Mastering Belt Conveyor Motor Selection and Calculation: Ultimate Guide
In this Video you will lean, how to make perfect selection of motor and gearbox for belt conveyor, by in depth calculation of motor power, motor torque, motor speed and moment of inertia of complete belt conveyor system.
Additionally you will lean, importance of motor starting torque and acceleration time for belt conveyor,
Top of that we have also covered VFD calculation for belt conveyor. In following chapters
Chapters
0:00 What we will lean.
0:23 Required input for motor selection
1:07 Selection calculation basis
2:44 Requirement example
3:27 Conveyor belt selection
5:26 Belt conveyor speed calculation
6:34 Belt conveyor power calculation
9:02 Belt conveyor linear speed to RPM
10:35 Mistake in belt conveyor power calculation
12:13 Motor starting torque calculation.
14:43 Belt conveyor moment of inertia calculation
16:46 Motor acceleration time calculation
18:01 Belt conveyor motor selection and number of motor pole
21:05 Belt conveyor gearbox selection
22:20 Belt conveyor motor VFD calculation
Motor selection data sheet and catalog: drive.google.com/drive/folder...
Belt conveyor design complete playlist: • Machine Design Series ...
#conveyor #beltconveyor
#Machinedesign #Mechanicalengineering #masterclass #mastermechanicaldesign
Afflicted links:
📌 RECOMMENDED BOOKS FOR DESIGN ENGINEER 👌
1. Strength of material (Yellow book): amzn.to/3pHQ0S5
2. Industrial design: amzn.to/3qSoxNx
3. Machine design: amzn.to/3NJBbYd
4. Theory of machine: amzn.to/3Jy3J4i
5. Concept of Physics: amzn.to/3NNWjww
6. GD&T: amzn.to/3NNq28V
📌 THE GEAR I USE 💻
1. LAPTOP FOR DESIGN: amzn.to/3pr0h4I
2. CAMERA (Mobile phone) : amzn.to/3Jz3ypI
3. SSD Drive: amzn.to/3pncgAp
4. MIC: amzn.to/3NMNSBt
Keywords:
conveyor belt power calculation
belt conveyor power calculation
conveyor belt motor power calculation
how to calculate motor power for conveyor belt
how to find motor power for belt conveyor
motor selection for conveyor belt
Belt conveyor motor selection calculation
Berechnung der Förderbandleistung
конструкция машины
Maschinendesign
Thiết kế máy móc
diseno de la maquina
projeto de máquina
Conception de la machine
تصميم آلة
機械設計
Пікірлер: 262
Thank you sharing the knowledge
This is a very good video for the conveyor design, we need more video like this, thanks sir
Very good video , thanks Master
You are great sir ❤
Awesome explanation, very complete. Thanks a lot!! Keep going with more videos, Bro!!
@mastermechanicaldesign
2 ай бұрын
Glad you liked it!
Omg..thank you sir..i was finding these calculations but you made very easy….thank you
@mastermechanicaldesign
10 ай бұрын
Glad to hear that 😊😊
This video is for my level technical expertise. Thanks ❤❤❤
@mastermechanicaldesign
8 ай бұрын
I'm glad 😊
Usefull video...thank you bro
@mastermechanicaldesign
11 ай бұрын
You welcome sivasugandan 😊
Mostly valuable information sir thankyou.
@mastermechanicaldesign
5 ай бұрын
Most welcome
It was so amazing explanation 👏 Thank you bhai
@mastermechanicaldesign
7 ай бұрын
Most welcome 😊
THANK YOU SO MUCH SIR, FOR SHARING KNOWLEDGE....
@mastermechanicaldesign
8 күн бұрын
You are most welcome
you are awesome man
@mastermechanicaldesign
8 ай бұрын
You too. Thank you 😊
Great sir make such videos regards mechanical design selection, calculation, Power train, gear ,shaft , pulley,motor selection etc
@mastermechanicaldesign
10 ай бұрын
Sure 😊, thank you so
Beautiful ❤
@mastermechanicaldesign
11 ай бұрын
Thank you! 😊
me gusto la informacion que ofreciste
@mastermechanicaldesign
6 ай бұрын
De nada ❤️
Dear sir, Very very classical tutorial...
