыл бұрын

Welcome!

Use 6061-T6 for milling. We use 4 flute on it all day long with zero issues of packing. Your packing was from to high feed and not enough cooling.

@conceptinterface

6 жыл бұрын

Yes, 6061 seems to be the most popular alloy for machining: T4 or T6. But 2011 is also highly rated for machinability (I don't know what temper).

Can we use 1.5mm diameter cutter easily, what u suggest

Is your 6040s the version will ball screws or just regular trapezoid thread?

You need to reduce the speed rate, reduce to 1 floot the endmill this endmill is special for aluminum alloy

hey , does it work with steel ?

Hi, how many watts is the motor?, thancks

Interesting video for novices in CNC. Could I give the link to the velocity table ?. Thank you

@user-sw2ol6jx8p

4 жыл бұрын

Here are the cncmachinediy.com you need, not only the complete range, but also a lot of models easy for novices to master.

whats the name of used software to design shape ?

what program did you use for generating gcodes?

Another tid bit is, instead of using High Speed End Mills, use Carbide 2 Flute End Mills. Yes it's a bit higher in price, but the tool will outlast high speed and you will see chips instead of dust as you called it. Also by adjusting Speeds and Feeds to accommodate the Carbide End Mill will be neccessary. Good Maching.

@thebeststooge

5 жыл бұрын

Single flute is what is suggested for aluminum from everything I have read or seen.

@alanhardman2447

5 жыл бұрын

Use carbide on aluminum ONLY if the tool is coated. And never m,ore than 3 flutes. High speed steel 2-flutes work just fine.The real problem is that 4-flute endmills don't have proper chip clearance for chip evacuation, causing material to "roll" forward and back into the web, packing it full and overheating the material. It then "plasticizes", or gets "gooey" and stalls wimpy spindles, or breaks wimpy endmills.

where did u buy from... any link?

What do you mean that the X axis is "unsupported?" Is it not connected to the two 15mm plates on the sides?

Hi, I noticed you are using a 6040 CNC router with Fusion 360. When you when to post process in the CAM part of the software, what machine did you select please?

@mitsuman007

5 жыл бұрын

You usually select whatever software you are using to drive the machine. I use LinuxCNC so I pick that. UCCNC and Mach3/4 are also on the list.

Good

Used 1 flute 18000rpm and cutting speed lower a little bit :)

Replace air and oil by olive oil to prevent stickies and for briant finish, it's not a joke a working alu. over 10 years and it work.

@thebeststooge

4 жыл бұрын

Olive oil is pretty expensive (even the cheap Walmart kind) for this.

@WurstPeterl

4 жыл бұрын

The Best Stooge Most highend aluminum manufacturing uses olive oil tho. Atleast everywhere where I‘ve been in Germany. One place I‘ve seen even used macadamia oil which is at least 60€ a liter.

@rpgallagher7628

4 жыл бұрын

You just spray it with olive oil? You don’t need the air?

I wish you would have gave the specs of your machine. It looked pretty beefy and I would have thought it would have easily handled the job so I am a bit disenfranchised looking at the purchase I made… I am looking to do similar work flows.

Hi friend, thank you for these videos. I had a 3040 CNC but could barely cut 3mm 6061 with. Is the the 6040 more powerful? Did you upgrade the router or any other components to be able to cut this aluminum. Thank you!

@lukebrown6913

2 жыл бұрын

Hi, I have just bought a 3040....what's the wattage of your motor?

was that first cut at real time video? I was thinking that feed rate is terryfyingly fast! Then snap! haha. At a guess i would start at a quarter of that feed rate.

Dude the best possible solution for cutting aluminum alloys is one flute carbide endmill. Expensive but with proper coolant mist you can cut with 3mm diam. thickness of 2mm with 1000mm/min with high rpm, more than 20000. Or with 4mm diam. you can easily cut 5mm at 500mm/min. I use an alcohol solution for coolant and it works wonders. But it is essential to have a rigid machine. If you can move something by hand then you have problems....

@dejanbrice8774

5 жыл бұрын

Strongly agree also! I used to use two flute and they where ok but damn single flute is a whole new world! 24000rpm pushing 1000mm/m, 2mm doc and 3mm over with a 5mm bit!

we use to use a water-soluble oil turned the water creamy whitish but had great lubrication and cooling characteristics.. Can't remember what it was called, anyone else out there knows?

Why not mist cutting oil. I've heard that single flute bits are the best. You need more stiffness in your cnc machine frame.

I have a 6090, cut aluminium all the time. 2.2kw spindle, run at full rpm, single flute carbide cutters, depth of cut ~20% of the width of the cutter, cooled and lubricated with an ethanol spray.

@MBcreates

5 жыл бұрын

Which brand end mill do you use? Link?

@law-ofohms7815

5 жыл бұрын

Datron, and don't balk at the price, well worth it. Or go 2 flute ebay carbide. but be highly polished. Its a router, not a mill. Milling tools with tight helix are not that great. What I look for is a 'slotting' cutter, as most of the work is cutting out the shape, not side milling a chunk of aluminium.

what is the name of the 6040 cnc router your using

For aluminum there is special one flute cutters.

I use an air tool oiler for the misting unit, and olive oil for fluid. 1 drop every 10 seconds or so, no smell, no sticky residue, and wipes clean. No health effects either!

@MBcreates

6 жыл бұрын

That sounds pretty good. I’m going to test it. Thanks for the tip!

What this cnc model plz

A shorter tool and a zirconium nitride coated carbide endmill will make a big difference. The shorter cutter is 8x stiffer for every halving of length and the zirconium nitride keeps the aluminum from sticking to the cutter. Makes a world of difference in aluminum.

if you put an indicator against the spindle and can push more than .002 or more forget aluminum untill you beef up the router, you need enought chip load to not wear the end mill, I just scrapped a 25 year old 3,000 lb box way machining center, rigid is everything for metals, cheeting will just cause fustration, coolent wont help cutter deflection

No oil in mist, full glog. Then , step down 1.2, step over 3, tool dia 4-5 mm. Speed 500mm/min, spindle speed 15-20 x1000 rpm

What's the size? Is it too loud for a flat?