Hello i like cat grader is good for work

Cantik bang Rifai manuver motorgreder cat24 m,nya nyimak aja bang top bgt👍👍

When he's completing a pass he should lift his toe prior to starting his turn. This would allow the material to flow off the heel and deposit it in the windrow without curving it at the end. Benefits of this include allowing traffic to flow uninterrupted, no need to drive over top windrow, and easier to get back on the windrow on the next pass. Many years in the 16m, h & g, but would love to try out the 24m!

@RIFAIMining

4 жыл бұрын

thank you for taking the time to view my video

@t-dog8528

4 жыл бұрын

alternatively run the tail all the way to the side and still cross winrow on inside front, it's only a haul road and on last pass run that baby out from patch up area half square on so it can be bought across patch next full cut

Mntap...operatornya hebat...slm pemula

Ini adalah teknik/metode manuver dalam maintenance jalan yang benar,Blade selalu tepat diletakkan pada windrow (gundukan2 material yang memanjang yang dihasilkan ooleh alat2 gali),dan arah manuver juga benar dalam mengkombinasikan learning wheel(memiringkan roda) dan articulation serta merubah sudut porpulsion Blade (besar sudut Blade terhadap center line /garis tengah frame (rangka) 👍👍👍

@ianyan2664

5 ай бұрын

Bang belajar dimana bang apa ada bukunya

Very good operator to run a grader non stop and maneuver it hats off to you

24 M 👍👍👍

Mantap bosku semangat semoga sukses selalu🙏🙏🤝🤝👍👍

Mantap bos,,salam dari jambi

Muito prazeroso ver esse monstro em ação

First time I have seen the Articulate in the middle. Frame ! Very efficient turns. My Father was a Equipment operator during the Korean War. Army Corps of Engineering. He ran Cat Graders Pans and D-7 & the first D-8 Cat Dozer that were sent became His Machine. ! Just Lost Him. 11/23/19 Sure Miss You Dad...

@ockeyboys4579

4 жыл бұрын

Sorry to hear about your father. The newer ones do actually articulate and makes it so much easier aswell.

@lbbradley55

4 жыл бұрын

Ockey Boys Thank you Yeah they are interesting. That's a BIG GRADER Dad was very proud that first D-8 CAT they sent them became his machine. I have a few photos of him with it. They all had cable lift and clutch and break to steer them. ( Clutch pedal and lever break ) L R No Hydrologic nothing. They also had a 1 HP Brigs & Stratton pony start engine they had to crank up to start the Cats. I still find videos of them.

Really productive and efficient. Sometimes you need to be able to get the job done quickly. Good skills.

@RIFAIMining

4 жыл бұрын

Thank you for taking the time to view my video 🙏🙏🙏

Bersyukur dan beruntung bgt dilatih sama beliau🙏

@RIFAIMining

4 жыл бұрын

Josss

Subhanallah berkahnya Semoga sehat selalu dan bahagia ❤️

very nice work style well done

A monster grader, in highly capable hands ...such a joy to watch!

@RIFAIMining

6 жыл бұрын

Oliver Wabwire thank's Mr oliver

Jos Gandos...🙏👍

@RIFAIMining

3 жыл бұрын

Josss

Keren mobil alat berat nya, 👍👍

Mantap bos

Hdir bang rifai,pemula yg sdah sukses

In civil we would call this a “cut/fill transition”. In mining we call it a road, “more delays more pays” I would suggest a “square box out 📦”_cut, followed bye a genuine hard rock base equaled by compaction of the surface layers -2mtres minimum.

Selamat berkarya terus mantap vidionya good👌🏻 saodara lama nyimak kembali😎 Sadara baru ayo merapat kita ngopi

Selalu safety dalam bekerja ya bosku. Salam sukses dan membawa berkah bosku. Mampir great kn jalan saya ya bos ku

Fast, accurate operation of a big, capable machine.

@RIFAIMining

6 жыл бұрын

Tu te Kohe thanks Mr Tu te kohe

@huvvy

4 жыл бұрын

Why? Cause he learned how to turn around and roll a windrow on a haul road

Kereeen pak sugi

Mantap Dan Keren

Keren lanjut kan kawan biar semangat saya bawa kan kopi hitam yah biar tmbah semangat terus👈👍🙏

What do we reckon, 3rd gear?