@mastermechanicaldesign
6 ай бұрын
Thank you so much rahul 😊
Well Done Sir, As An Engineer I can say that your Channel will help most of Person who belongs to Machine Design field 👍
@mastermechanicaldesign
2 ай бұрын
I'm so glad 😊
Great sir...
@mastermechanicaldesign
11 ай бұрын
I'm glad 😊
Thanks 🙏
@mastermechanicaldesign
10 ай бұрын
U welcome
Really video is great please make more such videos if possible please make video for designing of special purpose machine
Awsome video sir ❤❤
@mastermechanicaldesign
10 ай бұрын
Thank you jay 😊😊
My sincere congrats for the detailed explanation on the motor selection; it's reassuring to find that there still are some decent material not solely based on unbiased simplifications! I have a question tough, would you mind helping me out if possible? If the conevyor belt is designed to be pre-tensioned and mounted on top of rollers, in order for an object to move, there must be no slipping between the roller and the belt, right? Hence, the friction is the force pushing the objects forward on the belt and is not a resisting force, meaning there is no pulling force, likewise you mentioned at 11:02. In that case, the only torque is due to the inertia, correct? Does that mean that, when the object has achieved its final velocity, all power given by the motor is spent by friction on bearing, gears and others? Thanks in advance for the video, have a nice day!
@mastermechanicaldesign
2 ай бұрын
Thanks Joao Garcia, Lets discus! Point 1: There must be no slipping between the roller and belt, right? - Yes, it would be better if it is not slippery, but practically zero slip is not possible as you know. Point 2: Friction pushing the object forward on the belt and is not a resisting force- Yes absolutely right. Your last point, all power given by the motor is spend by friction on bearing, gears and other after reaching final velocity- This is complicate, yes this is 100% true that motor required torque will decrease after reaching final velocity means at zero acceleration. but as we are moving a belt, so there will be always a belt rolling friction, (thick belt means more rolling fiction), also there is not only roller MOI, but there is also transferring object and belt itself MOI which always being influce by gravity, as you said, motor is spending by friction on bearing, gears and others, so this term other is going to always much larger as compare to bearing friction.
@joaogarcia9855
2 ай бұрын
@@mastermechanicaldesign Thanks for the response, it makes sense: wile it's true there must be no slip and hence the friction is not a dissipative force at first, it's hard to guarantee no slip, which is hence the dissapative force when the final velocity is achieved. Therefore, while it's not correct stating there is not dissipative friction, it's also not correct stating the pulling dissipative force is F_pull = (load_weight) * friction_coef. , right? Unless we consider "friction_coef." beign much smaller than the actual kinematic friction coefficient. For rxample, rather than adopting 0.2, we take 0,05. Do you thing that's a reasonable approach? The losses in bearings, gears and other I'll consider by using their efficiencies as 99% or 98%, for example. Once more, thanks for the responses, for the video and for the commitment on the subject!
@mastermechanicaldesign
2 ай бұрын
Let's think in this way, 1. To move the belt, a strong frictional grip between rollers and belt is required, stronger the frictional griper of roller will give better will be result in terms of slip resistance, (So, sometimes we do knurl over rollers surface for better grip) in other word, frictional force between roller and belt should be more than frictional force of belt with conveyor's other parts (belt bottom support) with the load over belt. means, Friction force between roller and belt (depends on amount of belt tension, roller contact arc with belt and static co-efficient for friction between rollers and belt) should be grater then frictional force of belt (loaded with material) and belt support plate, 2. At starting frictional force of belt (loaded with material) and belt support plate will be high, and once belt start moving static co-efficient of frication will decrease to kinematic co-efficient friction. 3. Now, motor capacity should be cable to accelerate the belt from its static friction because we started the motor at zero velocity. 4. Friction between roller and belt is different than friction between belt support and belt, our aim should be increasing the friction between roller and belt for no slip. whereas our aim should be drecrece the friction between belt and belt suport, for easy pulling the belt, 5. Now, bearing friction is something that we should not consider in any calculation, you can consider as zero friction (in general) 6. So, for motor selection, these are following load you should consider. A. Frictional pull force between belt with load and belt support, B. Belt rolling friction (or you can say belt rolling resistance or belt drag over the rollers) -Which is actually difficult to calculate. C. MOI of all the rollers, gear box, motor and the load over the belt.
