Why doesn't anyone do a video on how to change the grease?

@timkessler4894

2 жыл бұрын

What grease the wringer or the power unit? The power unit requires a special tool to drain the old lube out which I don't have but I will keep looking. Tim

Hello Mr Tim thank you for the Video's. I wanted to know where do you find your parts for your wringer washer??

@timkessler4894

Жыл бұрын

I use either eBay or Cottage Craft Works they are great for finding what you need. Tim

Tim, I was wondering if one can fix a sprung centering spring under the medallion type disc with the center screw on the top wringer part?. I tried fixing it with no luck. Thanks

@timkessler4894

2 жыл бұрын

I've never had one brake before so I'm not sure. I wonder what broke it is just a coiled piece of wire. Sorry. Tim

Hey Tim, where did you get your soft roller?

@timkessler4894

11 ай бұрын

I looked for it on eBay and there was a seller who had them. Tim

My center plate is leaking. That’s my project for the weekend. I have some plumbers putty in my toolbox and I’m hoping that’s all it needs.

@timkessler4894

2 жыл бұрын

I hope that will fix it. I hope it's not leaking into the power unit. Because it will be a job to replace it. Good luck let me know. That's why it is a good idea to paint it it is only cast iron. Tim

@OwnYourOwnBus101

9 ай бұрын

I painted the center plate like you said. It stopped the pinhole leaks too. It was a great low cost solution!

What paint did you use on the center plate?

@timkessler4894

Жыл бұрын

I used a spray paint for appliances the center plate needs the protection it can get because I have seen what the plate looks like when it's gone and they are hard to find. Tim😃

I need to find the gear& parts for the wringerhead that go onto the tower drive shaft.

@timkessler4894

Жыл бұрын

I don't know where to get the parts for the wringer head, but you can try Cottage Craft Works. But if you can't find the parts you may need to get a new wringer complete that's all I can suggest. Let me know. Tim

How do you adjust the pressure on the rollers to make it press water out better?

@timkessler4894

2 жыл бұрын

The manual says the only way to get more pressure on the rolls is to use oversized bearing hangers and I tightened the tension springs all the way. Let me know if you need anything else. Tim😃

@timkessler my wringer doesn't release or "pop up" when I hit the release bar.. could spring be broke or unhooked?

@timkessler4894

Жыл бұрын

Yes that is a good possibility. There is a centering spring for the release bar for some reason it is not releasing it is not retracting the tension levers like it should there maybe some other issue. Let me know if you are still having issues. Tim😐

@colonmills6075

Жыл бұрын

@@timkessler4894 I got it oiled and clean, and it started working.. now I have to replace the hose from washer tub to the pump .. any tips?

@timkessler4894

Жыл бұрын

Cottage Craft Works should have the hose you need or ebay if you notice that hose is different so you shouldn't have to much trouble they should have it. Let me know. Tim🙂

@timkessler4894

Жыл бұрын

@@colonmills6075 When I took my wringer cap apart I greased all the moving parts in the working tension reset part it will lub it much longer. Tim 😃

@colonmills6075

Жыл бұрын

@@timkessler4894 I've got everything working but the pump .. guess will have to take it apart next

The grease in my El2 is like Alaskan Molasses! What kind of grease did you use for the wringer cap? Did you need to replace the thin seal that goes in there too? Also, what kind of paint did you use on the center plate?

@timkessler4894

2 жыл бұрын

I used a white enamel spray paint. I covered the agitator shaft with aluminum foil. I used a high quality gear grease for the wringer head the grease in mine was like molasses to and the rubber ring seal was fine. Glad to hear you are tackling the machine. Let me know if I can help you further.😀😀 Tim.

@OwnYourOwnBus101

2 жыл бұрын

@@timkessler4894 I got a new belt for it yesterday. Same size as the last one, yet it was too small. My tub to pump hose was dry rotted so I got some silicone tape from the auto parts store and wrapped it up tight. That should do it. I'd like an original drain hose and drain attachment (instead of the straight replacement hose I had to use) so I'll try Cottage Craft on Ebay. I'll also look for that centering spring in the wringer cap today. As you said before, maybe that's why the cap doesn't lock down. Thanks for the tips!

@timkessler4894

2 жыл бұрын

What was the condition of the gears in the wringer head? We're the gears in good condition and the camshoes if there are fine the roller should turn. If you need a new belt go to Tractor supply those are farm and ranch supplies great quality. It takes 1pound of grease for the wringer head.😀 Tim.

@timkessler4894

2 жыл бұрын

Cottage Craft Works has the centering springs they have a good selection of parts available maybe they will have the hose you need to. Does it have the sediment filter if it has a pump they have those too.😀 Tim.

@OwnYourOwnBus101

2 жыл бұрын

@@timkessler4894 I took the top roller out just now to have a closer look at the mechanism. It seems to lock in place just fine without the roller. Once I put it back, same problem. The bottom roller is hard as a rock. The top roller is almost as hard. I wonder if this could be the problem?

How do you get the spring in without breaking it??

@kimberleethuem1363

3 жыл бұрын

In the wringer top

@timkessler4894

3 жыл бұрын

I guess I don't understand the question what spring The tension springs on a Maytag are under the wringer frame the wringer cap only slides on top of the cap for tension bolts.Tim

@kimberleethuem1363

3 жыл бұрын

@@timkessler4894 in trying to get the centering spring on, when we got it on but when we turned the tension release bar, it snapped.

@timkessler4894

3 жыл бұрын

@@kimberleethuem1363 Please refer to my Maytag manual video it shows how to put on the centering spring it is tricky you have to make sure that the release bar in in the release position and then place the spring hope this helps you if you are still having trouble please let me know I can post that part of the manual on a video to show you can't wait to see your machine.Tim

@kimberleethuem1363

3 жыл бұрын

@@timkessler4894 I don't know how to post a picture to you, I'm afraid. Since we broke this spring, we have to wait until the replacement arrives. We think we've figured it out but a video would be very helpful! Other than the wringer, the machine works great. I would like to get a manual like yours to do maintenance. Where did you get it? I do need to refurbish the bottom outside because it's rusty.