how to replace fuel filter on mitsubishi triton Mitsubishi triton fuel filter replacing
Жүктеу.....
Пікірлер: 26
@robertboyd3213 жыл бұрын
Cheers, and thank you. There is one thing I can tell you about that bottom water sensor fitting, The main white plastic screw with the large o-ring (NOT the plastic wing nut drain tap) if it is done up too tight the plastic will crack around the sunken inside seam. It will only be a hairline crack and very hard to see in the beginning but it's quite enough to for the system to loose pressure & suck air into the system. Word of advice: anything with a "NEW" o-ring only needs to be tightened really hand tight because the rubber seals very easily and because it is new rubber, it grips tight, will not vibrate and does not come undone.
@michaelholland8252
3 жыл бұрын
Cheers, great tip mate
@darrylshelford2674
2 жыл бұрын
Filters should only be tightened by hand NOT with a spanner /wrench, also there is a bleed screw at the top of the filter housing facing the front.
@aotaryy5 жыл бұрын
Your job is nice and thank you and I am following you from Saudi Arabia and I benefited from you .. Thank you very much
@craigbennett34163 жыл бұрын
From Mittagong, Nsw Australia I Thankyou.. replace my fuel filter while watching this video.. Cheers..!!
@shannonbennett8251
6 ай бұрын
hey mate im from wollongong getting loss of power after scv and fuel pressure sensor replaced had to reset and relearn the scv throu a mechanic and his diagnostic tool because it was stuck in limp mode with engine light on. 2 days later she seems to be running with total loss of power can go over 50kmph in it atm feels like its restricted big time any ideas would be great
@tezsullivan60484 ай бұрын
Thank you. Very informative and well done 👍👍👍
@JafrinJChannel2 жыл бұрын
thank you forb thistutorial..
@87tunj6 жыл бұрын
A suggestion here for you, while you have the filter off is to test that your sensor is working. this can be done by grabbing the sensor, connecting it back up bare and moving the sensor up (as if it was floating in water) and then seeing if it comes up with the flash on the dash.
@golfwagen4173
6 жыл бұрын
I will try it, thank you
@robertgibson4494
4 жыл бұрын
Thats not what the video is about.
@antonch90786 жыл бұрын
Спасибо, лайк и подписка оформлены.
@agungrichy39445 жыл бұрын
What is the name of your tools like belt ?
@YamarajaDasaAlcyoneАй бұрын
What year triton and model is this can I ask please?
@dudleygraham717810 ай бұрын
What model is this Triton , mine is a 2003 , filter is underneath rear back door just in front of fuel tank
@domingomanguardia16642 жыл бұрын
how to flush clutch fluid for Mitsubishi strada Di-D
@johnbarber68622 жыл бұрын
How not to... Removing hoses increases chances of adding contaminants, drain tap into plastic drink bottle, loosen filter, unbolt and replace filter, unscrew air bleed near out pipe, hand pump till no air, tighten, start engine....
@nothn0612 күн бұрын
Looks like an MN triton
@justinnicholas77362 жыл бұрын
you showed us the new black filter, you removed the plastic, and now you are putting on a different filter? what happened? was it the wrong filter ?
@justinnicholas7736
2 жыл бұрын
no one else observed this ?
@golfwagen4173
2 жыл бұрын
the black filter was slightly scratched during removal and diesel leaked out. he has a very delicate body. so we had to give another one
@user-rf7sl4ly8r Жыл бұрын
A random way is not right.
@goddog475 жыл бұрын
Dankershen
@Mat-rs8yw Жыл бұрын
You guys like to think of yourselves a car guys... You might want to put the details in the title sometime. There's a few different tritons out there. Just sayin...
Пікірлер: 26
Cheers, and thank you. There is one thing I can tell you about that bottom water sensor fitting, The main white plastic screw with the large o-ring (NOT the plastic wing nut drain tap) if it is done up too tight the plastic will crack around the sunken inside seam. It will only be a hairline crack and very hard to see in the beginning but it's quite enough to for the system to loose pressure & suck air into the system. Word of advice: anything with a "NEW" o-ring only needs to be tightened really hand tight because the rubber seals very easily and because it is new rubber, it grips tight, will not vibrate and does not come undone.
@michaelholland8252
3 жыл бұрын
Cheers, great tip mate
@darrylshelford2674
2 жыл бұрын
Filters should only be tightened by hand NOT with a spanner /wrench, also there is a bleed screw at the top of the filter housing facing the front.
Your job is nice and thank you and I am following you from Saudi Arabia and I benefited from you .. Thank you very much
From Mittagong, Nsw Australia I Thankyou.. replace my fuel filter while watching this video.. Cheers..!!
@shannonbennett8251
6 ай бұрын
hey mate im from wollongong getting loss of power after scv and fuel pressure sensor replaced had to reset and relearn the scv throu a mechanic and his diagnostic tool because it was stuck in limp mode with engine light on. 2 days later she seems to be running with total loss of power can go over 50kmph in it atm feels like its restricted big time any ideas would be great
Thank you. Very informative and well done 👍👍👍
thank you forb thistutorial..
A suggestion here for you, while you have the filter off is to test that your sensor is working. this can be done by grabbing the sensor, connecting it back up bare and moving the sensor up (as if it was floating in water) and then seeing if it comes up with the flash on the dash.
@golfwagen4173
6 жыл бұрын
I will try it, thank you
@robertgibson4494
4 жыл бұрын
Thats not what the video is about.
Спасибо, лайк и подписка оформлены.
What is the name of your tools like belt ?
What year triton and model is this can I ask please?
What model is this Triton , mine is a 2003 , filter is underneath rear back door just in front of fuel tank
how to flush clutch fluid for Mitsubishi strada Di-D
How not to... Removing hoses increases chances of adding contaminants, drain tap into plastic drink bottle, loosen filter, unbolt and replace filter, unscrew air bleed near out pipe, hand pump till no air, tighten, start engine....
Looks like an MN triton
you showed us the new black filter, you removed the plastic, and now you are putting on a different filter? what happened? was it the wrong filter ?
@justinnicholas7736
2 жыл бұрын
no one else observed this ?
@golfwagen4173
2 жыл бұрын
the black filter was slightly scratched during removal and diesel leaked out. he has a very delicate body. so we had to give another one
A random way is not right.
Dankershen
You guys like to think of yourselves a car guys... You might want to put the details in the title sometime. There's a few different tritons out there. Just sayin...