@joaogarcia9855
2 ай бұрын
@@mastermechanicaldesign Awesome! It makes sense for me now. I don’t know how to thank you enough for the time and response! Once more, congrats for the content and commitment! You’ve got a subscriber for sure :)
Thanks for giving calculations for Conveyor Belt Power.. I want to suggest that kindly make a video about Selection of Power Transmission Belt Drive or No. of belt.. in which Counter pulley System.
@mastermechanicaldesign
11 ай бұрын
Noted, I would be better to do this within a transmission design series
thanking u sir u are really good and excellent knowledge in this topic i understtod and learned so many points sir explanation is very clear and awesome 👌💯🙏
@mastermechanicaldesign
6 күн бұрын
You are most welcome
Excellent tutorial, created a spreadsheet from this for future conveyor designs. What additional do we add if the conveyor is inclined?
@mastermechanicaldesign
7 ай бұрын
Thank you 😊😊 Mainly Pulling force for motor, will increase, Cosine component of frictional force (Vector physics) will be added in total pulling force. 👍 I will make detail video on include conveyor calculation also, very soon.
Nice information
@mastermechanicaldesign
5 ай бұрын
Thanks
Amazing
@mastermechanicaldesign
4 ай бұрын
You are amazing
Thanks for very good explanation. Please make video for the selection of gearbox for indexing table application
@mastermechanicaldesign
2 ай бұрын
Yes sure!! noted
Good information and much appreciated your efforts but kindly recheck the considerations for calculations as they seem little offset from actuals, as there is no much difference for the motor KW but when it comes to judge what can be done with other parameters to decide some intermittent operations that you get across while introducing other process based on selecting rpm’s and force flow process, might mislead to wrong assumptions though. All the way nicely explained
@mastermechanicaldesign
9 ай бұрын
Hi Bharathrm, Thank you so much. yes, there is little calculations typing errors with example. But concept and formulas are right. Just bear with me. mistyping will eliminate completely with time. trying to build a cross check community.
गुरु बिन मंगल फेरते गुरु बिन करते दान गुरु बिन सब निष्फल गया, वाचो वेद पुराण
Please make a video of shaft deaign, and also give the information about allowable shear tensile streess and strength and allowable bending moment and fatigue failure and what will be the safe value from protecting above point
@mastermechanicaldesign
5 ай бұрын
Noted Atish,
thanks master jii
@mastermechanicaldesign
7 күн бұрын
So nice of you
Very nice explanation sir. 1) What is the power loss in gear box? 2) What is the factor of safety consider the moment of inertia of the belt load?
@mastermechanicaldesign
4 ай бұрын
1. Gearbox power loss - consider gearbox efficiency 90% for helical worm gearboxes 2. FOS for MOI- If you are considering every component MOI (belt, load, rollers) then you don't need to consider any extra FOS.
Please make a video on power roller conveyor design
Kindly Make a video on calculation of axial and radial load for bearing selection.
@mastermechanicaldesign
11 ай бұрын
Sure dhiraj, Complete bearing series is planned.
Best
please make video on how to design slat conveyor.
Hello. Thank you for the video. Where did you get the acceleration times from? "0-2 seconds for 1/5 hp" etc.
@mastermechanicaldesign
3 ай бұрын
This is actually a range (a rough estimation) because acceleration depends on how much the initial load is over the motor. I have taken this from a research paper from ABB laboratory
Very good and informative videos bro ... thankyou.. i need one clarification, how do select dia of the roller? Is there any standards? And torque based on MOI is it finding for all the drives?..