Great job!!!

@RIFAIMining

7 жыл бұрын

thank's mr.jhon M evangelis,I do this to give an example of how to combine leaning wheel anda articulated and moldboard correctly when manuvering in order to produce the effectivitness of motor grader 24M

Mantap..

Claro ejemplo de cómo sacar la mayor eficiencia de la máquina, sin duda un gran operador

@RIFAIMining

7 жыл бұрын

thank's enrique 13,i'm from kalimantan north - indonesian as instructor heavy equipment the coal mining bigges company at kalimantan

Mau buat apa tu kak, keren alatnya

skilled driver, nice.

@RIFAIMining

6 жыл бұрын

ferze001 thanks Mr.ferze001

He’s a smooth operator!!!

@RIFAIMining

5 жыл бұрын

Thanks mr.curt schnitzer

@t-dog8528

4 жыл бұрын

what? you didn't see the bouncing

Goodd👍👍👍

I'm thankful for this video that is imparting knowledge to me and other friends who are interested in gaining useful knowledge.

@RIFAIMining

5 жыл бұрын

คนนี้ที่ใช่ Love love thank you for taking the time to see my video, hopefully useful

@Lovelove-je2ji

5 жыл бұрын

Dawet Hitam tarakan l like to see you very glad that you convey the knowledge knowledge ... l am in Thailand without a large scale model to see it ... l thank you too. I

@lendavidhart9710

5 жыл бұрын

@@RIFAIMining Sug LC, Thank you for posting very nlce video work and grader work, thanks for sharing.

I run a 160M, love these machines.

@RIFAIMining

4 жыл бұрын

Wow...160 M good machine...

@RIFAIMining

4 жыл бұрын

thank you for taking the time to view my video

@kapoorsingh3229

3 жыл бұрын

Good👌👌

War biasa Manuferx..👍👍👍

this is beautiful

@RIFAIMining

4 жыл бұрын

Thank's

Great bit of driveng........ And good we tip of doin a haul road... Tanks for sharing....

@RIFAIMining

4 жыл бұрын

Thank you for taking the time to view my video about efective grading motor grader

@robbiekennedy1029

4 жыл бұрын

@@RIFAIMining I am a dozer driver but I b on graders on and off and I think thats a great clip of how to keep grader goin on haul road wit out stoping..... I am lookin forward till My next outting on d grader... Cheers man

@RIFAIMining

4 жыл бұрын

Good,i'm from Indonesian Kalimantan east coal mining,i'm as trainer equipment

Mantab... Keren Videonya...

@RIFAIMining

9 жыл бұрын

Makasih sudah meluangkan waktu buat melihat video saya......

@arturolopez3898

7 жыл бұрын

sugiono tc that's what I'm talking about.

@RIFAIMining

7 жыл бұрын

+Arturo Lopez where is your come from?

Can't believe it's 6:32 am in South Africa, I need to go to work and I'm watching a video of a grader up and down moving the dirt instead.

@RIFAIMining

4 жыл бұрын

thank you for taking the time to view my video

Mantap

Mantep bosku..👍

Sangat keren,untuk buat jalan.

Mantap I like

Good to see a grader operator who can keep the machine moving constantly. Two-bit wannabes you see everywhere with 'years' of experience who have to stop the machine to set the blade before each run and still dig the toe in the whole way 😡😡

@RIFAIMining

7 жыл бұрын

As a trainer motor grader i tried to do job well and profesionally so as to be used as a reference an usefull for other,thank for your comment....

@RIFAIMining

6 жыл бұрын

Sam Grimshaw thank's guys for taking the time to see my video

@Grabatire

6 жыл бұрын

Not every job site that provides that opportunity, space-wise, but nice to watch an operator who can take advantage of the machines capabilities.

@rossgray3070

5 жыл бұрын

Go and do some final trim along side kerb and get it ready for asphalt with a couple of culled sacs and intersections in it, I can tell you it don't happen like that video, not when you are trimming to 5 mm.

