You can change 1 at a time to prevent mixups. Leave the coils attached because those clips break easy. A magnetic flexing sparkplug socket is like $15 and worth it. Power tools are fast, but take your time with manual on your own vehicle because screwing up a sparkplug thread can result in big$$$ fixing it.

Good vid... and I liked it when you air blew the dust and debris before removing coils

Awesome step by step breakdown!

nice video!!.. straight to the point👍.. no unnecessary info

A lot of great advice! The magnet tip really helped. Great demonstration. Thank you!

@JimmysAutoClinic

Жыл бұрын

Thank you for the compliments :-)

I watched this video three times and I'm so glad I stuck around the third time for the outtakes. 😂 This was my first time changing my own plugs and it was a success! thank you for this great tutorial.

@JimmysAutoClinic

2 жыл бұрын

Hey Drew thank you for watching. I'm glad I could help. Of course please don't forget to hit that subscribe button. Hopefully I'll have some more Mazda videos for you soon.

@bicboss4486

Жыл бұрын

how much did u save from the dealership

Excellent video my 2014 is due for spark plugs soon!

@JimmysAutoClinic

3 жыл бұрын

Awesome I'm glad you liked the video. If you haven't already please consider subscribing to help me out. 🙂🙃😉

Next video; rotary engine swap on a Mazda 3. Give the people what they want Jimmy! 😂

@JimmysAutoClinic

3 жыл бұрын

Maybe one day LOL

Great video sir!just made me realize that on my same mazda I have a solid oil spill/leak on the generator...you have any ideas what causes it? It kinda makes me nervous. Wish to hear you from! Thanks

@JimmysAutoClinic

2 жыл бұрын

I'm not sure what would cause the oil leak. The best thing to do would be to wash it off and then start the vehicle up to see where it might be leaking from. I have a video on how to power wash an engine bay so that you don't make any costly mistakes. Check that video out before you power wash your engine bay and don't forget to hit that subscribe button. I hope this helps you.

@szabodaniel3001

2 жыл бұрын

@@JimmysAutoClinic thanks for the answer, going to check it and hope for the best!

Is it better to replace the stock with ngk iridium sp for mazda 3 2018? Is there a significant difference in performance and gas consumption?

@JimmysAutoClinic

2 жыл бұрын

Generally in most cases you won't see a noticeable increase in performance in terms of horsepower. Over time with long trips you may see a slight increase in fuel mileage. But that mainly has to do with the plugs being new, of course depending on how old your original plugs are also. Most newer cars come with a platinum plugs so I'm assuming that yours probably are. NGK is a great company so whatever plug is recommended by them should work really well. Also check the cost of the stock replacement plug. Sometimes the dealership is actually cheaper than aftermarket replacement. Good luck 👍

@HansLotap

2 жыл бұрын

@@JimmysAutoClinic thank you so much.

Thanks for the video my 2014 mazda 3 just started having less power but no check engine light was on so I changed all the spark plugs and noticed the problem was stil there still with no check engine light. So the next day I went and bought 4 new coil packs changed them all and then the problem was still there it actually got worse and the check engine light came on.

@MrChivamex14

2 жыл бұрын

someone help lol

@JimmysAutoClinic

2 жыл бұрын

Hey Mario, the best advice is to put back the stock spark plugs and coils. Then run the car with a scanner that will tell you live data, generally when you have a lack of power it could be related to a number of things depending on mileage and maintenance. I would need a bit more information to put you on the right path but I would say check the live data to see what your fuel trim numbers are. Also see what your oxygen sensors are doing. I would also look at the air filter if it's never been changed of course this all depends on mileage. If you're close to the Toronto area the easiest thing would be just to come by. I hope this helps you

What model TESLA is this ?

link to that badass magnet thing you have? thanks for the vid

@JimmysAutoClinic

Жыл бұрын

Hey Kalen can you link the time in the video that I used the tool and I will post the part number for you or a link if it's available on amazon.

"WTF Kevin" LOOL

I changed the spark and coils on . 2012 mazda 3, but I still get missed fire on 3rd cylinder. What can be other issues. You advice will be highly appreciated

@kieranmilton2276

Жыл бұрын

Have you checked the fuel filter & fuel hose? They could be clogged

@JimmysAutoClinic

Жыл бұрын

Hi, if you change the ignition portion the first thing I would do is switch the coil or spark plug with any other cylinder that is good and see if the problem follows. If it does either spark plug or coil is defective. If it doesn't you may have an issue with many other possible things. The first thing to do would be to check compression, the second thing to do would be to do a leak down test if compression is low. Or if compression is fine it's still a good idea to do a leak down test. If all of those tests check out the next thing to do would be to check out the fuel delivery system. It may just be a bad or going bad injector. It could be wiring to the injector or coil possibly. But start with the basics by doing a coil Swap and then checking compression.

@JimmysAutoClinic

Жыл бұрын

Hey, good suggestion but I don't think that would be the next step. Check out my reply if you'd like to find out more. Thanks for trying to help out.

I did spark plug replacement on all then changed #2 coil pack and I’m still having misfire in cylinder #2 I even went to the extent to clean the throttle body 😢idk what else to do

@JimmysAutoClinic

Жыл бұрын

Hey, unfortunately it sounds like you have some real issues that may need to be diagnosed by a mechanic. If you're in the Toronto area I wouldn't mind helping you out. What you can do to take a look at the engines health is do a compression test or what is called a leak down test. Those two tests will tell you what's going on with your engine. If everything looks okay there I would look at possibly a bad injector if it's just the one cylinder that consistently misfires. I would also swap the coil with a known good coil from another cylinder because even brand new aftermarket coils have failed in the past on me. I hope this helps if you have any other questions feel free to reach out. Thank you for watching.

