Nice work! Very interesting process

i always love your video pcp airgun for life

Nice work on the lathe

@pcpairgunschannel

Ай бұрын

Thanks 👍

great talent.good job bro🤜🤛

Thanks for this share

Internal diameter 23mm. 11.5x11.5x3,14=415 mm2 (4,15cm2) 1 bar=10N/cm2 4000psi = 276 bar. So… you hold back 276x 10x 4,15 N =11454 N with a couple of little screws. Reckon with only one; they don’t bear equally and when the first snaps, then the second may well go too. Mind that the screw itself M6 has a core surface of 2.38 x 2.38 x3.14 mm =17,8mm2. If the quality is 8.8, the tensile strength is 800 N per mm2, starting to yield at 80% or 640N. For a shearing load as the screw experiences here, we take 80% of that value. We are then left at 512N/mm2 x17.8 mm2 or a load of 9113N at which the screw will probably fail. With 11454N … you are a lucky bastard. And please, dont grease O rings on a cloth full of chips.

@pcpairgunschannel

Ай бұрын

this is a very common way to do it. the grub screws arent the only thing holding it but the inlet valve too, which is a lot thicker

@lukmankhakim5568

Ай бұрын

If I may know, what is the safe pressure for the tube?

@pcpairgunschannel

Ай бұрын

​@@lukmankhakim5568 the tube is 304 stainless steel, 27mm OD 2mm wall thickness. Using barlow's formula the burst pressure is 10958 PSI, and therefore the safe pressure would be 3652 PSI if we use 1:3 safety factor which is commonly used for air gun tanks.

@lukmankhakim5568

Ай бұрын

@@pcpairgunschannel For a tube thickness of 1.5mm, what is the safe pressure?

@pcpairgunschannel

Ай бұрын

@@lukmankhakim5568 Depends on the od, if you used a 27mm 304 SS tube like me, then 2700 PSI. 25 OD is more common for 1.5mm wall thickness tubes, for those it's 2958 PSI

Like pcp jowo 👍👍 good job my friend

@pcpairgunschannel

Ай бұрын

yes, its inspirated by indonesian pcp jawa

Nice sharing💖👍

@pcpairgunschannel

Ай бұрын

Thanks for visiting

Nice video mr..👍👍👍♥️ god job !

@pcpairgunschannel

Ай бұрын

❤️❤️❤️

This Video should called...how to build a bomb

Very Nice

Iki jelas wong indo seng ngerantau neng negara 4 musim. Nice project bro

@pcpairgunschannel

Ай бұрын

haha terimakasih mas

@kerahledrek

Ай бұрын

Ane dah curiga dr awal pemilik channel ini org indo sih wkwkkwk

@AnthonyTasin

27 күн бұрын

​PCP airguns channel UU you uuuuuuuuuuu uuuuuu7uuuuuuuuuuuuuuu😢 my pp

This actually call in my country is "pcp jowo/timbangan gaplek".....nice project👍👍

@pcpairgunschannel

Ай бұрын

Yes bro, this is heavily inspirated by indonesian PCP jawa

Nice work 👍👍 watching New friend from Phillipines 🤝🤝🙏👍👍

Excellent want more

@pcpairgunschannel

Ай бұрын

Coming soon

Please upload next part Love from India ❤👍

@pcpairgunschannel

Ай бұрын

coming soon bro.

thanks you br

Dang I wish I had a lathe this is sweet!

@pcpairgunschannel

24 күн бұрын

Currently I wish I had a milling machine as well 😅 The slots and all the holes were dissapointing, so I better save up for a mill too.

@Brett_M

24 күн бұрын

my dad has a super nice bridge port mill and a ton of nice tooling I just started to learn how to use. I can make square parts and you can make round parts 😆

@pcpairgunschannel

24 күн бұрын

​@@Brett_M so then let's do team work and make greater projects 😎

It's good to have the new toolsأ. Congratulations... great job. The best thing in the video is visualizing the sizes and dimensions.. Great work, keep it up and we are waiting for the rest of the manufacture of the air rifle from the reciger, the gun, and all the parts of all sizes and dimensions.. Greetings from Egypt

@pcpairgunschannel

Ай бұрын

Thank you very much❤️

Top mase salam dari indonesia❤

Top power

i think i know that minilathe model. You can easily disengage lead screw gears from spindle - it will make a lot less racket :)

@pcpairgunschannel

26 күн бұрын

Yes, I should do that. It is a vevor 7x16 mini lathe

How much possibility psi per single shoot , biggest air pressure on pcp

@pcpairgunschannel

20 күн бұрын

Max psi per shot with the spring i use is about 10 shots from 4000 PSI to 3200 PSI, so 80 PSI per shot. 80 PSI per shot gives me about 70 joule, or 1250 fps using 15.4 grain. However I don't know what higher consumptions would give, I don't have a spring that strong to test. I think if you just try to bring the usage to like 500 PSI per shot you are gonna get at least 100 joule.

Saya menantikan dan memimpikan power itu digunakan laras lubang 12mm, karena di Indonesia sangat mengerikan untuk dibuat 😅

@pcpairgunschannel

Ай бұрын

ya, saya dengar kaliber legal terbesar di Indonesia adalah 4,5 mm

Indonesian pcp ( pcp jawa ) 👍🏿👍🏿

@pcpairgunschannel

Ай бұрын

yes bro, i took inspiration from it.

