i have a kukirin g2 pro and while riding it shut off and tried turning it on and the display turn on for a second and shut off and did that multiple times and after a while trying the display stop lighting up...... help pleasee any tips be appreciated

Thank I’m rewiring it rn having a little difficulty can anyone kinda help guide me you helped me a lot Ty

@RickyEats

3 ай бұрын

motor phase wires may be different but just switch blue with green and vice versa to make them go forward

Thank you!!

I've tried to follow your video but try as I may I keep getting two errors on the display; the first is (!) which means the brakes are giving input and a spinning screw icon. Before I changed the controller these icons never appeared.

@RickyEats

Жыл бұрын

Must be the throttle one of the cables are not connected properly, brake cable same

Plus when I'm on single motor the front wheel only spins iv seen other videos and there it's the back that spins on single motor, is this a problem

@RickyEats

Жыл бұрын

Swap blue and green and green and blue

Bro tengo yume 13 y las luces no me ensienden me puedes ayudar? Me imagino algun cable se Habra quemado puedes darme una mano con eso? Gracias

@RickyEats

11 ай бұрын

Pero corre bien la scooter?

Ok so , when you are connecting that first white & black cable you said cuz you're doing it in order , 1 of those controllers has 2 of those white and black cables and it looks like your other 1 is already connected to where it needs to be but I need to know where both get connected because I dunno if you're starting from nothing at all connected on both controllers or if u already have half of it done and your camera doesn't focus well enough to be able to see all the colors of cables when your grabbing cables in the back saying this 1, that doesn't help me at all. If you had a good in-focus closeup shot of connections made after you connected each 1 that would have been more helpful. I'm trying to get my Y10 rewired the proper way because I'm not getting any voltage so I think I may have something connected wrong

@RickyEats

Ай бұрын

White / Black wire from controller b goes to Controller A white/black wire. Basically everything is Color coordinated

@RickyEats

Ай бұрын

the wires you see already connected are gray / black that connector has a splitter which connects from controller A to the eco/turbo mode button to controller B , you want to connect the longer section of that wire to the turbo button and the splitter to the controller B. Look closely i mention it on the video

@robyntaurusbeatz703

Ай бұрын

@@RickyEats thank you but that's not which wires I was talking about. The ones I am confused about are definitely not get , they are blck/white also. I know u did mention the black and grey wires but on my controllers, I will have to check which 1 but one of my controllers on my Y10 has a black & white coming out of the controller right on top of another black and white. The black & grays I have as well but there are 2 black & white on 1 of my controllers. No way is it gray, it is black & white. Both sets.

@robyntaurusbeatz703

Ай бұрын

@@RickyEats this may still help me figure it all out because it just so happens that after I thought I had the essentials all connected I found that the eco/turbo connections still weren't connected anywhere but I think maybe our scooters have different wiring because as I mentioned in my other reply, I have 2 sets of black/white cables coming out of 1 of my controllers and only 1 set of black/white coming out of the other controller. Plus, my eco/turbo splits into 2 different connectors at the end requiring 2 different places to connect to obviously. Both are 2-pin connections.

@robyntaurusbeatz703

Ай бұрын

@@RickyEats ya know what, I'm watching again over and over and now that I've watched several times I can see that 1 (only 1) of your controllers has 2 sets of blck/white cables as well just like mine. It may be on the other controller but I can see it and it's not connected to anything but how do we know which set to connect it to when connecting controller to controller? Lol, u say it's common sense to color match up the wires but there's actually several connections that aren't connected to the same color so that's not accurate. Anyway I'm pretty sure I also just saw the eco/turbo cables in that handful of of cables you left out that you said was pretty much all my lights and I need to connect my eco turbo so hoping you have 1 on those connections now because literally nobody has posted how to connect the wires on any of the wiring and you're the only one. I can't wait to learn the complete wiring diagram for these so that I can post clear videos and explanations for those who need help. I'm almost there. I can't even get the manufacturer to send me a wiring diagram. It's ridiculous. I'm not gonna go out and buy an entirely new scooter just cuz they wont send me the wiring diagram if that's what they think lol.

I have a gbooster I bought from someone and when I opened it up the wiring is terrible I'm new to scooters and wiring so havnt a clue what I'm looking at yet to sort it cant find english tutorials anywere, when I had it opened I pressed the front light on and it smoked abit in the wiring do you know what this could be?

@RickyEats

Жыл бұрын

What brand?