@mastermechanicaldesign
7 ай бұрын
There is no such standard, but yes roller diameter should be sufficient to roll the belt properly. Means if we take a thick belt then we should consider a large diameter. Also we should try to keep the roller diameter minimum to reduce the MOI Third yes strength but it depends on length and tension on the roller (no significant concern)
@sampathcm5054
7 ай бұрын
Thankyou ❤
Hi Ayush,waiting for Powered roller chain conveyor calculation video
@mastermechanicaldesign
6 ай бұрын
It will take some time. First we will complete bearings sizing and calculation parts
For some calculated power for an mechanical application, can we selecte AC induction motor or Bldc motor..? Or both for same power requirement?
@mastermechanicaldesign
25 күн бұрын
Yes power required will be same for all types of motors
Please make video on Moment of inertia
@mastermechanicaldesign
5 ай бұрын
Noted !!
how to have its transfer function?
Excellent lecture bro, can u pls explain the calculation of acceleration time in detail
@mastermechanicaldesign
Ай бұрын
Ok noted !!
Need detail video regarding welding types , bearing selection and type gear and pully teeth calculation all those topics in separate detail video
@mastermechanicaldesign
10 ай бұрын
Sure 👍
Sir thank you so much i am always wanted to become a machine designer your video help me a lot. Regarding conveyor belt design you talk about MOI OF ROLLER . But if anyone used troughed idlers instead of instead of flat idlers then how i found his moment of inertia of in
@mastermechanicaldesign
4 ай бұрын
I'm so glad 😊 Trough rolls - as these are also rollers but at an angle. So we can also calculate the MOI same as roller. Don't need to be too exact. Just consider approximations at higher side.
Sir i want to now whole process of selection regarding gantry system vertical and horizontal movement with rack and pinion mechanism
@mastermechanicaldesign
11 ай бұрын
Okay 👌 Noted, Complete series
👏👏👏👏👏
@mastermechanicaldesign
11 ай бұрын
Thank you 😊
Sir please make a video on rack and pinion with gear box selection
@mastermechanicaldesign
9 ай бұрын
Noted Subham 😊
Please explain once the Servo press calculation and selection
@mastermechanicaldesign
11 ай бұрын
Hi Suresh, Servo motor selection calculation ??
Need a video on procedure for selection of timer belts
@mastermechanicaldesign
10 ай бұрын
Sure, Noted ☺️
Sir make video on motor selection of servo motor for shaft rotating
@mastermechanicaldesign
Ай бұрын
Noted !
Can you attachvexcel calculation sheet
Idler rotatating calculation video 😊
@mastermechanicaldesign
10 ай бұрын
Hi Pratik, To calculate the ideal roller speed, You can use the same formula of conveyor roller speed, only you have to put the ideal roller diameter instead of roller diameter. If Idea roller don't have much slips
Make a video on leak testing fixture pneumatic cylinder selection
@mastermechanicaldesign
10 ай бұрын
Noted, Manivannan 😊
sir, how did you select MOI for gearbox from catalogue? its not clear. and also when selscting a motor, why did you select from "4P 1500min-1" catagory?
@mastermechanicaldesign
7 ай бұрын
For motor selection start from 18:02 Gearbox MOI - Find J value in catalogue 16:25
Sir please make a video on moment of inertia in detail and how to use it in design.
@mastermechanicaldesign
Ай бұрын
Sure I will
I would clarify the no friction part. I think what you were saying was the first part was the load to move the belt and load at constant speed then the second part was to start the belt from rest to the set speed which would require the diameter of the rollers. Is this correct?
@mastermechanicaldesign
Ай бұрын
Yes that's what I'm trying to say.. when we will start the conveyor from rest. An extra torque will be required to move the belt because of MOI of everything.
@user-bi3zc7gd9i
Ай бұрын
@@mastermechanicaldesign thanks helps ALOT to know the nuance and can tackle other issues like if it was at an incline.
Hi which one is best to consider for doing the calculation, moment of inertia or without?
@mastermechanicaldesign
9 ай бұрын
Offcourse considering MOI will give you close value. But if the application is light, rollers are small, then its okay to ignore MOI calculation, just consider significant SOF, but not too much. Its also a problem (deeply explained in video)
@ravisaini-kl9nt
9 ай бұрын
appreciate for immediate reply I think for a long conveyor, the number of roller will high that mean total MOI also High and the equation will give the high value of power
@mastermechanicaldesign
9 ай бұрын
Yes exactly
Hi Sir can I ask where did you get or what book did that table of density came from?
