I was running this saw for about 2 hours at about a 30-50% duty cycle kzread.infoUgkxfQm1wmg0ItKDLavxj1nXtQY9HP7EF504 and it did a great job. I used the lever for the built in sharpener to clear chip buildup out more than to actually sharpen the chain. It managed to cut some hardwood stumps much larger than it's size without bothering the neighbors with hours of 2 stroke noise.

Here is a bit of interesting history for you. In 1971 McCulloch introduced the SP 125 chainsaw. This saw , now 50 years old, put out 10HP at 10000 RPM, and with the factory installed 101B kart powerhead put out 15HP at 12000 RPM. That is why it is still the most legendary saw ever made.

@TheWoodsmanMilling

2 жыл бұрын

I'll have to look for one of those.

@tnbrfller

2 жыл бұрын

Very interesting, iv'e not heard of that Saw. We used to run the 084 back in the day, but falling 14 foot Cedars is pretty rare now. The 881 would be a treat to run, and see how far it's come. Have a great Day.

@keatonlingafelter4023

2 жыл бұрын

@@TheWoodsmanMilling good luck lol

@keatonlingafelter4023

2 жыл бұрын

I’ve been looking for a sp125 for awhile. Hard to find

@mrobsoletesvintagehomestea9156

2 жыл бұрын

only made 3 years, and most were used up in the big timber, not leaving many for the collector today.@@keatonlingafelter4023

Great info!

Sent in my brand new ms880 with under 5 hours on it ported by Ripsaw. Expect it to be able to blow this saw away. I had a ported 088 and an 090av and before that a Super Whiz 88. Love the biggies.

One of the few people on KZread that know how to run a saw

Look into a Maxflow air filter setup for it. Especially in a milling environment. The factory filter seems to grab the larger chips in the pleats and gets clogged too fast.

@Brothers-se4rc

3 жыл бұрын

We are constantly looking for a quality high flow after market filter. We currently swap filters throughout the day. We will check them out. Thanks!

Just two questions. Firstly, what's the difference between a MS 881, and an MS 881 'Magnum', or are they both one and the same? Secondly, how long before the injected version of the 881 is in production? Thanks.

STIHL MS 881💪🏻❤️

@parkerdean5888

3 жыл бұрын

Are they sponsored?

an absolute beast.

Keep it up stihl!!

That clutch is jingling and jangling.

great for pruning

I don't know how you did that cut without any eye protection! 😎

@dgj32784

2 жыл бұрын

Chaps? Those blue jean won't stop much. Only takes once and it won't be pretty.

👏👏👏

👍👍👍 👋

Big Beast saw😉😉👍🏼👍🏼

Badass saw! BTW THIS IS M A G A COUNTRY! 🇺🇸 BECAUSE THE SALT MUST FLOW!

สุดยอด👍👍👍👍👍⭐️⭐️⭐️⭐️⭐️⭐️⭐️❤️❤️👍👍

Since it has a diagnostic port, does that mean it's fuel injected?

@Brothers-se4rc

3 жыл бұрын

No its not. 500i is the only fuel injected currently. Apparently its supposed to optimize fuel/air mixture among other things.

@TheChube25

3 жыл бұрын

@@Brothers-se4rc Interesting, thanks for the reply 👍

Hye frinds..chainsaw new sthill very2 power..How much is this chainsaw??

The beast!

Either you've created a map of Antarctica or the world's largest pizza serving plate.

Is it any better than the 661? which is much cheaper ☺️

@elielcassimiro55

2 жыл бұрын

E quanto custa um desses?

That makes my ms 391 look small lol

What is the price of ms881

@hughjaynis4864

2 жыл бұрын

Here in new Zealand its about 3.5k

Sounds like a small dirt bike.

@chadklaren9537

Жыл бұрын

Small dirt bike that thing is 121cc that's the size of a full size dirt bike.

chainsaw and a .40 please break in

Does your sister know you are using her saw

@Brothers-se4rc

3 жыл бұрын

Your mom lent it to me if you must know... just kidding. Thanks for the comment!

Stihl ms 500i

I'm going to put one on a motorized bicycle

You should have slabbed that log!!!

@Brothers-se4rc

3 жыл бұрын

We plan on it! We cut the end to remove a rot section.

Yipes ! Stop yer cut before you put it in the dirt. Roll the log over and finish. Can you say peavey. The biggest saw in the woild aint the fastest cutting saw if the chains dull. It's a boat anchor.

@Brothers-se4rc

3 жыл бұрын

We were in some pretty thick fescue, but no argument there. Your are correct. Although, you may be paying too much for your boat anchors. Thanks for the Comment!

One word…. Poulan

That saws a sweety

Shtil no one amazing

070 090 way better

3120 is still better

@pramiumyoutube1182

3 жыл бұрын

Not

@Broddi169

3 жыл бұрын

@@pramiumyoutube1182 butt hurt won't change it koolaider

@TheWoodsmanMilling

2 жыл бұрын

@@Broddi169 are they still making the 3120? I heard that it was no longer in production.

@Broddi169

2 жыл бұрын

@@TheWoodsmanMilling I'm still seeing them on dealer floors

@TheWoodsmanMilling

2 жыл бұрын

@@Broddi169 I might have been told false information, then.

its wormy soft maple

husqvarna 3120xp will out cut it

@johngardea625

Жыл бұрын

Hell no I own both saws and this shits on the 3120xp