@littlemagiic7255

Жыл бұрын

@@RickyEats kugoo g booster

Light video no? I can't find the right connection for the rest o the video you didn't show hehe The 3in 1 switch for light horn and turn signal don't turn on or off, only work with I connect directly to the 60v black and red 😰

@RickyEats

Жыл бұрын

Get replacement those often burn thats why i have now an external battery for the lights

Hello. Love your videos. Question. I have a yume scooter my throttle not turning on or my lights. Can you help. I messaged yume but no response yet

@RickyEats

Жыл бұрын

Sorry for the delayed response try checking the throttle connectors let me know !!! follow the cable it should be a split two connectors that connect to controller B

@pevadventuremadness

Жыл бұрын

@@RickyEats thank you. Will try

@RickyEats

Жыл бұрын

@@pevadventuremadness my display failed as well i will make new video with the fix !!! My battery is fine display shut off and doesn’t turn on i have a fix , new video coming

Bunch of room in there huh? Think i could fit a 3x9cm 12v 10-15A converter in there for led lights?

@RickyEats

2 жыл бұрын

A bit tight but I think it would fit if not externally with a be would be good

Hi I'm having trouble wiring up my new controller that I got from yume any chance of a in depth video of the controller wires or a diagram atall I'd really appreciate the help

@RickyEats

2 жыл бұрын

Send email

@toddstacy5564

Жыл бұрын

​@@RickyEatshey man . Really informative video... I've got the yume x11 and wanwkndering the same thing... Is there any sort of wiring diagram or ANYTHING to go by to hook my scooter wiring back up

@RickyEats

Жыл бұрын

@@toddstacy5564 kzread.info/dash/bejne/aqCTlauFY7Gvp7A.html check that channel

@johnnyvonrebel

Ай бұрын

Hey my dude. I know you're probably tired of answering people's questions about their scooters. And I hate doing this to you. But, I need some serious advice and guidance regarding two JP controllers that read 60 volt 50 volt DC and 28 amps 1200w. I have looked everywhere for a 60 volt 28amp JP controller and no where can I find the schematics. The LCD screen turns on, the key fob turns on, the LCD reads error 6. No movement with motors. Can ya do me a solid and help a guy out with my inquiry? I'd highly appreciate it. Thanks a bunch, either way. And in closing, I leave you with my utmost respect, Johnny

@RickyEats

Ай бұрын

@johnnyvonrebel what model of YUME scooter do you have boss!?

e normal os fios aquecer... como modar a rotacao da roda

@RickyEats

Жыл бұрын

Azul y Verde - Amarillo y Amarillo - Verde y Azul

where can i buy a controller? my controller broke but don't know where to buy or find the same one

@RickyEats

Жыл бұрын

For the Y10 US $65.07 21％ Off | JP 52V 25A and 48V 20A Electric Scooter Electric Board for 52V dual motor 48V single engine scooter Controller mother board PCB a.aliexpress.com/_Ew4pR6L or yumeway.com

Hey sweety you seem to be pretty familiar with the wiring in the scooters and I have a Yume Y10 and I fucked up the rim and broke it , requiring me to have to replace the entire motor after having to drill out a stripped bolt and then still attempting to secure the busted outer rim with bolts caused the threads on the back side holes to strip and no longer hold the screws 🙄🫣It's been a headache trying to figure out a way to avoid having to replace the entire rear wheel motor hub but I finally went and found a replacement motor the same size and I'm switching these motors out. I have 2 questions maybe you could help me with. 1st is that I notice when opening everything up and getting a look at the motors wires that I'm replacing that the manufacturer didn't have the wires matched to their color exactly and I'm not sure if they did this in order to trick us in the case that like myself I went somewhere other then them to purchase new motor for cheaper or what but the yellow is connected to the yellow main wire but the blue wire is connected to the green and the green to the blue. I checked the controller for the front motor and same thing??🤔Do you think I should connect this new 1 reversed like they have it or do u think that's what they r hoping I do so that it doesn't work? lol My 2nd question is that in this new motor there is a bundle of 5 thinner wires that have pins on the end already and they even gave my a white plug in order to install the pins with and after some research it looks as though these may be what they call the "overhaul wires" ...but my scooter doesn't have these wires coming from the front or the rear motor and instead are both only connected by the 3 thicker main yellow, green & blue cables. So should I just leave these smaller pinned wires alone and not attach them anywhere or do they need to be connected somewhere ?? Sorry for all the questions. I mean as for the extra wiring I will find out soon enough here if it's gonna work without those wires being connected but yeah lol . Just come over and I'll make u dinner while u help me with my scooter 😂.