@mastermechanicaldesign
5 ай бұрын
Hi, this table is taken from MISUMI (an automation products manufacturer)
Big Fan Broo .. ❤ please tell me what is the PPT model and animation you using for this presentation.. It's fantabulous..🎉
@mastermechanicaldesign
7 ай бұрын
Thank you so much mohan, PPT model - mostly i design models in solidworks and some images i took from internet. Animations - mostly i do in MS PowerPoint and also in solidworks animation. For b rolls - either i use stock videos or i shoot in workshop
I appreciate your help in providing me a brief equation or rule of thumb to calculate the specific energy consumption as Kwh/Mt/Km length = 5 Km , Flow = 2500 to 3000 Mt/Hr , Route inclination= zero inclination, Width = 1200 mm , trough angle=30 how much electricity will be consumed in electrical motor
@mastermechanicaldesign
6 ай бұрын
HI, Its very simple, 1. power consummation is equal to your conveyor motor required power. 2. 1 unit electricity is equal to 1 kW per hour. Let say your conveyor required motor power is 2 kW. Means your electricity consumption is 2 kW per hour means 2 Unit. -- for motor power calculation, refer formula of this video.
@tzb05
6 ай бұрын
@@mastermechanicaldesign the installed power is not the consumed power
@mastermechanicaldesign
6 ай бұрын
Yes, as i said, power consumption is equal to the required power to operate the conveyor (point 1)
@sambathbunkh
5 ай бұрын
Best explanation video
Please make detail videos of moment of Inertia for more clarity
@mastermechanicaldesign
3 ай бұрын
Sure, I'm planning for this
Thanks master,how to calculate chain conveyor
@mastermechanicaldesign
29 күн бұрын
I will make video on it, for sure
Pls make a video of moment of inertia
@mastermechanicaldesign
5 ай бұрын
Noted ☺️
Please tell us indepth about welding symbols its types and methods
@mastermechanicaldesign
11 ай бұрын
Sure Fenil, noted. In content list
Can you elaborate inclined convayor.
@mastermechanicaldesign
Ай бұрын
I'll make a video on it
Hello sir, can you please give us the link from where you got the belt table? thank you so much
@mastermechanicaldesign
2 ай бұрын
drive.google.com/file/d/1j4Ve0GKd1DWazmZe0ha41LC1eB5FeKxN/view?usp=sharing
@picklerick5159
Ай бұрын
@@mastermechanicaldesign thank you sir!
Sir put video make for material selection of product design
@mastermechanicaldesign
10 ай бұрын
Sure, Noted. My notebook has been full 🤭
Powered roller chain conveyor calculation par video banaye.
@mastermechanicaldesign
5 ай бұрын
Let me first finish this bearing calculation series. Also i have used a powered roller only once in my experience. So it will take some time to research. I hope you understand me.
Power and torque calculation for a shaft carrying cam and rotate with 150 rpm and cam also carrying a load of 200 kg
@mastermechanicaldesign
5 ай бұрын
Cam Shaft Torque = (Normal Force of cam follower on cam) X (distance from cam shaft center to point of contact between cam and cam follower) (tan a (pressure angle))
If the conveyor has an inclination what steps should be added?
@mastermechanicaldesign
5 ай бұрын
Hi, Aniket, In an inclined conveyor we have to consider a cosine value (angle value) in mass, which will add up into conveyor pull force
How to select the motor for driven purpose of a machine from one place to another can you able to prepare a video for that
@mastermechanicaldesign
5 ай бұрын
How do you want to drive.. Like on wheels or pick and drop. I mean I'm not fully understanding your requirement
@automationguy9760
5 ай бұрын
Can you able to share your WhatsApp num so that I can share the image of that machine so you can easily understand
COULD U PLEASE LET ME KNOW HOW TO CHOOSE MOTOR FOR Z OR INCLINE CONVEYOR.
