Mercury 2010 EFI 60hp 4 Stroke Waterpump impeller Service
Тәжірибелік нұсқаулар және стиль
Mercury 2010 EFI 60hp 4 Stroke Waterpump impeller Service, Complete step by step removal of lower unit and impeller replacement. Work on your Outboard Waterpump and Impeller
#photography
#conservation
#drone
#worldheritage
#worldheritagesites
#barrierreef
#worldheritage
#tropicalisland
#australia
#queensland
#australia
#doityourself
#outboardmaintenance
#mercury
#yamaha
#honda
#suzuki
#tohatsu
© DaintreeJD 2017. All rights reserved. Any reproduction or republication of all or part of this video/audio is prohibited.
Пікірлер: 31
great video, the water from my engine comes out in flots. I have also changed the impeller and the gaskets.
@DaintreeJD
2 жыл бұрын
Thanks for the comment Michele. I wonder if your old impeller was damaged and some got stuck in the system before you got to take it out?
I was hoping to see the shift shaft separation procedure
@DaintreeJD
4 жыл бұрын
When i do this again I will update it so its included
@3videnc3
3 жыл бұрын
What's the shift shaft separation?
@leecannon6943
3 жыл бұрын
@@3videnc3 the point where the fixed shaft mounted inside the powerhead housing meets the long shaft that runs down to the gearbox
@davesmith2733
3 жыл бұрын
I always remove lower unit in reverse gear as can turn prop to line up splines easy on refit
@DaintreeJD
3 жыл бұрын
Thanks for the Tip Dave
No washer on top of impeller inside impeller housing? Looks like the kit comes with 2 plastic washers
@DaintreeJD
4 жыл бұрын
didn't get that in the vid, but yes there is one there, it took a bit of fiddling.
Do you have a part number for the water pump kit? I cant find the part number anywhere
@DaintreeJD
2 жыл бұрын
Hi there let me see if I can find it
@MrYz250fman
2 жыл бұрын
@@DaintreeJD thanks. Hope to hear back.
@DaintreeJD
2 жыл бұрын
@@MrYz250fman www.ebay.com.au/itm/Mercury-Mariner-Impeller-Water-Pump-Kit-for-40-50-60hp-Outboard-47-19453Q2-/194510265232?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=705-154756-20017-0
@DaintreeJD
2 жыл бұрын
Hope this helps
How did you attach garden hose?
@DaintreeJD
3 жыл бұрын
When I start it I use Muffs that cover the intake and feed the water in. Normal practice after taking the motor for a run.
Before dropping the lower end are you supposed to keep in neutral or forward gear
@DaintreeJD
Жыл бұрын
I had mine in neutral and it came out and went back easily. I know on other motors it must be in forward and even then I have found that I have had to jiggle between forward and neutral. This was not the case when I did it this time.
How do I correct the mistake of turning the shifter gear shaft
@DaintreeJD
4 жыл бұрын
Hi Al if I understand you right I have done that before and just slipped the prop back on temporarily and had someone turn it back and forth while I'm putting upward pressure on the leg to fit it back in
Washer is not in place
Should have marked the trim tab position before removing it.
@DaintreeJD
6 жыл бұрын
Good point for someone that isn't familiar with their outboard but I was ok and had it back in the right place.
Mine pisses out the side not back...
@DaintreeJD
2 жыл бұрын
Hey that's interesting, mine comes from the centre and kicks out to the starboard side.
@TeamTnA44
2 жыл бұрын
Mines a 30 though
@DaintreeJD
2 жыл бұрын
@@TeamTnA44 yeah that's prob why then hey.
It's a Key. Not a Key way. Don't lose the "key"
@gregktm
2 жыл бұрын
The key way is the slot on the impeller (as he said). The key is the metal piece that fits in the key way. You sir are incorrect.
@DaintreeJD
Жыл бұрын
Greg your right, it is the Key, unrehersed will sometimes do this.