Mercedes E63 AMG Front Wheel Bearing Replacement DIY (Mercedes W211 E55 AMG, C219 CLS63 AMG)
Автокөліктер мен көлік құралдары
►The wheel bearing is responsible for all of the rolling forces transmitted through the wheel. It's the piece that keeps the wheel rolling straight and true while bolted to the suspension, but they do have a service interval. Replacing your wheel bearing is a job you'll eventually need to do as a long-time owner, but it's simple enough to tackle in your driveway.
A wheel bearing will tell you when it goes bad. You'll hear a whirring or humming from the affected bearing before feeling it through the wheel at speed. There isn't a need for immediate repair once you begin to hear it, but the bearing will continue to deteriorate as you drive on it and will eventually cause much more serious damage.
Follow along as Mike Hidalgo, FCP Euro's Professional DIY'er tackles a front wheel bearing replacement on a W211 E63 AMG.
Index:
00:00 - Intro & Tools Needed
03:20 - Mercedes-Benz E63 AMG Front Wheel Removal
04:40 - Mercedes-Benz E63 AMG Front Brake Rotor & Caliper Removal
06:10 - Mercedes-Benz E63 AMG Wheel Bearing Cap Removal
06:25 - Mercedes-Benz E63 AMG Front Wheel Bearing Replacement
11:00 - Mercedes-Benz E63 AMG Wheel Bearing Cap Install
14:00 - Wrap-up
Shop the parts used in this video:
Mercedes-Benz E63 AMG Front Wheel Bearing Kit: www.fcpeuro.com/products/merc...
This video applies to the following vehicles:
Mercedes-Benz SL55 AMG
2003 Mercedes-Benz SL55 AMG
2004 Mercedes-Benz SL55 AMG
2005 Mercedes-Benz SL55 AMG
2006 Mercedes-Benz SL55 AMG
2007 Mercedes-Benz SL55 AMG
2008 Mercedes-Benz SL55 AMG
Mercedes-Benz SL600
2004 Mercedes-Benz SL600 Base
2005 Mercedes-Benz SL600 Base
2006 Mercedes-Benz SL600 Base
2007 Mercedes-Benz SL600 Base
2008 Mercedes-Benz SL600 Base
2009 Mercedes-Benz SL600 Base
Mercedes-Benz SL65 AMG
2005 Mercedes-Benz SL65 AMG Base
2006 Mercedes-Benz SL65 AMG Base
2007 Mercedes-Benz SL65 AMG Base
2008 Mercedes-Benz SL65 AMG Base
2009 Mercedes-Benz SL65 AMG Base
2011 Mercedes-Benz SL65 AMG Base
Mercedes-Benz CLS500
2006 Mercedes-Benz CLS500 Base
Mercedes-Benz CLS55 AMG
2006 Mercedes-Benz CLS55 AMG Base
Mercedes-Benz E350
2006 Mercedes-Benz E350 Base
2007 Mercedes-Benz E350 Base
2008 Mercedes-Benz E350 Base
2009 Mercedes-Benz E350 Base
2010 Mercedes-Benz E350 Base
2011 Mercedes-Benz E350 Base
2012 Mercedes-Benz E350 Base
2013 Mercedes-Benz E350 Base
2014 Mercedes-Benz E350 Base
2015 Mercedes-Benz E350 Base
2016 Mercedes-Benz E350 Base
Mercedes-Benz SL550
2007 Mercedes-Benz SL550
2008 Mercedes-Benz SL550
2009 Mercedes-Benz SL550
2011 Mercedes-Benz SL550
2012 Mercedes-Benz SL550
Mercedes-Benz CLS63 AMG
2007 Mercedes-Benz CLS63 AMG Base
2008 Mercedes-Benz CLS63 AMG Base
2009 Mercedes-Benz CLS63 AMG Base
2010 Mercedes-Benz CLS63 AMG Base
2011 Mercedes-Benz CLS63 AMG Base
2012 Mercedes-Benz CLS63 AMG Base
2013 Mercedes-Benz CLS63 AMG Base
Mercedes-Benz E63 AMG
2007 Mercedes-Benz E63 AMG Base
2008 Mercedes-Benz E63 AMG Base
2009 Mercedes-Benz E63 AMG Base
2010 Mercedes-Benz E63 AMG Base
2011 Mercedes-Benz E63 AMG Base
2012 Mercedes-Benz E63 AMG Base
2013 Mercedes-Benz E63 AMG Base
Mercedes-Benz E550
2007 Mercedes-Benz E550 Base
2008 Mercedes-Benz E550 Base
2009 Mercedes-Benz E550 Base
2010 Mercedes-Benz E550 Base
2011 Mercedes-Benz E550 Base
2012 Mercedes-Benz E550 Base
2013 Mercedes-Benz E550 Base
2014 Mercedes-Benz E550 Base
2015 Mercedes-Benz E550 Base
2016 Mercedes-Benz E550 Base
SUBSCRIBE: kzread.info?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/
Пікірлер: 43
Great and detailed video. Thank you and keep them coming!
