your first method wasnt that bad but wedi sells boards that are 1/8 thick and if you just buy that, and cut it to size you can make any mozaic fit perfectly 👌🏼... when i was learning tile the contractor taught me to put vinyl floor tiles behind the mozaic to build it up but i learned quickly that that is not the right way to do that

@LandbergTileTV

5 жыл бұрын

Yes, that Wedi trick is a great idea! I wish our local tile stores carried 1/8 inch Wedi panels. We only have 1/2 inch. Maybe we should order a few 1/8 panels and hold them aside for this type of circumstance. Funny story on the vinyl floor tiles to build out! That cracks me up! 👊👊👊 thanks for watching

@OleksiyBaydala

5 жыл бұрын

Jetboard has 1/8th thickness backerboad as well, if you have your local tile vendors selling it. It's much cheaper too, only about $8 for a 3x5 sheet.

@LandbergTileTV

5 жыл бұрын

wish we had jetboard in our area, sounds like a good deal!

@tylerstorer287

5 жыл бұрын

Bad ass tip man...my life just changed forever...

@thetruthyes

5 жыл бұрын

@@OleksiyBaydala yes 1/8 jet board is what I use. Works everytime.

Was installing mosaic strip tile in my shower for an accent. After one beer I quickly determined it sucked, removed the tiles and scrapped out the thinset and washed the tiles in a bucket. Luckily I only had one more beer when I decided to do that so the thinset had not setup. After my third beer I got on my laptop and came upon your video and used method 1. I'm 66 years old and I have been doing it wrong for decades. Also used the lasko levelers. What a wonderful time we live in. Thanks!

You guys totally saved the asthetic appeal to my tile job in my basement. I wanted to put in a striped horizontal mesh mosaic and attempted yesterday (I mow grass and make billets but I’m savvy) and upon my attempt it was sagging slightly and I learned I was using a square notch too large instead of a V notch but more importantly, placing a backing on this will help immensely. It’s very similar to the first description you gave in the video. Although my mosaic is raised above my surface tile as is so that doesn’t matter so much. But this will make things much easier. Thanks again.

Thank you! I have been scratching my head on how I was going to install a band of mosaic around the surround, without a mess. Perfect solution for my case. Thank you.

Thank you so very much😭😭😭!!! You just brought this diy-er back to life!🤸‍♀️🤸‍♀️🤸‍♀️

great tips, excellent demonstration. Probably too difficult for the DYI but great for occasional installers and pros. Thanks

Great video, just what I was looking for! Thank you and God bless

Should watch this video before lol 😆 t installed in my shower 🚿 😌 Thanks for the video

This helping me so much! Thank from Kosago Vietnam with love!

Best tips and tricks video iv ever watched thank you for taking the time to make this 🙏🏼

OMG your mosaic tile application is ingenious!!!

@LandbergTileTV

3 жыл бұрын

Thanks!

Very nice n clean! Just how I like it. Thx for the idea. I’ve always made a screed

Great idea, just what I needed. I had all my 12x24 tiles underneath the accent line like this and the tile was thicker than the mosaic like this, I added a layer of thin set and flattened it out behind where I’m putting the mosaic tiles to keep it out farther and flush to the main tile, but this is a better idea for sure, I used the kurdy strips and niches over the red wonderbaord because you can’t find the kurdy foam board at HD or Lowes. If they had 8’x5’ sheets at homeD or lowes id get that and just use 3 pieces, cut out the niches and you’d only have the corners to tape with the membrane and bottom of shower pan. I think you can order it but it would be so much better to have the sheets in the big box store. Going to use this method now, but the only this it having to wait for it to dry and then set it. It takes time, but it’s better then sagging mosaic tiles. Just do it on the floor over the kurdy tape and set them perfect then thinset them to the wall. Thank you

Oh! Look its work! Great, this video help me somuch! Thank from Kosago Vietnam with love

Much gratitude....knowledge I will need in the coming weeks, but hadn’t yet given any thought.

This was so very helpful, thanks a lot.

Thanks for this tutorial. Excellent!.

Great job ... thanks for sharing... Usually I use 1/8 inch jet board ... sturdi and inexpensive.

I was just face with this problem with my first ever tiling attempt. Thanks for offering me away to possibly get out of this pickle. Tomorrow will be an interesting day.

@LandbergTileTV

5 жыл бұрын

Yes sir, hope the video helps. Thanks for the watch and comment 👊

I used this trick today....also you don't have to clean all the thinset out of joints....I have 2 40" panels drying ready to install tomorrow....worked like a charm

@LandbergTileTV

3 жыл бұрын

Sweet, happy it helped! 👊

Awesome idea. I will be cutting 6” strips of the kerdi membrane to glue onto 1” glass accent pieces.

i like both options, but would probably go with number 2. thanks for the tips nice video

Method 1 worked for me. 🙏🏿 Thank you! I tried the 3/8 kerdi membrane and found the kerdi band method better for me (1st time tiler). I was able to control the amount of thinset behind the mosaic w/o all of the thinset coming through. With the kerdi membrane the wall was a little wavy, I worried when I would put on thinset to compensate it would come through so I ended up using method 1 and it worked. Make sure to clean the prep surface after so extra thinset doesn't stick band to drywall Thanks again!