@mastermechanicaldesign
8 күн бұрын
Yes, pull force become Pull force X cos A . (A - inclination angle)
sir we required your complet assembly desigen for study perpose
@mastermechanicaldesign
2 ай бұрын
Share your email id. I'll send you link
Can you make a video to design a motorised trolley which is moving on wheel and rail track, with loading capacity of 40 ton. For given speed 20m/min, calculate gearbox, wheel dia, motor power, ?
@mastermechanicaldesign
28 күн бұрын
Yeah sure
@Newonyou
28 күн бұрын
Yes waiting for this video.
Dear sir moi torque roller -0.25*15*(0.0225)2*2 value 0.0018 not available. Valve comes to 0.0037 please State whether this answer is correct or not
@mastermechanicaldesign
7 ай бұрын
Hi Swapnil, Yes there is few calculation mistyping in my video. So Your calculation should be correct 👍
Sir ek question hai for example if customer need 100 part in one minute at the end of conveyor then what should be belt speed...means how we will calculate belt speed???
@mastermechanicaldesign
10 ай бұрын
Hi Praveen very interesting question ❓ Here belt speed will also depend on part length. And gap between each parts Let say part length is 100 mm at a gap of 50 mm. Mean conveyor belt should travel 150 mm for one part delivery. And as given 100 part per minute. Mean 100x150 mm per minute 15000 mm per minute, 15 meter per minute. Please let me know if I'm making mistake in calculation 😅
Roller conveyor calculation par video banaye.
@engineeringfundamentals6958
6 ай бұрын
powered roller conveyor
@mastermechanicaldesign
6 ай бұрын
Okay, Noted!!
Is the diameter of the roller according to the motor or is it the design for the belt?
@mastermechanicaldesign
7 ай бұрын
According to me, diameter of roller should be according to belt thickness and belt material, like allowable minimum bending radius of belt top of that we should keep the roller diameter minimum just to keep MOI of rollers minimum also to save cost
@cesarbeltran6353
7 ай бұрын
@@mastermechanicaldesign it depends on the length of the belt too? for example I am designing a 10 meters belt with the same material you used in the video, how much diameter do you recommend to use for the roller?
Can you provide the entire transcript of calculation in pdf..as my simple guide in conveyor belt calculation.thanks in advance
@mastermechanicaldesign
8 ай бұрын
Okay 👍, Yes it would be useful
Roller chain conveyor calculation ka video banaye...
@mastermechanicaldesign
7 ай бұрын
Sure Vinayak, Noted!!
@vinayakbhoee6488
6 ай бұрын
Aayush Bhai waiting for Roller Conveyor Calculation.
hi sir, in the 20:26 second final velocity u gave 146.5 mm/sec but u didnt mentioned how it came there can u please explain it to me, Thanks for sharing the great video as usual awesome great content
@mastermechanicaldesign
7 ай бұрын
Its selected motor final speed- watch from 19:50 You welcome Srinivasan
@SrinivasanSeenu-bk8jw
7 ай бұрын
@@mastermechanicaldesign Thanks a lot sir😍
Why is the loading torque smaller than the starting torque in this video?
@mastermechanicaldesign
2 ай бұрын
Could you share time stamp
If u remove the belt support Whete will u keep the Loan ? In Air ??
@mastermechanicaldesign
2 ай бұрын
No. Load will remain over the belt. Conveyor without belt support - Yes for short distance and light weight material transfer like plastic parts we don't give support below the belt. But this is not the main purpose of this video with this example I just want to say. If you don't support the belt then it doesn't mean that required torque will become zero. There will be a MOI of rollers and other items. "Watch the entire video otherwise you will be confused, I'm not confused"
Is there any documents or validation documents for your calculation
@mastermechanicaldesign
7 ай бұрын
Not exactly. But i would say whatever I have explained is pure physics, like power formula, speed, MOI etc. Plus for data reference i have given is from manufacturers catalogue. Which you can verify. However if you need specific parts validation, then i can provide. In terms of formula.
Where can i find the source of that table of density ?
@mastermechanicaldesign
8 ай бұрын
In the belt Manufacturers catalogue, I have given the example from MISUMI's catalogue You download it from video discription.