Your video is perfect of how to replace wheelbearings, BUT you forgot to show how to replace the Wheelbearing seal. After replacing my bearings I had ABS/BAS/ESP light come on. After serious investigation, Firstly I did not know about the ABS Sensor/pulse Ring in the hub seal. I was told that you MUST be very careful with that ring, Firstly, you must NOT tap it in, you have to press it in, Secondly, you must NOT use a ferrous tool to press it in it has to be plastic/nylon/wood, also depth is important, if gap between sensor and ring is too large, then it won't pick it up, and it HAS to be level/straight. Those things are extremely important to show in your video. I had to purchase a complete kit again, just to get the new sensor ring.
@midwestwinefestival2862
2 ай бұрын
So your saying the reason why my ABS is going crazy is that my spring came out of the seal, so ABS will malfunction
@midwestwinefestival2862
2 ай бұрын
How can I email you for clarification
@vincentlonbird1806
Ай бұрын
My friend he didn't show the seal placement, because he replaced it with a new whole assembly. Meaning, hub, bearing and seal are already assembled
Great video!
Simple thank you so much. Gonna do this job myself now. Just need to order that one tool to measure that lock nut like you did. But ill be saving myself a few 100 bucks and all ill need after is an alignment.
When measuring the bearing play, one is supposed to pull and push the hub straight out, not wiggle it from side to side. In this video, there would be way too much play. Other than that it’s a decent summary of steps. Thanks.
@willsaund13
10 ай бұрын
He also said 1mm of play when the dial indicator clearly shows about 0.01mm of play. His instructions aren't very good
no one explains the dyi for the w211 models better then you guys this is a great very detailed video
Great video thank you!
@fcpeuro
Жыл бұрын
Glad you liked it! Appreciate you watching.
Great vid I was wondering why some of these bearings have a very thin inner ring that protects the rubber bearing on the inside. Is it a necessary component?
The correct torque for the nutbolts is 130nm
With the play is it normal for the wheel bearing to make a click noise when you pull it back and forth?
Same procedure for the w211 e55?
What is the tool and brand you used to measure the play? Thanks
Can you do the rear bearing for this car?
What tool do you recommend to do this measurement?
Do I need to touqe and use the digital too
1 mm Play ? or 0.01 mm play ?
@fcpeuro
Жыл бұрын
Hi Kowalski, that would be 0.01mm of play.
@fredericsangiorgi9507
10 ай бұрын
WIS: 0.01-0.02 mm (about 0.005”)
Please do tie rods next! Oh and engine mounts!!
@RothBeyondTheGrave
Жыл бұрын
No one on the internet mentions that you HAVE TO remove the headers to do mounts on a C207 chassis. Ask me how I know.....or you can drop the subframe & remove the engine mount brackets from the block. The top bolts are 100% impossible to remove otherwise. Took around 6 hours just to torque the top bolts down, 1/16 of a turn (at best) at a time. This was with exhaust & alternator removed. I hope you have a w211 & not a c207.
@OGYELLOW
Жыл бұрын
@@RothBeyondTheGrave w211!!! That sounds wild for you.
@RothBeyondTheGrave
Жыл бұрын
@@OGYELLOW honestly still can't believe it. I kept seeing w204, w212, w211, r171, etc vids of people just removing the heat shield & top bolt & thought it'd be the same. Amazing the tiny differences in clearance from similar chassis. Otherwise, straight forward job as well as tie rods.
Is see the list of cars this works on, is that for parts or is that for the method of changing the bearings? Is the principle the same for a w211 E55?
@fcpeuro
Жыл бұрын
Hi Nick, the process will remain the same for the most part; hardware sizes and locations may vary on the different models these bearings apply to.
So new bearing on old races?
Is a 2008 sl550 the same
Change it myself but now i got a nasty vibration everytime i brake ...
These things last a lifetime! Just clean'em repack'em, and adjust them properly. You're set for a long time.
You shouldn't use a rocking motion when setting the hub bearing, you should use a push and pull motion with both hands.
@fcpeuro
8 ай бұрын
Great Note!
I had a Mercedes Benz S500 (2005) the car had front wheel bearing very loose can,t take on freeway plus the rear airmatic pumps were leaking the pressure also the interior shifter linkage will break cost lots money the car had 140000 kms on it. My BMW 750 LI 2008 has 375000 kms still running great the only problem was stater on winter went it cost me 1200$ because the starter is under rear manifold had to drop down the engine, otherwise the best car . I have a Volvo V 70 (1999) the car has 360889KMS still running and my wife has a Cadillac STS V8 Northstar never had any issue the best GM product. thanks for uploading the repair videos.💞💞
My ABS system is giving me problems
Ok. Those grease caps....I've done every single wear item & common issue (besides esl & comand knob) on my C207 chassis, yet those grease caps were the ONLY thing that defeated me. The special tool that seats it flush all at once was the only successful method. The method used here got me absolutely no where in a time frame you wouldn't believe if I told you. I could have done S65 rod bearings faster. Wish I was joking.
Is it a 4 wheel drive or front wheel?
@fcpeuro
Жыл бұрын
Hi Therion, this W211 is a RWD model.
the sand does not lubricate
If you have no idea how to do correctly wheel bearing play do not... from manual: "Do not TWIST or TILT the wheel hub during measurement.Correct measurement is only possible by pulling and pushing PARALLEL to the wheel a axle."
The measurement is absolutly wrong !!!!!! your bearing play is more more more than it should be !!!! Your tool just slide not measure !!!!