Great work fellas, thanks for the tips and tricks!

@LandbergTileTV

9 ай бұрын

Our pleasure!

Wow good technique ! The installation is flawless great idea!

@LandbergTileTV

5 жыл бұрын

thanks! 👊

@josephv5346

5 жыл бұрын

really ?

Good video dude thanks good tips

great video. what type of thin set that you recommend to use on the tile?

What a great idea!

Thanks for the tip, I always learn something from your videos. Great job guys.

@LandbergTileTV

5 жыл бұрын

and I always appreciate the view and your comments! Thank buddy! 👊

I use saved Ditra leftovers for shimming out. At 1/8" thick it's usually right on!

@LandbergTileTV

5 жыл бұрын

Yes sir! We do the same (I should have added that to this video) 👊

The way I usually do it, I cut about a 4 foot piece of kurti and glue them to that and then cut it how I need it the next day in individual pieces. But I like this idea as well

Great tips 👍

Love this job

Wow I never thought of putting kerdi on the back of the tile sheets. I wish I'd known that before I installed the last shower kit I did. Thanks a million!

@LandbergTileTV

5 жыл бұрын

Well now you know! thanks for the view comment! 👍

@thomasnorthcastle4130

5 жыл бұрын

BCMountainMan67 Did you know that Schluter offers FREE weekend training? They pay for your HUGE hotel room just for you, breakfast, lunch and dinner. You also leave with massive amounts of knowledge as well as tools, shirts and bags!!!

@LandbergTileTV

5 жыл бұрын

So true and so fun! I had shrimp, steak and cocktails on our first Schluter workshop 👊 In and out was lunch for the next day👊

Very good idea man, i used this methods 3 years and salve a lot hours job.

@LandbergTileTV

5 жыл бұрын

Yes sir it does!

I know I know...man, when you're a one man crew, its extremely hard to get any sort of content...ESPECIALLY when you're a perfectionist. I KNOW you know what I'm talking about. If it's not "groundbreaking" it's not worth it. Content IS content though. I still have cameras rolling ever day. Timelapse everything. Someday we just need to collaborate and make an all time epic tile video.

If it's eye level, just use a strong vct. Skim with thinset. You can cut it with a straight cutter and in certain applications, can stack tile above that immediately. You're welcome! 😃

Awesome thank you!

What size V notch did you use for the kerdi band and Glass tile. Plus did you use whatever white thinset you had close by OR? I seem to have issues where I have the 1/4 inch plus space for the glass but once I apply the thinset on the wall I start getting too far out

Beautiful 👍🏻👌

Will that work with Oceanside paper face mosaic glass ? I just wonder if the kerdi band orange will bleed through ?

What do you use to get that perfect spacing for the mosaic?

Good job! Ty

Did flopping the membrane crack the thinset at all? Thx

Cool video. Tnx.

How did you keep the tiles above from sliding down?

Landberg ,Best!

Oh look. Finally a product that Kerdi is good for.

@LandbergTileTV

5 жыл бұрын

Lol

@mattjudy4037

5 жыл бұрын

What dont you like about kerdi? My favorite rough in material by far. Only one I will use unless I absolutely have to use something different.

What size trowel do you use to put that mosaic up on the wall

When answering a couple people who asked about what thinset you used (and some not sticking) you answered non mod, then in another you answered modified...So which is it?

That lippage looked like a lot more than 4mil of the kerdi strip . Does the strip just give you ability to cake on thinset on its back to make up for the thickness ? I'm using this trick for my project now just so I can align my floor to ceiling mosaic up before putting it on wall. Woo. This seems like it'll help great. The thickness does not vary from surrounding tile , aside from different trowels sizes for mosaic and 12x24. With the kerdi band attached does that mean I can stick to 1/2 trowel for mosaic too ?

Thanks for the tip Love your videos Can I use any mortar with the kerdi band? Thanks

@ghassanco1

5 жыл бұрын

Kerdi prefers unmodified cement. But you can use any cement with it.

A variation on screeding thinset is to skim the wall area with thinset and then put wall mud (fat mud) into the area and screed the excess off. Once the wall mud is stiff enough, go ahead and install the mosaic inlay.

This tip was killer

I am going to look up the suggestion you made but did not demonstrate of letting a shallow coat go first My mosaic is 6 bands of glass rectangles so it it shorter than my rubber backed float, I will use it upright from the top to bottom and try to not push the mosaic as deeply at the flat tile above and below when I set it. fingers crossed.