@RyTrapp0

5 жыл бұрын

@@rossgray3070 At the end of the day, all that matters is the quality of the finished work and how quickly it can be done - style points don't end up on your pay check, that's a fact not taking anything away from this operator of course

🤔Strasbourg ✋

Pokok.y wOw bgt..... Gimana cara mengoprasikan.y???jadi pengen belajar

@RIFAIMining

4 жыл бұрын

Wahhh....yang koment operator senior

Kita adalah teman. Terima kasih😁

Smagat

I have never seen this large scale car in Thailand. Thanks to this video clip for people who are interested in the knowledge....Thank you.

@RIFAIMining

5 жыл бұрын

ผู้ ใช้งาน thank's Mr.after see my the video

@Lovelove-je2ji

5 жыл бұрын

Dawet Hitam tarakan l thank you too. This video clip to your friends have been watching ... Thank you

@RIFAIMining

5 жыл бұрын

ผู้ ใช้งาน I made this video in terms of demonstrating the correct and efficient operating techniques so that operational costs can be minimized. This video I want to give to East Kalimantan Indonesia

Semangat terus kawan,, salam kenal

👍👍👍

جميييييل

Nice operating he's done that once or twice before

@RIFAIMining

5 жыл бұрын

Thank's mr.david...😀😀😀

Does anyone know what blade on this grader is equv to in a dozer For egs. A D- 4 or 450 just asking if any one know. Thank you

@RIFAIMining

3 жыл бұрын

The blade on this grader measures 7.3 meters in length and approximately 1 meter in height. the equivalent of a dozer can be compared to the size of the blade.

Thank's arsyad mahmood....

@atiladorsay3478

4 жыл бұрын

Sugiono LC hi is he doing laser levellin?

Josssss...

Do you cut, repair and spread or just cut to one side?

@RIFAIMining

4 жыл бұрын

I only demonstrated how the technique of absorption is effective

a U turn whit a grader nice job sir

@RIFAIMining

6 жыл бұрын

Antoinecorner thanks Mr.antoinecorner

شكرأ

@RIFAIMining

5 жыл бұрын

Thank's

A Williamson turn on a motor grader, well done.

@RIFAIMining

6 жыл бұрын

Zingara Joe thank's mr.zingara joe

A god among men

@RIFAIMining

7 жыл бұрын

halo...tippmannallstar,where do you come from?

@tippmannallstar

7 жыл бұрын

sugiono tc Alberta, Canada

@RIFAIMining

7 жыл бұрын

+tippmannallstar i'm for kalimantan north Island, indonesian

@richardpantin1108

6 жыл бұрын

How many years of experience do you have operating Grader?

กรีดทางลงให้เพราะไหร

Not bad

@RIFAIMining

6 жыл бұрын

J j601 thank's guys

Mantap, kawan baru nyimak 🙏mampir kang

Hello, are you America or Canada?

@RIFAIMining

4 жыл бұрын

I'am from Indonesian country

im a Grader operater.but want to operate like that. nooo reavers

@RIFAIMining

6 жыл бұрын

Grader Cutter this technique is actually easy to use only a combination of very precision

Mantaaap

@RIFAIMining

4 жыл бұрын

Joss

Mau nanya ni pak...? Ini dimana project nya pak...? Pengen belajar ni pak mengendari motor gradernya pake joys stick ya pak..?

@RIFAIMining

7 жыл бұрын

Ini saya buat diberau kalimantan timur khususnya Buma-Lati waktu saya mendemonstrasikan teknik manuver yang efesien dengan menggunakan motor grader M-series,video ini untuk siswa2 saya yang harapan nya temen2 operator dapat mengaplikasikannya dengan baik dan benar2 efesiensi saat mengoperasikan motor grader

Buat jalan tol lur..??