Nice vid. Why didn't you use ant-seize on the new plugs ?

@JimmysAutoClinic

Жыл бұрын

Hey jeffrey, it is not recommended to use anti-seize on spark plugs. It really depends on the type of spark plug and head material. There are very few instances where it is a good thing. Whenever you have a steel spark plug going into an aluminum head it's not generally a good idea. It also depends on the type of anti-seize and the duration of the plug is supposed to be used for. In short there are many different factors that determine whether you should or shouldn't and it is almost always better not to have anti-seize in that specific area.

@richieapodaca4100

Ай бұрын

@@JimmysAutoClinic correct..NGK Laser Iridium comes with anti seize coating

Why would you not use a torque wrench if you have it to tighten them in after the power tool if you have one? Seems like an unnecessary step that could cause overtorquing the spark plugs (even if that's not likely to cause any major issues). Just a minor point.. otherwise excellent video!

@JimmysAutoClinic

2 жыл бұрын

Thanks for the comment Tim. So the general process for doing spark plugs and the reason why I use a power tool is only to run down the spark plug because a lot of newer plugs are quite long. Essentially the power tool acts as a speed handle would. But in no way shape or form should you ever use a power tool to tighten up a spark plug. You should always use a torque wrench to torque the spark plug to the correct tightness required. Power tools like an air ratchet or impact driver are quite violent so if you try to apply torque you can easily break the spark plug which would be a bad day. I hope this answer helps you. Of course don't forget to hit that subscribe button if you haven't already.

What is the torque specs for the sparkplug?

@JimmysAutoClinic

Жыл бұрын

I think I mentioned the torque in the comments somewhere or in the video.

podrias decir el codigo de las bujias que utiliza?

@JimmysAutoClinic

2 жыл бұрын

Sorry I don't understand Spanish

@pipediaz6631

2 жыл бұрын

@@JimmysAutoClinic Could you tell the code of the spark plugs it uses?

@JimmysAutoClinic

2 жыл бұрын

Unfortunately my friend I do not know that information. The best thing you can do would be to call your local dealership with your VIN number and they'll be able to give you the appropriate spark plug needed for your vehicle. Please Subscribe if you haven't already. Thank you

How long they need to be change the spark plug?

@JimmysAutoClinic

Жыл бұрын

I'm not sure what the interval is my friend.

@jeriwolfcr7838

Жыл бұрын

75000 miles recommended

what is the part number of the plug?

@JimmysAutoClinic

Жыл бұрын

Unfortunately my friend I don't remember what the spark plug part number, the best thing to do would be to get the part number off of the spark plug that is in your engine if you know it is the original plug. If not I would suggest taking your Vin number to your local Mazda dealership parts department where they will be able to tell you what the exact part number is that is needed. You can then take that part number and cross-reference it to get the correct plug with any parts store. Hope that helps don't forget to hit that subscribe button.

I read that the torque spec should be 10 - 14 Nm , wouldn't that be roughly 7 - 10 ft lbs? You tightened them at 20 ft lbs, which over double .

@JimmysAutoClinic

Жыл бұрын

To be honest I can't remember what the torque spec is. But as long as you don't go too tight you'll be fine. You can make those decisions based on the length of the spark plugs threaded portion as well as the type of material the head is. 20 foot pounds Maybe tight in comparison to what the manufacturer says but I haven't had any issues doing this through the years.

DO NOT tighten your spark plugs with a battery drill/impact gun as shown in this video! It can damage the threading on the cylinder head, the spark plug is steel while the cylinder head is aluminum, screwing it in with your bare hand can avoid cross threading which can damage the aluminum threading easy, so its recommended that u screw and tighten your spark plugs with a rachet

What plug

@JimmysAutoClinic

Жыл бұрын

Sorry my friend, can you be more specific?

@golightly209

Жыл бұрын

2016 Mazda 3 2.0 skyactive hatchback spark plugs. Dealer not answering phone.

@JimmysAutoClinic

Жыл бұрын

This is the part number that I got offline ILKAR7L1, it's an NGK part number. But it is best to check with the dealership to see what is appropriate for your VIN number.

If you don't need to disconnect the connectors for changing spark plugs, why did you? Makes no sense...

@JimmysAutoClinic

Жыл бұрын

Hey bobby. I don't remember exactly what I said but if you don't need to disconnect the connectors to change the spark plugs that doesn't mean that you can't. In my case I always take the ignition coils off inspect them clean them and put them back into the car which is much easier to do with the wiring harness disconnected. Hopefully that answers your question. Thanks for watching don't forget to hit that subscribe button.

No antisieze or gap mentions tho.

@JimmysAutoClinic

2 жыл бұрын

Hey TJ Eclipse, antiseize is generally not needed. If you are going to use it you can use copper antiseize. In regards to the Gap these plugs were from Mazda, I did check the gap to make sure that they were all the same across the four. Unfortunately I don't remember off the top of my head I will look it up for you.

@JimmysAutoClinic

2 жыл бұрын

Gap Used Plug 1.05 - 1.40mm New Plug 1.05 - 1.15mm I hope this helps you. I have also updated the description with the same information. Please don't forget to subscribe if you haven't already. Thank you :-)

@dickieradd

2 жыл бұрын

Shouldn't use antiseize with aluminum, and the gap from NGK will be factory done. He did everything right man..

12-14 ft/lbs.. guys don't use power tools for this..

@JimmysAutoClinic

11 ай бұрын

I agree if you don't know how to use power tools you shouldn't be using them. The same also applies to hand tools or common sense.