@RickyEats

2 ай бұрын

Do the same wiring as the front wire , it should be Yellow to Yellow , Green to Blue , Blue to Green to make the hub motor go forwards , the old y10 models don't come with hall sensors so you can cut the connector off and extra wiring. And just connect the motor phase wires ; green blue yellow to the controller nothing else. My Y10 is from the first year the company launched so i'm still using split rims and no sensor hub motors as it came like that

@RickyEats

2 ай бұрын

Also when testing out controllers , What i would do is swap the controller B to the working controller A to the front motor if the motor doesn't engage that mean mostly like it needs to be replaced usually controller B goes down that's wa way to test a bad controller

@robyntaurusbeatz703

2 ай бұрын

@@RickyEats awesome Ricky, thank you!! You answered my questions. I have the earlier version of the Y10 also so that's what had thrown me off. I'm not in need of testing any controller though because I just needed to replace the rear motor. Not even because the motor was having issues either because the original was working perfectly fine. Its just that the housing around it was damaged with the threads being stripped unable to get the bolts to lock in at all so I had no choice other then to replace the entire motor hub while they don't sell just the housing of the motor by itself..😔. If you ever get the time, a video of the wiring explained and shown more detailed for both controllers would be very helpful and appreciated. I just want to make sure I have my wires connected correctly and I think I may have messed them up back when I shorted em out because it doesn't look like my wiring for the lights are in the same controller as the front motor like you explained in your video so now I'm all confused with these wires. Like the voltage wiring from where I put the key in to turn on. I dont think I have it plugged into the right cables and I'm frustrated now trying to figure out the electrical on this thing!! 😫

Hi, yu can help me for my yume scooter? He have 3 month. Is brocken down

@RickyEats

2 жыл бұрын

What’s wrong with it ?

@pppp5493

2 жыл бұрын

it was wet in the rain

@RickyEats

2 жыл бұрын

@@pppp5493 battery good? Motor???

@pppp5493

2 жыл бұрын

@@RickyEats the battery does not want to charge but the charger is good

@lazriosjenkins1436

Жыл бұрын

isnt there warranty

A mi me parece una [M] y el motor de atrás no quiero funcionar bien, tú sabes cómo arreglarlo ?

@RickyEats

2 жыл бұрын

Que tiene brodel!? Hace para moverse o esta trancado?

@rolitoo5578

2 жыл бұрын

@@RickyEats ya lo fui a chequear el motor de atrás se daño

@RickyEats

2 жыл бұрын

@@rolitoo5578 no hace nada ???

@RickyEats

2 жыл бұрын

@@rolitoo5578 puede ser el controller B bro a mi me paso algo similar , cambia los cables del motor de atras al control A a ver si corre

@rolitoo5578

2 жыл бұрын

@@RickyEats ya lo lleve a que un profesional lo vea y el hizo todo eso y es el motor que se daño

Code 02 nd 06 error scooter won’t move

@RickyEats

Жыл бұрын

Open the battery cover

I hate how JP controllers react/feel and sound, they're the first thing that were gone off of my scooter

@RickyEats

Жыл бұрын

Yea rumbling noise! I started leaving P7 setting at 0

@BH4x0r

Жыл бұрын

@@RickyEats no i mean the acceleration by the slightest throttle touch mainly

@RickyEats

Жыл бұрын

Yea they bad at low speeds

Hi, I was wondering if there are any fuses in the wiring for the lights? I attempted to connect 2 ends of wiring thinking it had come undone and I shorted out all my lights except my turn signals so now , no brake light , tail lights or head lights. It fizzled and smoked a tad bit when it happened so I'm pretty sure I burnt out the circuit. Just hoping there are fuses in between somewhere to protect or do I have to purchase an entirely new controller to repair?

@RickyEats

Жыл бұрын

I think by default this controller over time do burn with the lights connected to the controller !!! That way of wiring caused me a controller as well and seems to be a pattern ! I ended up adding a 12v batt in a pouch and connected all my lights since then i have not one issue

@RickyEats

Жыл бұрын

No controller should still be good

@robyntaurusbeatz703

2 ай бұрын

@@RickyEatsok so if I accidentally plugged 1 of the lights cables into the wrong wire where I believe it touched positive to neg and vice versa , popped and sparked from the opposites touching and now none of the lights on my shit worked, what would I be needing to replace in order to fix the issue?? Maybe the little wire harmed fuse thing that connects the cables ??

@RickyEats

2 ай бұрын

I have some videos that the manufacturer sent me ! I can send them to you so you can have a more idea how everything is wired

All my connections are good but the motor run on reverse

@RickyEats

Жыл бұрын

ok no problem put green on blue , blue on green , yellow to yellow

@mendomsa

Жыл бұрын

Ok let me see

@mendomsa

Жыл бұрын

It’s work , is safe I don’t want talk again also when I connect the brake sensor show me a error and speed controller no work if I disconnect the break sensor is safe for use

@RickyEats

Жыл бұрын

Just remove it you don’t need sensors anyways