What if I just installed a mosaic and haven't grouted...any way to remove it to try this trick? Thinset has dried already...

Thx!

hi there! what do you mean when you say were just gonna screw and thin set to the wall? do you use screws also? dumb question lol?? im sorry ,great job guys! im gonna go with trick number 2 backerboard first trick scares me lol you have a real talent thank you!

Man, you’re good

Thank you

very nice ! thank you .........

@LandbergTileTV

5 жыл бұрын

Thanks for the watch and comment!

Kerdi mat! Of course! Hope this comment finds you well. You guys saved me!

Another method you can add to the list is using schluter ditra. I used this method recently and it worked well. I have used the qt inch backer board before but this time it was causing the mosaic to come out further than the large format tile. If I remember correctly the ditra is only about an 1/8th of an inch (or so) thick and it was quick and easy. Btw, love your channel. Its been helpful.

@LandbergTileTV

4 жыл бұрын

Great idea, thanks!

@scottyee707

Жыл бұрын

Just saved me a trip to the store

Looks good.

@LandbergTileTV

5 жыл бұрын

thank you sir 👊

Plastic or metal lath, can be used to buildup some thickness, it is similar to Kerdi method so it also adds structural rigidity.

@lulutileguy

5 жыл бұрын

not in this aplication inconsistent requires experience and tools pneumatic stapler for example been using maplath since conception and 2.5 pound mesh 30 years would use lath on whole wall with plywood and tarpaper like at my own home main shower ceiling to then 1 metre porcelanosa that shower 10 years old 6 showers day lath good but not for unversed. why i do this because had huntwood put in beautiful cherry kitchen needed 3/4 plywood for upper cabinets and cabinet installer very picky thank him for that cheers

@shanebrown2963

5 жыл бұрын

BlahBlahMan Yeah keep the metal out of the shower. Gets wet it will rust and give you a shit job

nice work

@LandbergTileTV

5 жыл бұрын

Thanks buddy! 👊👊👊

Do a video on using metal/cast stone tile trims (Nichetile) with the mosaic borders.

@LandbergTileTV

Жыл бұрын

will do

I started using this methos about 5 years ago but I like I use Ditra install on the wall backwards and then comb my motar onto that and set my tile to that. I used the Kerdi method but Ive found some of my tiles fell off when carrying so now Imainly use the ditra on the wall.

@LandbergTileTV

5 жыл бұрын

Great idea sir, thanks! 👊

Where was that tile from?

Hi, Great video. If my tile and mosaic glass tile are same thickness 1/4" can I just use the same 1/2 trowel and both will essentially be the same level right? My tile is 12x24 so I'm using a 1/2" trowel.

@vapdivrr5656

4 жыл бұрын

In most cases, installing glass mosaics with a 1/2 trowel is not a good idea. It's simply to much thinset for the sheets and you will have thinset oozing from every joint

Nice work ...myself and and a friend of mine just did this technic thought we were the first tho ..guess not ..

Thank you for sharing your tip. Learned a lot !!

@LandbergTileTV

5 жыл бұрын

You're welcome, thanks for the view and the comment! 👊

I have an aqua defense waterproofing layer on durock and would like to use this method for a vertical waterfall band. Aqua defense calls for modified mortar but kerdi band calls for unmodified. Which would you recommend (A) between the aqua defense and kerdi band and (B) between tile and kerdi? Thanks. Great video.

@LandbergTileTV

3 жыл бұрын

Use modified, will not be a problem.👍

I always used a very thin 6 inch wall tile 6mm thick put it on first and then the mosaic on top and that made nice and flush with the thicker wall tile

@LandbergTileTV

5 жыл бұрын

Nice idea, thanks!👊

Love the videos. You have definitely inspired me to experiment more through the “Tips and Tricks” series. One last quick question: Are you religious in using the Schluter thin-sets with the rest of the Schluter products? If so, which one? If not which one?

@LandbergTileTV

5 жыл бұрын

No, we rarely use Schluter thinset. We typically go Custom modified and non-modified or Laticrete.

@zipyourlib8370

4 жыл бұрын

(I know this is an old comment replying to) Yeah Mapi makes a great thinset, "ultra-light" modified LFT, tile doesn't sag, thin granulation sands in mix excellent for tapping concrete board and screeding with..

The kerdiband technique works well, I tend to be faster if I just build a jig the fits the depth of the mosaic. Also need to waterproof the mosaic again after penetrated with the screws.

@LandbergTileTV

3 жыл бұрын

Agree, we screed it with a jig more often than not.

Loved the video, for option 2. Does it make sense to waterproof the second board? Will the integrity remain strong without waterproofing it? Or does it not matter because it was not the wall being hit primarily with water? :) loving the series!

