Listen at 1.5x. trust me.

@iliketurtles4761

2 жыл бұрын

Let me personally thank you

@RELOADEDEDER

2 жыл бұрын

Good call

@wyskii

2 жыл бұрын

Wow. Thanks

@twistedgaming9832

2 жыл бұрын

Thanks

@Lucky_Logan

2 жыл бұрын

Good save.

there's so many professional mechanics in comment sections it's always so helpful.

Sounds normal to me, but can visually see it’s too tight too. Thats the 1st thing I saw.

Most of noise seems to be from the top part of the chain just behind the front sprocket knocking against the chain guide on top of the swingarm, which is completely normal. Under load most of that contact would go away. You can test this by going down a steep hill with the bike in neutral and the engine off.

@BhatakantiEkPravas

2 ай бұрын

I'm riding on highway of clutch engaged no chain noise if I give Accelaration it's starts rattling. Chain and sprocket completely new not used even 100km even nicely lubed.

Useful video. Thank you buddy

I recommend to check the slack when rear wheel is on the ground Frequent you will see that some of the slack is gone and your chain is to tight

Do you pressure wash your chain when you clean it?

Chain is too tight i can see that straight away

@ChillyDippers

2 жыл бұрын

Yup. Chain needs a little slack. If he continues to run that he is a. Prematurely stretching the chain, and B. running a high risk of catastrophic failure.

@biesasuk

2 жыл бұрын

Yes, like I mentioned at the end it was to tight.. After more adjustments it was great

Is this amount of noise fine? My Yamaha FZ6N makes this sound now as well after tension the chain. And I mean then the sound at the end of the video. Before I never noticed any sound at al. The chain has been driven 80km with a to tight chain after loosening it again..

@biesasuk

3 жыл бұрын

Yes that means it's to tight, maybe you have to loosen your chain a little. I lubricate my chain every 500km~ and check tension at the same time. If you overtightened it for sure it will make lauder noise because it's way to tight. Hope this helps

Did you say you loosened it before this video? It still seems way too tight. I think the sound will disappear if you loosen more

Check the Washer lock "washer" on the front sprocket. It might be hitting the front sprocket nut.

@biesasuk

3 жыл бұрын

Sprocket was fine, bearings fine, all lubricated, lined up, rear wheel bearings fine.. could not figure out, but I put extra lube and loosened the chain to almost touching the body of the bike and it fixed perfectly. Was smooth and quiet after few miles riding, got fully lubricated and it worked great!

@ChillyDippers

2 жыл бұрын

Chain is TOO TIGHT !!!

on my bike im giving sudden gas while being on 2nd gear it’s giving me tak kat noise .. is it too loose side or too tight?

@JonathanSilva-yv9fl

2 жыл бұрын

Same did U solve this problem ?

My 636 has a hard plastic slider on the swingarm for it to actually run on so it does not wear out the metal

@johnny2024

2 жыл бұрын

It's crazy how my 636 makes more noise than my exhaust, it concerns me sometimes.

@jakepavlo91

2 жыл бұрын

@@johnny2024 it is a loud whirring sound isn't it! I noticed it more when moving to a D.I.D chain, maybe slightly wider or something.

@johnny2024

2 жыл бұрын

@@jakepavlo91 oh ok, I don't hear it with my helmet or without but when someone took a video of me I heard it. Oh well I'll see if I can replace it this winter.

did you fix it ? I'm having similar problem after getting a service done recently.

@biesasuk

2 жыл бұрын

Yes, just read some comments what I did and it worked very well!

@lollygaggin6332

2 жыл бұрын

It’s a tight chain problem

You should listen to the chain of my ducatis 😂 totally normal

I'm riding on highway of clutch engaged no chain noise if I give Accelaration it's starts rattling. Chain and sprocket completely new not used even 100km even nicely lubed.

