While isopropyl (ISP) alcohol can loosen the adhesive under the battery, on some phones it could seep between the rear screen layers which can discolor or ruin it (I've seen it happen to some people). While most ISP will evaporate, it may contain a small amount of water which is really not good for electronics. A better solution is to simply heat up the front of the screen to about 90C on a digital heat plate which won't affect it at all, it will loosen the glue under the battery enough to be able to remove it easily with a narrow metal spackle tool. This method works even on the hardest to remove batteries, on iPhones you'd heat up the back of the phone instead. ;)

@PBKreviews

Жыл бұрын

Yup, it can happen. Best to use little amounts if using it.

Please tear down Moto Razr 40 and moto razr 40 ultra

@PBKreviews

Жыл бұрын

I might do the 40, but ultra has already been done by others. I will see. :)

🎉love fromBangladesh 🇧🇩🇧🇩

@PBKreviews

Жыл бұрын

✌️👍

These phones are decent for the price

@PBKreviews

Жыл бұрын

yup 👍

@jamesmorriss9565

Ай бұрын

The Walmart Ladies told me I HAD to have them activate my phone, that I could not use my old SIM card. 😅 Took out the included SIM card Put in the one from my moto e6. Bob's your uncle. Gee... I did not have to pay Verizon $1000 for a phone that dies in the first three months.

Well built phone. I like the coolings.

@PBKreviews

Жыл бұрын

👍

How do you just take the cover/lense off to clean behind it, you mention it can be done without disassembly, but it would be good to see it done, and how do you replace the adhesive?

@PBKreviews

5 ай бұрын

It would be best to take the back housing off for that since removing the camera lens off and re applying adhesive will be more work and complex. If its broken and you're replacing it, its another story but since this back cover doesn't have glue or adhesive holding it down, its just clipped on aside from the fingerprint sensor which has a little bit of adhesive holding it to the back housing. So just heat the fingerprint area a bit with a hair dryer, then remove the sim try, use a pry tool to get it in between the back housing and the frame of the screen right by the sim tray where the plastic is thinnest so you can easily get it in, then run it along the sides and release the catches. When the back is lifted from the frame, push in on the fingerprint scanner to pry it off the back and then fully remove the back housing, clean what you need to and place it back on snap it in place and you're done. But for the lens removal same, just apply heat, use a razor blade or x-acto knife and pry it from one corner of the camera lens glass to peel it off gently. Applying new adhesive you will need to probably order replacement adhesive tape or camera lens glass which comes with the adhesive pre installed. You can find parts for it at mobilesentrix.com

👍

@PBKreviews

Жыл бұрын

👍

@pixelman8044

Жыл бұрын

@@PBKreviews 👍

Why not upload moto g play 2023 unboxing?

@PBKreviews

Жыл бұрын

I didn't get this phone boxed, got the phone by itself so yep :)

@TalkingGames0005

Жыл бұрын

​@@PBKreviewsLol 😂😂😂😂

@PBKreviews

Жыл бұрын

​@@TalkingGames0005😅

@TalkingGames0005

Жыл бұрын

​@@PBKreviews Why not unboxing the phone lol 😂

Do you know where it keep the extra storage beside the sd card because I'm trying to remove the pattern lock after factory reset

@PBKreviews

4 ай бұрын

Its on the ROM or storage chip which is soldered to the main board under one of the covered shields and is not user removable or replaceable.

Hola 👋 Amigo Excelente Video de hoy Martes de Celulares Review Motorola en Reparación 😁🙏❤️📱

@PBKreviews

Жыл бұрын

Hi, thank you :)

@luisfernandomaicanhernandez97

Жыл бұрын

@@PBKreviews Hola 👋 Amigo Feliz Martes ❤️

Just the information I needed. Somehow cracked the glass covering my main camera. Need to find replacements and a good how to.

Do you have tips on if my moto g plays charging port wont work unlessni wiggle the cable

@PBKreviews

4 ай бұрын

You would probably need to replace the sub board/charging port board. Here is a link for the part: amzn.to/4ach9yk

Are any of the components interchangable with the moto g pure?

Excellent video. Unfortunately my phone went all black - but it charges. First step to a fix? I banged it against the table.

@PBKreviews

7 ай бұрын

Thanks. Might be frozen, try holding vol down and power together for 20 seconds see if anything happens. If not might be a bad display.

@mariannebjork3778

7 ай бұрын

Thanks so much for replying

i just fixed this yesterday lmao

@PBKreviews

Жыл бұрын

haha sorry I was late.

@JohnnyboiLikesDeezNutzz

Жыл бұрын

@@PBKreviews the owner of it broke it right after he bought it lol

@PBKreviews

Жыл бұрын

​@@JohnnyboiLikesDeezNutzzlol damn that sucks, at least you were able to fix it!

@JohnnyboiLikesDeezNutzz

Жыл бұрын

@@PBKreviews ya

Where is the SIEM number on the battery

Nice

@PBKreviews

Жыл бұрын

👍

i need XT2163DL motorola mein board

Next teardown on M34 5G please.

@PBKreviews

Жыл бұрын

Done. :)

you gave iphone better repair score than this one that dont have any glue?

😮😢😮

@PBKreviews

Жыл бұрын

👍 :)

@IBRAHIMROTERWOLF

Жыл бұрын

@@PBKreviews 🌹🌹🌹