MS170 muffler exhaust mod to expel exhaust more effectively
Жүктеу.....
Пікірлер: 19
@adelarsen97762 ай бұрын
I've done the side adjust and fang on my 2 170's. I have not done the exhaust yet and may never. Good video though especially the bit about making the exhaust port holes too big. :-)
@barktwicemofo2 ай бұрын
great info and video , the dog spikes ?? , stihl, or ?? , another great poster is donyboy 73 , he says and shows the part # s 4 the saw ... thanks!!
@ChainsawUsers
2 ай бұрын
Yes Stihl dog spikes
@Abc-kn5wj4 ай бұрын
Did you keep the stock carburetor when you did that exhaust mod or did you ring out the main jet or you keep everything bone stock
@ChainsawUsers
4 ай бұрын
All I did was change to bigger mesh so the saw will breathe a litter better and retune low and high. It runs slightly better not a huge Increase but better small Increase than no increase
@johnchuck95733 ай бұрын
I had to drill my screen.I will look for the bigger screen the next time I'm at the hardware store.
@ChainsawUsers
3 ай бұрын
Yes drilling can work also pulling out every 2nd or 3 rd wire also works
@johnchuck9573
3 ай бұрын
@@ChainsawUsersI've found since switching to a cleaner oil I don't have to clean it as often.Thanks for this channel.
@johnchuck9573
3 ай бұрын
My buddy told me to use size 20 stainless steel mesh.
@ChainsawUsers
3 ай бұрын
@johnchuck9573 a few sizes up will do the trick 20 stands per inch sounds about right
@lion195578 ай бұрын
What is the size of t spinner you used for muffler nut
@ChainsawUsers
8 ай бұрын
Muffler nut is standard fitting
@ChainsawUsers
8 ай бұрын
6mm
@lion19557
8 ай бұрын
@@ChainsawUsers thank you so much dude 👍
@Aisajoni
2 ай бұрын
I had 8mm and no net at all.
@ethaneth856 ай бұрын
Did you adjust the carb afterwards?
@ChainsawUsers
6 ай бұрын
No because it just breaths a little more. Many people go to far with these mods and yes they require tune up
@phantomshtter2 ай бұрын
I drilled the dead center hole and far left, far right middle holes to meet their corresponding holes, kept the stock screen and flared the vents slightly. I knew that goon that carves out the entire grid ruined his saw.😅 It's amazing how ignorant people are to air/ fuel ratios. Anytime you open intake or exhaust on an engine, you're leaning it out. Lean is mean... until it's burnt up the motor.
@ChainsawUsers
2 ай бұрын
That said means bark box egan straight shot will all lean out the motor. I only flared the vents also just a bit
Пікірлер: 19
I've done the side adjust and fang on my 2 170's. I have not done the exhaust yet and may never. Good video though especially the bit about making the exhaust port holes too big. :-)
great info and video , the dog spikes ?? , stihl, or ?? , another great poster is donyboy 73 , he says and shows the part # s 4 the saw ... thanks!!
@ChainsawUsers
2 ай бұрын
Yes Stihl dog spikes
Did you keep the stock carburetor when you did that exhaust mod or did you ring out the main jet or you keep everything bone stock
@ChainsawUsers
4 ай бұрын
All I did was change to bigger mesh so the saw will breathe a litter better and retune low and high. It runs slightly better not a huge Increase but better small Increase than no increase
I had to drill my screen.I will look for the bigger screen the next time I'm at the hardware store.
@ChainsawUsers
3 ай бұрын
Yes drilling can work also pulling out every 2nd or 3 rd wire also works
@johnchuck9573
3 ай бұрын
@@ChainsawUsersI've found since switching to a cleaner oil I don't have to clean it as often.Thanks for this channel.
@johnchuck9573
3 ай бұрын
My buddy told me to use size 20 stainless steel mesh.
@ChainsawUsers
3 ай бұрын
@johnchuck9573 a few sizes up will do the trick 20 stands per inch sounds about right
What is the size of t spinner you used for muffler nut
@ChainsawUsers
8 ай бұрын
Muffler nut is standard fitting
@ChainsawUsers
8 ай бұрын
6mm
@lion19557
8 ай бұрын
@@ChainsawUsers thank you so much dude 👍
@Aisajoni
2 ай бұрын
I had 8mm and no net at all.
Did you adjust the carb afterwards?
@ChainsawUsers
6 ай бұрын
No because it just breaths a little more. Many people go to far with these mods and yes they require tune up
I drilled the dead center hole and far left, far right middle holes to meet their corresponding holes, kept the stock screen and flared the vents slightly. I knew that goon that carves out the entire grid ruined his saw.😅 It's amazing how ignorant people are to air/ fuel ratios. Anytime you open intake or exhaust on an engine, you're leaning it out. Lean is mean... until it's burnt up the motor.
@ChainsawUsers
2 ай бұрын
That said means bark box egan straight shot will all lean out the motor. I only flared the vents also just a bit