@cesarbeltran6353
8 ай бұрын
@@mastermechanicaldesign thanks 🙏. I need help, i want the gearbox MOI for 0.55 kW. How do I look for it in the catalog tables?
@mastermechanicaldesign
8 ай бұрын
Yes, 16:17
Calculation for gradient conveyor?
@mastermechanicaldesign
8 ай бұрын
Calculations concept will be exactly the same, Just include the force cosine component as per conveyor gradient angle, (Like in sliding Friction, MOI of belt and load)
The video is great but check calculations do not match with the calculator
Weight needs to be calculated by volume x mass density, please recheck it.
@mastermechanicaldesign
2 ай бұрын
First of all this is mass, not weight density. Now as we all know.. Mass (Kg) = Volume (m3) x mass density (Kg/m3) Multiple by m/m = (m3 / m) X (kg/m3 x m) Mass (Kg) = Area (m2) x Area density (Kg/m2) We can say. Mass is equal to area into area density. Area density is nothing but mass per unit area for a specific thickness. As belt thickness is given
@dharmalingamv7447
2 ай бұрын
@@mastermechanicaldesign ok fine
Please reconsider moi of roller it should be 1/2 Mr2.....
1)If I have flat belt conveyor with drive pulley and driven but both are different diameter then belt speed is change or not 2)same question for timing belt
@mastermechanicaldesign
Ай бұрын
Belt speed will always depend on driver pulley. If both pulleys are the same dia. Both will rotate at the same speed. If driven pulleys is smaller, will run faster. If driven pulleys bigger, will run slower. Belt speed will be same.
@vivekmagar7776
Ай бұрын
@@mastermechanicaldesign 1. For flat belt is same belt speed if we change diameter 2 but belt speed changes in timing belt if both pulley teeth are different
frictional force = 0,2 x 411,5 x 9,81 = 807,3 N
@mastermechanicaldesign
9 ай бұрын
Yes, please bear with me for example calculation mistakes, take the formula and put your own required values. Apart from calculation typing mistakes every thing is right 👍
@santiagoaldohuamaniolivera7619
Ай бұрын
haha I was wondering where is the x2? 🤔, thank you.
Sir trunnion ball valve design calculation
@mastermechanicaldesign
2 ай бұрын
I can't help with this. I don't have experience in valve design.
I have a question, whether the formula above can determine a DC motor for a conveyor?😅
@mastermechanicaldesign
2 ай бұрын
Conveyor driving capacity. Like torque and speed will be the same for all types of motor
@bejrusxs4816
2 ай бұрын
@@mastermechanicaldesign Thank you sir, for replying to my question😁
Sir how to connect with you? I have a motion simulator design in mind and I want help in selecting motor and gearbox!
@mastermechanicaldesign
4 ай бұрын
You are allready connect with me 😊 please do DM on Instagram. Id is in channel description
@vedantjoshi1487
4 ай бұрын
Ok thank you so much 🙏
The frictional force is 807.36N , but the value is 1614.7 , we have to double it ?
@mastermechanicaldesign
11 ай бұрын
No, It's just trying mistakes, I don't know how to overcome typing mistakes, i really need a team to cross check. I'm the only one who does everything. And mistakes happens
Can you upload the video of Trajectory calculation with Example
@mastermechanicaldesign
3 ай бұрын
Yes, I'll upload on another channel, physical channel, not created yet. I'll let you know
@mastermechanicaldesign
3 ай бұрын
Yes, I'll upload on another channel, physical channel, not created yet. I'll let you know
@mastermechanicaldesign
3 ай бұрын
Yes, I'll upload on another channel, physical channel, not created yet. I'll let you know
@mastermechanicaldesign
3 ай бұрын
Yes, I'll upload on another channel, physical channel, not created yet. I'll let you know
What is the Area of belt L*W*T or 2*L*W 2 is thickness???
@mastermechanicaldesign
10 ай бұрын
In this example area density is given for 2 mm belt thickness, so only have to calculate Area = 2xLxW If mass density would given then Calculate volume Volume= 2xLxWxT
@Jor-hl3rr
9 ай бұрын
Belt is close loop, one layer on top and second under conveyor that's why= length×2