Wow.... bagus ini klau mau di pakai usir orang demo yg anarkis 😅😅😅

nice

@RIFAIMining

5 жыл бұрын

Thank's mr.dheeraj patel

24 m lati kayak nya

@RIFAIMining

3 жыл бұрын

Siap Betul om

Andai kalo aku bisa kerja ditambang 😃kalo dikebun medannya sulit2 😂

@RIFAIMining

5 жыл бұрын

Semua bisa kerja ditambang...semua area kerja sama resiko dan bahayanya, yang terpenting adalah bagaimana bekerja dengan aman pada area high risk

@adaffalahardhana8686

5 жыл бұрын

Mantap Jiwa, Doain aku ya pak semoga kapan hari bisa kerja di tambang 😁😁😁

@RIFAIMining

5 жыл бұрын

Aaminn...

Las llantas delanteras están invertidas en la dirección de giro los tacones de las huellas de las llantas tienen el sentido invertido, eso provoca una trepidación en toda la máquina.

@albertogarcia5276

5 жыл бұрын

Imagino que te referiras a que los neumaticos delanteros estan montados al reves. No se que significa trepidacion pero en una maquina sin traccion delantera que esten montados al reves poco importa

@opieteller5952

5 жыл бұрын

Se montan al revés para q tengan más tracción, en todas las motos q e traído están así por q da mejor funcionamiento

@joseferreyra3231

4 жыл бұрын

@@opieteller5952 es verdad afirma mas la máquina

He's good, good operator, but personally on that last pass I would have turned out to my right and come back straight at the windrow.

@RIFAIMining

4 жыл бұрын

Thank's Mr,Nicolas

@huvvy

4 жыл бұрын

Yeah wow he can turn it around and roll a windrow, dont have to be a skilled operator to do that

Itu mau di buat ap to mas kok di ratakan??

Novice.

@RIFAIMining

2 жыл бұрын

Yes

No way

RAPI...How long you have been operating grader Pak? Gk minat adu Nasib d rantau kami Pak? Hehe.. Salam dr Melbourne Australia 🙏

@RIFAIMining

6 жыл бұрын

Muhammad Ali ini video waktu saya mencontohkan teknik grading dan manuver dengan menggunakan Caterpillar M-series,ini sebagai alat peraga untuk para operator untuk penyegaran tentang teknik operasi yang benar dan efisien,saya sangat berminat sekali untuk melihat temen2 yang ada diluar Indonesia sebagai ajang silahturahmi dan sharing tentang teknik operasi yang baik

@alimuhammad35

6 жыл бұрын

Dawet Hitam tarakan Oh begitu, klo Sy operator Excavator Pak... Bisa dong bagi2 ilmu nya grader pak, sbb Sya Penge dkemudian hari bisa jd operator grader juga. Klo Disini udah mulai bnyk yg pakai 'Trimble Grade control' or GPS sedikit diManja.

@RIFAIMining

6 жыл бұрын

Muhammad Ali boleh,ini wa saya 082218451797,saya juga sambil belajar terus mencari ilmu yang baik

@masmaskuri4973

5 жыл бұрын

Very nice... Pak tlg bagi video tutorial P2H GREDER 24M dari bawah sampai masuk kabin

@RIFAIMining

5 жыл бұрын

@@masmaskuri4973 untuk p2h,dasar tahapannya cuman ada 4: 1.pemeriksaan mengelilingi unit 2.pemeriksaan sebelum engine hidup 3.pemeriksaan setelah engine hidup 4.pemeriksaan setelah beroperasi Untuk masing2 unit pastinya berbeda2 bagian yang dichek

अरे भाई साहब इस ग्रेटर से डंपिंग तोड़ती दिखाओ

Must be a new operator, they gouge their heel or toe on almost every turn cutting a ditch lmfao

@RIFAIMining

4 жыл бұрын

thank you for taking the time to view my video

Definitely not the operators first day.

@RIFAIMining

4 жыл бұрын

thank you for taking the time to view a video of the operation of the Caterpillar 24 M motor grader

@xreconusmc3156

4 жыл бұрын

Josh Edwards nah about 32 plus years of service

#SALAM KENAL GOTONG ROYONG YUK.

queloco Qoooooo

@RIFAIMining

7 жыл бұрын

halo. .daniel garces

Nice, I am from Algeria. Please contact us soon

@RIFAIMining

4 жыл бұрын

Okey

Mantap