@LandbergTileTV

4 жыл бұрын

No sir, not necessary to waterproof the second board. That's simply redundancy. Thanks for the watch! 👊

Fucking sweet trick bro I wish I would have seen this vid at the beginning of the day I literally just got done installing mosaics on a job ,, this is why I spend allot of time on utube

How do you start that row above your mosaic without puncturing your kerdi membrane? Also do you ever have any trouble with your sheets peeling apart after going through the wet saw? Awesome tip though with the Kerdi membrane, it's is a pain cleaning thinset out of mosaic tile

@LandbergTileTV

5 жыл бұрын

We use scrap pieces of tile for spacers (same size as mosaic) and continue tiling. We then install the mosaic the next day 👊

Good video

@LandbergTileTV

5 жыл бұрын

thx!

Good video, great tip with the mosaic backing. Not sure if we have anything like that in UK as I've not come across it !

@LandbergTileTV

5 жыл бұрын

Amazon.com

@peterrathbone179

5 жыл бұрын

Thanks for the advice, I will ask next time I go for tile stuff ! And of course online why I never thought of that ha ha . cheers all .

I tried the first method, followed it exactly. It doesn’t seem to have bonded well. I’m afraid to install it. The good news is the mosaic now has a thin layer of mortar on the back, enough to stop it from squeezing through. I think I’m gonna pull off the kerdi.

Thanks for the smart tips. Is the backboard waterresistant?

@LandbergTileTV

5 жыл бұрын

Yes it is, thanks!

Привет,коллега!Отличная работа!

@LandbergTileTV

5 жыл бұрын

that's tight! 👊

I do something like that I also grout it also so its stiffer

The trick I use float with cement using a t piece of wood I cut the same thickness of mosaic and install

You got Jack Black to narrate!? That's Awesome!!

@LandbergTileTV

3 жыл бұрын

lol I get that all the time, love Jack Black!

Curious about how you say "glued" to the kerdi membrane. Are you using a polymer modified thinset as your "glue"?

@LandbergTileTV

5 жыл бұрын

Yes, thinset is used as the glue 👊

Silicone mosaics to a strip of 3mm marine ply. The silicone acts as an added waterproof protection, Did mine years ago and no problems!

What kind of adhesive did you use for A) Adhering the Kerdi together, and B) Attaching the mosaic to the Kerdi? Thanks. Looks like a technique I will use.

@LandbergTileTV

5 жыл бұрын

Schluter set, or any non mod thinny..

@conniefromthefarm

4 жыл бұрын

@@LandbergTileTV newbie here: what is a non mod thinny? ty, I'm guessing thinny means thinset.??

I wish I know what type of tile that was! It’s pretty I’m struggling to find tile that I like. It seems like everyone wants a white bathroom

Hi, did you use normal thinset like the same thinset as the 12x24?

@joshuawilson2362

4 жыл бұрын

Or do you need a different type

What glue did you add to the wall to stick the mosaic panel

@LandbergTileTV

4 ай бұрын

Thinset

Excelent.

@LandbergTileTV

5 жыл бұрын

Thank you sir 👊😎

Hello, if you can please answer my question. What is the purpose of leaving the space in between tiles for the mosaic to go afterwards. Thank you for great vids

@Kayte...

2 жыл бұрын

Even grout lines.

@ricrdop01

2 жыл бұрын

@@Kayte... Thank you for the answer. So I would need to put some type of ledger or bar along the walls to hold the tile row above the mosaic, correct?

What brand tile leveling clips are those? They are popular with the pros but a little hard to find

@LandbergTileTV

3 жыл бұрын

Wow, that video is old...funny watching it back. Those are Raimondi clips and wedges from contractors direct. 👊

I installed my aluminum and glass waterfall tile without anything behind it. I guess I can live with the 1/4 inch difference in depth between it and the surrounding tiles. I will just grout all around the edges. In the future though, I would like to try this technique. It would greatly help by not having to spend time cleaning the mortar our between the tiles.

@LandbergTileTV

5 жыл бұрын

Yes, it definitely helps with the mortar squeezing out between the tile.

Stupid question. Is the mosaic glued to the kerdi-band with thinset?

@LandbergTileTV

3 жыл бұрын

Yes it is

Can I use these methods on a bathroom floor? I am edging the room with marble tile and planning to fill in the rest with small pebbles so I need something to bring it up to the same level as the border. ty

@LandbergTileTV

4 жыл бұрын

Yes, it should definitely work..

@conniefromthefarm

4 жыл бұрын

@@LandbergTileTV ty

Kerdi calls out unmodified thinset, but most glass mosaics specify modified or a latex admixture. Which did you use?

@LandbergTileTV

5 жыл бұрын

modified for glass..