Not taking too much away from you're video, but the m271 is aluminum head and aluminum block not cast iron

Thanks for posting! Now I know what my engine looks like on the inside.

So satisfying to watch, you made it look so easy!

@GetJobDoneofficial

3 жыл бұрын

The damage wasn't satisfactory 😄..thanks for great comments 👍

This is my car engine. Thanks for sharing.first time here.

very good , would love to see the reassembly of this engine as well

@GetJobDoneofficial

3 жыл бұрын

Thank you

Wow bent the rod!

Good job you make it easy to understand

@GetJobDoneofficial

3 жыл бұрын

Thanks, hope could help. Have you ripped your engine as well?

hello i have the same engine in a w211 and it consumes oil 1 liter in about 1500 km what could be the reason I have flushed the engine a few times with forte but no improvement

Great video brother u make it look soo easy

@GetJobDoneofficial

3 жыл бұрын

Thanks bro

I was working on replacing head gasket do to failed compression test and water in oil. Everything was going okay until I took off the cylinder head and two of the four pistons have a crescent shape missing (melted?) where the split in the piston ring is. I'm heart broken and considering the 05 c230 is far from perfect and the cost of new pistons I feel like my only choice is to scrap it at this point. I would consider jacking the car up and at least trying the repair if they did not cost so much. I also assume that it would be nessisary to take it to machine shop due to scoring of cylinder wall at the gap in piston ring.... yeah I guess its just scrap, this hurts. I love the video, thank you!

Hey brother, this is some great stuff on your channel. I hope that you can really answer my question. I just changed the balance shaft chain on this engine that goes around the other 3 sprockets but didn’t notice that they have indents on them as if they were timing marks. How do I go about orienting these 3 gears to their proper positions? Thank your time brother.

Thank you, great video. One thing though, please remove the electric screwdriver sounds next time when editing, it ruins the explanation you are making in the background.

Good video helped me out 👍

@GetJobDoneofficial

3 жыл бұрын

Thanks Michael, glad came helpful! Stay tuned brother!

Im working on one of these engines atm, any chance you know what position the balancer is supposed to be in relative to cylinder one? My cam sprockets have sheared teeth so its time for a new chain

@woczykijwedrowny3794

7 ай бұрын

I'm also looking for an answer to this question.

A cuantas libras torque lleva la bancada. ??? Y bielas ??

Nice to see my engine completly teardown. You arw right with the timing chain issue. I changed mine with 300333km on the clock (pre owner not known) because it started to show first symptoms of a loose chain. It was nice to see my engine without the cover on top

@harisyoung4110

Жыл бұрын

i just get a w204 mercedes with the same m271 engine.. the mileage now is 147k km, when do i need to replace those chain set ? now it still has no rattle sound..

@davishahn3101

Жыл бұрын

@@harisyoung4110 pop open the valve cover and do a visual inspection of the timing gears. If the gears are in bad shape you could replace it then. If it starts to rattle dont push the repair back, the timing chain can and will jump if damaged badly. If the chain jumps, you can throw away the engine because the pistons will get in contact of the valves, damaging it very badly and costly.

@xArchyv2

4 күн бұрын

@@davishahn3101I did my repair already and it still makes little rattle sounds. They replaced my cam adjusters, sprockets, cam magnets and chain tensioner. They said the chain and guide rails were fine. It does run better than before however it still makes noise at times. I told them my issue still persists but they said I have nothing to worry about. All I can do is hope it won’t break down. They offered to do a full break down like this video but yikes, I need my car. You have any suggestions on what it can be?

@davishahn3101

4 күн бұрын

@@xArchyv2 what Oil do you use? I used 5w40 in my m271.

@xArchyv2

4 күн бұрын

@@davishahn3101 I use 5w30 mobile1. I live in california too btw so different weather conditions, mostly hot.

Are the pistons forged?

Quien me puede decir que torque darle a las bielas y las bancadas de un 271

Cost of engine overhaul mine is using too much oil, think oil rings damaged and compression low pls advise.

what are the tightening torques for main bearing and rod bearings for mercedes benz C200 CGI W271.86 W204

This was hella clean how many miles did it have? the cam covers on my engine looked black

@GetJobDoneofficial

3 жыл бұрын

It was 20.000 miles

Great

How do you get the bolt out from under the guide pin and take off the lower timing cover?

@richardwhite6943

2 жыл бұрын

@@pipinxd7651 you pull a rubber plug from in front the pin in the timing cover, you then thread a long bolt with a nut and washer on it thru the hole into the pin, then tighten the nut and it will pull the pin out as it is just pressed in. Then the bolt comes right out. Also on Amazon there are several tool kits for this engine that remove the timing chain pins and holders for the cam shaft as well as the puller for the pin. But a bolt with a nut and washer work perfect and I can't remember the size but it is smaller like 5mm or 6mm and fine thread

I have the same car and I keep getting ESP error run flat indicator. I reset it and it comes up again intermittently while driving. do you know the cause of this?

@kylemcweeny878

3 жыл бұрын

Esp controls everything if u have an abs electric wire broken it will disable if u have a seed sensor go bad it will disable it. You need to put a scanner and find out what sensor is bad or wire is broken

Just wondering, is this a good engine to tune/modify/make higher horse power numbers?

