This has been one of the most useful videos I’ve ever needed. Thanks for the video.

@BRIANPOOPMILLER

2 жыл бұрын

Literally everyone skipped this vehicle

Excellent explanation, Thank you for a great timing description for this car.

@SevSevy258

3 жыл бұрын

Very welcome!

Thank you for your informative video demonstration. Here I beg your permission to add a little information that it is the TDC (Top Dead Centre). Thanks again.

Good video. Easy to follow. Thanks.

Congratulations and thank you very much for the excellent tip and guidance! Success!

Thanks for the info and good video

thank you very much its a big help

Hi is complete correct i just done mine everything works perfect thanks for the video Sev Sevy

Great video, thanks for sharing your knowledge bro 👍🇬🇧

@SevSevy258

3 жыл бұрын

No problem 👍

Great video

Excellent explanation

awesome!

thanks for the video

Добро видео , колега ! :)

Спасибо четко и ясно

Thank you so much

Thank you so much!!!

VERY HELPFUL THANKS

Thanks so much that is very nice job

@SevSevy258

2 жыл бұрын

Thank you too!

is this the same on a 1996 c220 w202?

Would u please tell me what's the charge to repair a timing chain or guide on a mercedez 2001?

Would this be the same for a 1997 c230 Mercedes

So you didn’t change the chain and how many miles you have on the motor

hi will it be the same on an m111.951 c180 engine? thanks

Would this be the same for a 1997 c230 ? Plz help

Which is DTS point on crankshaft pulley please ?

Thz so much

@SevSevy258

6 жыл бұрын

ခ်စ္ ေဖေဖ welcome ;-)

Thanks

why is mine stuck on 30 cannot put it on 20 is it the chain ?

Instead of paint games you can put bolts of 4 to 5 cm length and 6 mm diameter in the holes by turning the wheel. That's the official way.....and after an click you can read the Timing on the scale ;-) Inlet 20 to 30°, outlet 25 to 35° after the 1st piston is on top (OT) of the scale....

@vvasilev1

Жыл бұрын

Не трябва ли да бъде точно 20° ?

@SevSevy258

3 ай бұрын

The "paint game" as you call it, it's for explanation purposes.

@MD-ro2of

3 ай бұрын

However, using a 4 mm pin for a 6 mm hole is senceless. The demonstration would be better to check the times correctly and not with paint. My 5 Cent.

Thank you so much for this video! I think my timing chain may be worn on my SLK230. Right now, I'm at 120k and the car is very slow/ sluggish. I'm also getting pretty low fuel economy and can hear a rattling/ tapping noise coming from inside the engine. Was replacing the chain a very difficult repair? Would you recommend it to others? I Would like to do it myself if possible. Thanks again for the video and the information!

@SevSevy258

8 жыл бұрын

Not a difficult job if you have mechanical skills. Ask a friend for help and remember to take lots of pictures in the process. You will need those when putting it back together.

@steftacular

8 жыл бұрын

+sevy mihnev Thanks so much for the advice! One more question for you, if you don't mind. Did you replace the cam and crank sprockets and rails as well as the chain? Or did you only replace the chain? Thanks!

@SevSevy258

8 жыл бұрын

It is always best to change everything, but it all depends on the condition of the parts in question. It is safe to assume that if the chain has stretched the other parts are probably worn as well if never changed before. 

@steftacular

8 жыл бұрын

+sevy mihnev Thanks, that makes sense! I will let you know how it goes!

Thanks for the inf

Акцент сразу заметен))) Раша)))

За двигател М111.944 валовете/веригата се заключва на около 27-28 градуса. Това добре ли е при положение, че веригата е нова, комплект. Или просто е разтегната, т.е. не е сменена.

i have some problems with my M111.961 engine. after i changed the chain tensioner, i did not do it correctly. so the wheel has sliped and the engine goes not stabile. how do i adjust the camshaft without dismount the chain itself ? thank you for your quick respons

@user-eh8vh3zp1m

6 жыл бұрын

Ты пробовал установить как он показывает?

is that correct for m111.941 engine ?? plz answer me

@SevSevy258

8 жыл бұрын

I believe so

How do I put the chain back on time , was replacing head gasket and went off on time won’t start now

@samurboi8007

3 ай бұрын

how did you not end up bending valves

Alguien entiende espanhol el tiempo está em 20 grados??

@afherrera44

3 жыл бұрын

Hola. Tengo la misma duda. Talvez pudiste confirmar si es a 20grados? O en la marca OT Punto muerto superior?

I did this for m111.974 and now I am getting cylinder 1-3 misfire.

@IamPaste

5 жыл бұрын

Sorry, my exhaust is off by quite a bit somehow, the intake is okay. I am going to fix it and see if it still operates in the same way.

Hello, I need HELP. I followed the video. Although I have the timing looking good at TDC when I turn to 20 degree the pins do not go into the holes Only at about 30 degree. The engine starts and runs rough. This is the second time I have pulled apart and checked it looks RT and it ran before I did the head gasket. What am I missing? Why would the holes not line correctly if I have the chain marks perfectly where they were? Thanks Jake

@SuperSw21

8 жыл бұрын

+Jake Dallmann the manual says 20-30 atdc.

@afherrera44

3 жыл бұрын

@@SuperSw21 Hi. Do you have Manual for this one please?

@afherrera44

3 жыл бұрын

Hi. Can you solve the problem?

@x8xPopCoRnx8x

Жыл бұрын

If you cant lock your camshafts when you turn the crank at 20 degree that means your engine is out of proper timing

@vvasilev1

10 ай бұрын

Моят също не мога да го заклключа на 20 градуса.Щифтовете влизат на 30. Това означава, че веригата е разтеглена ли? @@x8xPopCoRnx8x

Please I want to forward my automobile-engineer please I need someone to help me move forward please and I will be loyer to that person please

Combie'degre

🫡

selam beklerim

1 qoz

Нам тоже обяснилбы на родном своём русском языке Акцент бешенный сразу узнать что чел с ссср))))

@vitaliymorar18

3 жыл бұрын

Он с бывшей 16-той Республики но родной его язык Болгарский