Great video Mark, it's the perfect tutorial for anyone attempting this job and will make it very straight forward for them. Cracking job mate 👍👍👍

@MrMeltedwellies

4 жыл бұрын

Thanks Steve

Thanks. Just done my van door. Didn't need to remove rail, just clip out the plastic foot step and remove metal tray for easier access. Gave rail a good clean. New runners then just tilt into place. Note you have to slide the new one into the door support bracket. My runner wheels were knackered being by the sea with salt and sand. The door will support its own weight, just about.

@MrMeltedwellies

2 жыл бұрын

Nice work!

Great video. I'll be using it for reference when I replace the sliding door on my W639 tomorrow 👍😃😃😃

Brilliant thanks I'm doing all my baring s on both doors soon good to see how it just lifts out

Where the link for the product? Thanks

Thanks for the video! I made the same mistake with the locking mechanism, it’s easier to take out the whole rail, when you have removed the 4 torx screws, there is a 10mm bolt underneath of the car. Then you can easily take it out! Thx

@MrMeltedwellies

4 жыл бұрын

Thanks for watching

Thanks for sharing. Just about to do mine (on both sides!) so really helpful. 👍🏼

@Colwray1

3 жыл бұрын

If not done yet see my comment !

Getting those jobs done you’ve been putting off, by the looks of it, Mr D. Happy days.😷👍😷

@MrMeltedwellies

4 жыл бұрын

Thanks 👍 Funky hope your ok mate

@eyelidman09

4 жыл бұрын

All good here, Mark. Make the most of the glorious next few days, and look after yourself and your family, sir. 😷🌞🌞👍🇬🇧😷

Thank you for the video really handy

Great video. Thanks for doing this. Will be a massive help. Did you put the link in? I can't see it. Cheers

Thanks Mark for your mistaskes, help me to learn. lol

Hello, good video, where did you get the torx set from? Thanks Dave

Watched this first for ideas be if anyone trying this there is a far far far simple way to do this!!! simply pull up a little the plastic trim in the door footwell area. If you open the door fully if you look at the metal plate under the trim you will see the plate goes in a little towards the rear section! This is where you can remove the old one from and then if you get the new one and at an angle hook the two small top rollers in you need to give it a good jiggle to get it fully in place but it will go in, once in simple reattach to the door section 👍👍

@Colwray1

3 жыл бұрын

This video did help to start with thanks but after a good look you can avoid all of this 👍

@MrMeltedwellies

3 жыл бұрын

spot on 😆👍🍷

@Colwray1

3 жыл бұрын

Mark Davies but like I said this video was great simply to understand what’s there and could be involved but after looking I worked out the other way was easier .. only niggly bit is once you hook to two upper rollers .. get a flat piece of metal etc to make the gap up from the van into the roller slot so that as you wiggle it across the main roller jumps up into the track .. once in your laughing 👍👍

Great video, gives you a good idea before you do the job

Thanx allot for the video

Life saver! Thanks!!

@MrMeltedwellies

3 ай бұрын

Happy to help!

Tnx. Regards from fri man form Sweden.

@MrMeltedwellies

3 жыл бұрын

Thanks for watching! man from Sweden 👍🍷

Thank you!

@MrMeltedwellies

6 ай бұрын

You're welcome!

Thank you Perfect video

@MrMeltedwellies

11 ай бұрын

Thank you and thanks for watching

Thank you Mark.

@MrMeltedwellies

Жыл бұрын

You are very welcome

Well done with that fiddly job 🍷🍺👍

@MrMeltedwellies

4 жыл бұрын

Thanks Chris yep a little fiddly🔧🍷😂 👍

Top.

Thanks for making all those mistakes🤣👍 do it right do it twice👍

What is the socket size?

I'm just hoping nobody was trying to do what you do, pause and carry on... :)

If you reed this just do not follow this bloke(my mistake), he done plenty mistakes he admits, but honestly this video should be deleted as is misleading and could do it much quicker..

Too much rubbish talk!