@akshatchugh7953

10 күн бұрын

Did you find the solution and cause

@BhatakantiEkPravas

4 күн бұрын

@@akshatchugh7953 NO, Using it as it is. noisy

@akshatchugh7953

3 күн бұрын

@@BhatakantiEkPravas i think you would have to clean the front sprocket you have to remove the cover of front sprocket first Gear numbers must be written on it and then clean and lube the chain again it would get fized

Does a over pressed master link cause the noise?

@biesasuk

3 жыл бұрын

No had to release the chain even more, was almost bouncing and touching the body of the bike but the sound changed dramatically

@Jb-qx7mj

3 жыл бұрын

@@biesasuk you don’t want a chain that loose man that’s dangerous

My sounds like that but I wonder is it safe to drive?

@biesasuk

3 жыл бұрын

Yes it was to tight and I had to release it, once that was done all worked just fine

@valtergrins8275

3 жыл бұрын

Was the chain to tight because my new bike sounds like that?

@biesasuk

3 жыл бұрын

@@valtergrins8275 yes the chain is to tight and make sure it's well lubricated so less friction and less chance to overheat. I normally lube the chain every 500km or 300miles

hey i am facing clunk or tak tak noise on deceleration..did u ever faced this problem on ninja 300 ?

@biesasuk

2 жыл бұрын

Sorry but we sold bike long time ago. Could not check that anymore.

@BridgeIsSky

Жыл бұрын

Same, just when decelerating, what was your problem and solution?

@karanbundhela3336

Жыл бұрын

@@BridgeIsSky Mine silencer catalytic converter gone for toss got changed header pipes under warranty problem solved.

Wait this is too tight? Mine must be wayyyyyyyy too tight then

Hope you changed it

@biesasuk

3 жыл бұрын

Yes like I mentioned the chain was to tight, so I loosened the chain and added extra lubricant and then it worked perfectly!

I don't like the look of that split link - seems to be mis-aligned next to the links on either side. Please check brother.

@biesasuk

3 жыл бұрын

Link was fine, I checked it. Because I replace it and the new one was very stiff at the beginning. Thanks :)

That's too tight. the chain is supposed to ride on the chain guide on the top of the swing arm.

@BINX-RR

10 ай бұрын

Did you see how much the chain moved when he barely pushed on it? This is why we have owners manuals.

@mooosestang

10 ай бұрын

@@BINX-RR I see how much the sprocket/swingarm moves side to side when he pushes on it. that doesn't look normal at all. I'd check those cush drive bushings.

There is a stiff link i am seeing

You can see stiff spots on the Chain like it needs lubed

Chain is not ligning up with sprockets

@biesasuk

3 жыл бұрын

Yes I did lined up the chain and had to release the tension.

@iliketurtles4761

2 жыл бұрын

@@biesasuk so this was the answer??? My new bike making the same noise 2002krt 400😭😭😭

The chains way too tight at the beginning of the video

A rattling noise whilst moving the bike when you are next to it is usually a sign of a chain adjusted to tight. Measure it while it is on its wheels. Having a slapping sound when driving at low speeds around 50kmh: too much slack. Pretty much the golden rules for chain adjustment.

@BINX-RR

10 ай бұрын

30-45mm more or less depending on the bike. If it’s within that spec in the owners manual it’s fine. You’d probably say my chain is waaaaaay too tight but it’s just in spec.

Looks bone dry to me lol you shouldn't be able to touch it like that without getting oily

Seems a bit tight... it needs some.slack

Just clean the mirrors and the noise will be gone right away, also adding grease on top of the seat helps , add a about half a cup of sugar on the gas tank and man that 300 will run like a 1000 for sure

Sounds normal lol.

Tigh chain + worn sprockets

@ChillyDippers

2 жыл бұрын

New sprockets. You had it in the first guess. Too tight

Chain is noisy because it is dry .Over lube this chain .

@biesasuk

3 жыл бұрын

I did and I lined up, but what worked the best was releasing the chain, was almost touching the metal on the bike

@pubgbros687

3 жыл бұрын

@@biesasuk change chain set .

@RafaelAlmeida-qo7vj

3 жыл бұрын

@@pubgbros687 did you watch the video at all?? He started the video saying that he replaced the whole kit like 2 weeks prior