Thanks for this information. I recently had a "power steering service required " message on the dash . Diagnostic said " high voltage " and "low voltage " fault . Turned out to be a fault in EPS unit . Main dealers say they never had this problem before
@MatikuOfficial Жыл бұрын
Bro which one is the one that gives the asc off? The first yellow wheel that you removed or the second one behind that white plastic things? Thanks
@Dinamikass
Жыл бұрын
Its second one, first is airbag spring cable.
@MatikuOfficial
Жыл бұрын
@@Dinamikass thanks bro
@juliandavidburbanoburbano80317 ай бұрын
Do you have the file to program the EEPROM of the steering angle sensor?
@Dinamikass
7 ай бұрын
No
@laszlohorvath3997 Жыл бұрын
Did the sensor need to be replaced? Or did you fix it? how? i have citroen c-crosser. thank you
@Dinamikass
Жыл бұрын
Its posible to fix, but you must go inside epprom chip and fix data. Before that you must try recalibrate sensor with diagnostic tool .
@bahattincam7486
Жыл бұрын
Eprom nasıl düzelttiniz
@JonathanHernandez-zv6md5 ай бұрын
How did you got to solve the Issue? Did you replaced the part ?
@Dinamikass
5 ай бұрын
Its posible to fix, but you must go inside epprom chip and fix data. Before that you must try recalibrate sensor with diagnostic tool .
@morristialaveals466 Жыл бұрын
What did you do to fix it pls
@hawkeni6475 Жыл бұрын
have you cleaned sensor, if so how
@Dinamikass
Жыл бұрын
If you need clean , you can try open it and blow with air
@scientist100 Жыл бұрын
I replaced a sensor with a used one and still giving the same codes. I'm thinking it is the power steering internal sensor in the power steering unit unless the car only needs new one and not used for replacement. Let me know what you think.
@Dinamikass
Жыл бұрын
after you change you must calibrate sensor with diagnostic equipment, also its possible you replaced damaged sensor
@scientist100
Жыл бұрын
@@Dinamikass I tried calibration but it fails. Set those codes immediately during key cycle. When I checked freeze frame the angle is read over 700 degrees but when I check live I don't see the angle change at all. Not sure which sensor sends the angle position to the scanner, it only says "steering angle" for data pid. I have tried two other used sensors but those did not talk to the scanner at all.
@Dinamikass
Жыл бұрын
@@scientist100 try to calibrate with other diagnostic equipment
@MitchellHubert Жыл бұрын
The sensor you tried to open is faulty, replace it
@Dinamikass
Жыл бұрын
i have repaired it and its works again
@hamykay2372
Жыл бұрын
@@Dinamikass how did you repair it? any problems now?
@Dinamikass
Жыл бұрын
@@hamykay2372 fixed eprom inside sensor after calibrated from new in car
@mantaskirpsas50542 жыл бұрын
Bet tipo prieš tai viskas veikė?
@Dinamikass
2 жыл бұрын
Pries vairo koloneles restauravima , taip viskas veike
@mantaskirpsas50542 жыл бұрын
Ar pataisei mašina?
@Dinamikass
2 жыл бұрын
Dar nebuvo laiko, bet jau greit, eproma reikia perrasyti
@adomasmarcelis6758
Жыл бұрын
@@Dinamikass dėl ko reikia perrašyti?
@Dinamikass
Жыл бұрын
@@adomasmarcelis6758 nes nebeina sukalibruoti, kazkas pabega
Пікірлер: 45
Thanks for this information. I recently had a "power steering service required " message on the dash . Diagnostic said " high voltage " and "low voltage " fault . Turned out to be a fault in EPS unit . Main dealers say they never had this problem before
Bro which one is the one that gives the asc off? The first yellow wheel that you removed or the second one behind that white plastic things? Thanks
@Dinamikass
Жыл бұрын
Its second one, first is airbag spring cable.
@MatikuOfficial
Жыл бұрын
@@Dinamikass thanks bro
Do you have the file to program the EEPROM of the steering angle sensor?
@Dinamikass
7 ай бұрын
No
Did the sensor need to be replaced? Or did you fix it? how? i have citroen c-crosser. thank you
@Dinamikass
Жыл бұрын
Its posible to fix, but you must go inside epprom chip and fix data. Before that you must try recalibrate sensor with diagnostic tool .
@bahattincam7486
Жыл бұрын
Eprom nasıl düzelttiniz
How did you got to solve the Issue? Did you replaced the part ?
@Dinamikass
5 ай бұрын
Its posible to fix, but you must go inside epprom chip and fix data. Before that you must try recalibrate sensor with diagnostic tool .
What did you do to fix it pls
have you cleaned sensor, if so how
@Dinamikass
Жыл бұрын
If you need clean , you can try open it and blow with air
I replaced a sensor with a used one and still giving the same codes. I'm thinking it is the power steering internal sensor in the power steering unit unless the car only needs new one and not used for replacement. Let me know what you think.
@Dinamikass
Жыл бұрын
after you change you must calibrate sensor with diagnostic equipment, also its possible you replaced damaged sensor
@scientist100
Жыл бұрын
@@Dinamikass I tried calibration but it fails. Set those codes immediately during key cycle. When I checked freeze frame the angle is read over 700 degrees but when I check live I don't see the angle change at all. Not sure which sensor sends the angle position to the scanner, it only says "steering angle" for data pid. I have tried two other used sensors but those did not talk to the scanner at all.
@Dinamikass
Жыл бұрын
@@scientist100 try to calibrate with other diagnostic equipment
The sensor you tried to open is faulty, replace it
@Dinamikass
Жыл бұрын
i have repaired it and its works again
@hamykay2372
Жыл бұрын
@@Dinamikass how did you repair it? any problems now?
@Dinamikass
Жыл бұрын
@@hamykay2372 fixed eprom inside sensor after calibrated from new in car
Bet tipo prieš tai viskas veikė?
@Dinamikass
2 жыл бұрын
Pries vairo koloneles restauravima , taip viskas veike
Ar pataisei mašina?
@Dinamikass
2 жыл бұрын
Dar nebuvo laiko, bet jau greit, eproma reikia perrasyti
@adomasmarcelis6758
Жыл бұрын
@@Dinamikass dėl ko reikia perrašyti?
@Dinamikass
Жыл бұрын
@@adomasmarcelis6758 nes nebeina sukalibruoti, kazkas pabega
@adomasmarcelis6758
Жыл бұрын
@@Dinamikass sutvarkei?
@Dinamikass
Жыл бұрын
@@adomasmarcelis6758 taip viskas veikia