@Kello7000

2 жыл бұрын

Unfortunately the kompressor variations of this engine do not have much of tuning potential. 1.8k m271 may get up to 40 hp gains with 62mm pulley and remap. On the other hand the turbo version known as m271evo can handle bit more tunning but close to 300hp with intercooler, filter, remap.

Good

Great video, would this be the same for my SLK 200 Kompressor, 184 CV, 2008, R171, M271.954 engine? Thanks.

@GetJobDoneofficial

3 жыл бұрын

Yes that's the same

@srp770

2 жыл бұрын

Should be the same, hovever the engine in the vid is M271.952 I beleive.

Do you know why these engines rattle at colt start although the timing chain and tensioner were new?

@Akluin30

4 ай бұрын

Time for oil pressure to build up

flood damage looks like lava inside when oil and water mixed lol

@GetJobDoneofficial

3 жыл бұрын

Definately, as destructive, as lava :)

Hi, just want to know if there can be oil leak shown in front of the engine where the camshaft aluminium covers are?

@mohammedrahmanrahman5024

3 жыл бұрын

if there a seal there anything can comes through a seal cause its only rubber.

@Daniel_D_King

3 жыл бұрын

Common fault in these engines. Camshaft magnets leak oil in to the wiring loom. You will need new magnets and seals and oil blocking pigtails. If its leaked a lot you will get oil in the lambda sensor plug, causing sensor failure, and if its not caught soon, oil will wick in to the ecu causing that to fail also

I am having a problem with my W203 M271 engine. The 1st spark plug has been stuck and all i replace are the remaining 3. How do I remove the stuck spark plug without damaging anything on the head. My cars performance gets affected as sometimes when I press down the accelerator the car has a rough idle and engine surging.

@klodiankurti3679

Жыл бұрын

Put some oil 2 days before removing it and try to remove it hot

On the idle stop when the is heavy traffic smoke comes out what could be reason.

@khumokwezimashapa2245

8 ай бұрын

From personal experience, I've found that it's low oil levels. When did you last check your oil?

Y el M282 es el mismo M271????

Throw a new piston and send it!

Is this a non interference engine?

What year was the c180 from?

@GetJobDoneofficial

3 жыл бұрын

This was in w204 range.

@catalinbanici3357

3 жыл бұрын

Ok. Thank you! I really thought that Mercedes fixed the timing issues with the 4th gen but it seems not. Still the same with m271 cgi engine?

that crank shaft is cheap i would change it if was gonna rebuild it up.

@GetJobDoneofficial

3 жыл бұрын

I think someone will any way!

Don't worry about the conrod bent like a banana. How could you not notice that? And you wonder how the crankshaft journal got damaged 🙄

Balance shaft? lol! That’s Balenciaga my friend!

Big end, small end, cast iron, cast aluminium, all the same. Anyway, why was the conrod bend ? Hydrolock, obviously but why ? Head gasket or maybe a cracked cyl head, that you're unable to see. I would do a bit more investigation before re-assembling. Cranckshaft ? At least have it checked, grinded and see if you can save it with oversized bearings. If in doubt, replace it.

How reliable is this m271 engine?

@GetJobDoneofficial

3 жыл бұрын

Maintained very reliable, therere are many versions of them.

@kylemcweeny878

3 жыл бұрын

I beat the crap out of mine everyday for 5 years still have still beating it up

@slowestamg

3 жыл бұрын

@@kylemcweeny878 I have a 2015 C250 Coupe. How many fuel pumps and engine mounts have you gone through? I have gone through 3 fuel pumps, 2 sets of engine mounts and a power steering pump (along with other minor repairs and regular maintenance items).. I only have 60,472 miles on it right now but they are probably some of the hardest miles any m271 will ever have on it lol. Asking out of curiosity for maintenance comparison

@kylemcweeny878

3 жыл бұрын

@@slowestamg none of those lol... just regular maintenance... the screen is starting to get messed up (edges color fading) but I think thsts because my car sees a ton of moisture (windshield wasn't water tight for like a year. And other leaks in places I haven't found.) Wheel speed sensor went out last weekend left me stranded 😫 fixed for 70 bucks. The pcv hose broke when I first bought it but I replaced it with a rubber hose from auto parts store for like 10 bucks... oh and the passenger inside door handle/armrest (leather, holds window switch) that fell off on my wife today actually. But I've left windows open in the rain a bunch of times so that probably aided to that 😅 but seriously I have oversized wheels 20's and I slammed it to the floor.. literally can't fit a low profile jack without driving up on wood. Stiff coilovers, rubber band skinny tires... the boots ripped on the cv joints/axels like the first week I lowered it.. never fixed that ...that was a year ago ...still driving it like a mad man ...still she goes strong! Steering wheel is peeling seats are ripping plastic buttons becoming unreadable but mechanical she's doing great.. very impressed actually... I changed the alternator 700 but that's because I had the oil feed line leaking oil onto it... forgot to mention that oil line lol and the banjo bolt I did it in the process because it would smoke on start up but now its mint! Whew what an essay lol

Looks easy with the right tools, but hey get down in the garage and see how much sweat pours down .

Removed that silly bolt 🤪

@steve_marais3510

2 жыл бұрын

I would love to know how

So many wrong steps just disarming …

that crank just polish it a little and back in!!!

Is this a interference motor?

@rafaelroa5638

Жыл бұрын

yes