Marquee Numbers | How to build | Short version
Тәжірибелік нұсқаулар және стиль
In this video I explain my process for building 4' tall (50.25" with frame and base) marquee numbers.
I use 3/4" plywood and one number uses roughly 75% of a full sheet however all numbers will obviously vary.
Products:
20 Count Outdoor String Lights: www.walmart.com/ip/Better-Hom...
Tools:
Kreg Accu Cut: www.homedepot.com/p/Kreg-48-i...
Kreg Rip Cut: www.homedepot.com/p/Kreg-24-i...
13/16" Forstner Bit: www.woodcraft.com/products/wo...
Music found at www.epidemicsound.com (subscription required)
Пікірлер: 33
Beautiful made!!❤
Nice job
Thank you!
How tall are the side pieces that frame the number? And how much space do you leave on the back? One inch?
@twisteddesignco
6 ай бұрын
The sides are 6” and yes I leave 1” on the back
What angle do you leave in the corners?
Hello from Germany, i like your video. You mix the filler with water to fill it in the bottel. How many water you use? Thanks Gabriel
@twisteddesignco
Жыл бұрын
I use just enough to thin the filler without it being to watery however I have since started using white caulking
would like to know if you sell them , if so how much
How long did it take you to make a single marquee number?
What size hole did you use for the lights
@twisteddesignco
Жыл бұрын
I use a 13/16” Forstner bit, it’s the perfect size for the socket. This is the size I use for these lights
Nice job do you sell and ship them? If so how much?
@twisteddesignco
Жыл бұрын
My apologies for the terrible response time, I currently am not shipping these due to the cost being through the roof.
What kind of wood filler do you use?
@twisteddesignco
Жыл бұрын
I was using DAP Plastiwood filler but I have now started using white caulking to fill all the seems because it is much faster.
Can you give measurements for the base
@twisteddesignco
Жыл бұрын
The base is 18” front to back, the width is usually only a couple inches wider then the marquee bottom which can vary
@davisharogers7447
Жыл бұрын
@@twisteddesignco thanks for responding
Just made a 16 for my daughters party. How much do you rent them for?
@twisteddesignco
Жыл бұрын
I rent the 4’ Marquees for $98 each
@its_marc
5 ай бұрын
@@twisteddesigncohow long is that rental for?
Can you share link for the lights?
@twisteddesignco
Жыл бұрын
I use the better homes and garden 20ct string lights from Walmart
@chrismartinez5379
Жыл бұрын
Thanks brother, appreciate it
@CWills6385
Жыл бұрын
@@twisteddesigncothat’s what I used as well.
Which drill bit did you used to drill the holes?
@twisteddesignco
5 ай бұрын
With these lights which are the Better Homes and Garden 20ct from Walmart I use a 13/16” forstner bit, you can order one online or purchase them at a woodworking supplier like Rockler or Woodcraft
@sondrastanley7230
5 ай бұрын
What are you using to lift the number from the table when glueing the sides on?
@twisteddesignco
5 ай бұрын
@@sondrastanley7230 I cut 1” strips and place the underneath to get a 1” lip on the back side
@sondrastanley7230
5 ай бұрын
@@twisteddesignco thank so much
About how much does this weigh?
@twisteddesignco
11 ай бұрын
If I remember correctly they are around 30-35lbs