Mercury 30HP EFI 4 Stroke - Impeller Water Pump Install - Lowe Skorpion
Installing an impeller water pump in a Mercury 30hp EFI 4 Stroke. I am installing this in my Lowe Skorpion 16 bass boat. Quicksilver repair kit.
Installing an impeller water pump in a Mercury 30hp EFI 4 Stroke. I am installing this in my Lowe Skorpion 16 bass boat. Quicksilver repair kit.
Пікірлер: 25
Thanks a bunch. I'm gonna do this on a 25hp mercury 4 stroke. I've never touched a outboard motor in my life but this give me the confidence i can pull it off 😄
@Subariblet
Жыл бұрын
My guess is the 25hp is the same exact process. You’ll be able to knock this out quickly.
Have to replace my water pump. I have the same motor. Awesome video looks pretty simple. Thank you for sharing friend!
Brilliant video, thanks
Thanks for the video! I just replaced the impeller only, using your directions. Took about 15 minutes and was less than $30. No more warning light or buzzer!
@Subariblet
2 жыл бұрын
Perfect!
Thank you for your great video
Sure appreciate your video my exact motor- looks really easy helped a lot thanks 👍
Great video Followed it to a t . Remember to wrap a towel around the rod while re installing pin . Or it may fall in the hole . Ask me how I know. 🤔 so mine still isn't pissing 😒. I replaced thermostat as well. Ugh. Thanks for any suggestions
@Subariblet
2 жыл бұрын
I never even thought about losing the pin down the hole. I'm lucky I was able to find it. Sounds like you got a clog in your system. I've heard bugs and sometimes weeds can get in there and clog the flow. I think I've seen videos before on how to flush it out
Thanks for this video, just curious was that just lower end gear oil you lubed on the top gear there?
@Subariblet
Жыл бұрын
I used Super Tech Marine Grease on the top gear. You can get it at Walmart. It’s cheap and highly rated. You can buy a more expensive brand if you want but this stuff works great.
I see you have a four blade prop. What size and pitch is it? Also what boat are you running? As I have a Lowe roughneck 1652 VT w/ a Mercury 30hp 4 stroke. I run a 11p three blade, but I am looking to try a four blade.
@Subariblet
2 жыл бұрын
I have a Lowe Skorpion 16. I just put the new prop on this year, upgrading from the stock 3 blade prop. The prop I bought is Mercury Spitfire 4-Blade Aluminum Propeller Prop 9.3 x 11P 25-30HP 48-8M8026655. I bought it from Amazon for about $150. Quicksilver makes a Nemesis prop that is the same for about 10 bucks cheaper, but I went with this one. So this is what I learned. Hole shot is greatly improved now with this new prop and brings me to plane much quicker. With the old 3 blade prop, I could go about 30mph. With the new 4 blade prop, I can still go 30mph. The new prop was well worth the buy in my opinion as I have noticed a significant better performance.
Nice work, no gasket goes between the lower unit when reinstalling? Just curious.
@Subariblet
2 ай бұрын
No
Does it matter what gear selection your on, do you leave in neutral position?
@Subariblet
Жыл бұрын
I left mine in the neutral position. I’m not sure if it makes a difference or not.
Do you need to drain the lower unit oil to do this?
@Subariblet
2 жыл бұрын
No
What size of pin punch did you use?
@knifeshakes1815
2 жыл бұрын
I think it’s a 3/32
@Subariblet
2 жыл бұрын
It was the 3/32. Sorry for the late reply
I have a 2008 40hp 4-stroke. Is it the same process?
@Subariblet
Жыл бұрын
I'm not sure. You could take off the lower unit to see the impeller housing. My guess is it will be similar.