你好我是你粉丝，能不能做一期做 slug 子弹的视频。

If possible, the valve shaft must use a thread to enter the Tevlon. Prone to breaking often hit by a hammer.

@pcpairgunschannel

Ай бұрын

It's ok, this will work

@BC-wj8fx

14 сағат бұрын

Many successful airguns do not use a thread. But they do not use Teflon, they use stronger plastics such as acetal, or PEEK for more strength. If the valve stem is very thin, a larger diameter metal insert can be pressed into the plastic, it does not need to be threaded.

@pcpairgunschannel

13 сағат бұрын

@@BC-wj8fx yes, this is POM

Part 2 next please

@pcpairgunschannel

Ай бұрын

in about 1 week it'll be done, still waiting for some materials to arrive.

👍👍👍👍

Pcp jowoooooooo

Que marca de torno é essa? Show.

@pcpairgunschannel

5 күн бұрын

Vevor 7x16

👍

This mechanism is recommended for high pressures

@pcpairgunschannel

Ай бұрын

Yes, 4000 PSI max

So far, that will only blow away snow. Where is the rest of the 4000psi Big Game pcp rifle? LOL

@pcpairgunschannel

Ай бұрын

Sir this is part 1, I will still build the chamber, Stock, trigger hammer etc

@Pierchinggun

Ай бұрын

Di Indonesia This 2mm Monel material is made with 6 bolts and a pressure of 4500psi. 180cc cal32mm 8shoot 1100fps can be produced.

@pcpairgunschannel

Ай бұрын

@@Pierchinggun i think 4500 psi is a bit too much. The burst pressure is 10800 PSI. depending on the steel alloy, of course.

Good video but I'm not sure I'd trust that with 4000 PSI

What kind of oil do you use for O-rings?

@pcpairgunschannel

Ай бұрын

Silicone oil, or any synthetic oil. Petrolum based oils will destroy the rubber. s.click.aliexpress.com/e/_Dl3RL1z

@jandeeg152

Ай бұрын

@@pcpairgunschannel Mind you, oil together with highpressure oxygen can be dangerous, you’d better use lithium grease. BUT……., your video is great!

@pcpairgunschannel

Ай бұрын

@@jandeeg152 yes, oils can combust under high pressure oxygen. But this is not pure oxygen I am using, its just air. Therefore combustion of the oil isn't likely

jeroane oblak bos😂

Joss

You finally got a lathe, how much did you pay for that and what brand?

@pcpairgunschannel

Ай бұрын

It is a vevor 7x16 mini lathe, it was 730$. Now lets see when I am getting a milling machine.

@airsight2753

Ай бұрын

@@pcpairgunschannel same price here, make a mini lathe review, i am planning to buy soon.

@pcpairgunschannel

Ай бұрын

@@airsight2753 let's see! 👍I'll be waiting to see what you'll make with a lathe!

21:16 I see a leak

@pcpairgunschannel

22 күн бұрын

that was just the unpressurized air bubbling away from the threads/what was between the valve and the tube. It's not from the tank. I have stored this for maybe a week at most while pressurized at 3000 PSI, a week later still at 3000 PSI.

I hope you can translate it into Arabic because it is not available in the video settings. Thank you for your wonderful effort

@pcpairgunschannel

Ай бұрын

I’ll look for time to add captions.

the barrel installation part bro

@pcpairgunschannel

Ай бұрын

yes bro, patiently wait for the rest of the building videos. Next I will make a trigger and a hammer to open the valve, then later on i will continue with chamber making etc....

@kiasubandari48

Ай бұрын

@@pcpairgunschannel okay, waiting for the next part, keep up the enthusiasm

MASHALLAH DEAR I WANT A PIECE OF TANK FROM PAKISTAN HOW I WILL GAIN IT

@pcpairgunschannel

Ай бұрын

Sorry bro I can’t send this overseas for legal reasons…

Pcp original made indonesia..

@pcpairgunschannel

Ай бұрын

yes, pcp jawa

Mấy ông này phải gặp VN họ làm bằng inox chạy ren hết chứ đồng nó rễ gia công nhưng làm chĩ kiểu này tháy nó không mấy an toàn

@pcpairgunschannel

Ай бұрын

đây là một cách phổ biến để làm điều đó

BG bisa pesan Senpan ka,,,dri ntt

@pcpairgunschannel

Ай бұрын

maaf mas, saya tidak bisa menjualnya

Why not use titanium alloy tubes

@pcpairgunschannel

Ай бұрын

You can but they are expensive

@huazhong208

Ай бұрын

@@pcpairgunschannel It’s a pity that China can’t play

@pcpairgunschannel

Ай бұрын

@@huazhong208 Yeah man, airgunning is definitely a fun hobby. Where are you from in China?

@huazhong208

Ай бұрын

​@@pcpairgunschannelSir I am from Jiangxi Province, China😄

@huazhong208

Ай бұрын

This steel pipe can withstand 3500psi, which is equal to 240bar? brother

Indonesia pcp big game

@pcpairgunschannel

Ай бұрын

😎

有点怕飞堵头

Bisa cod ke malaysia

@pcpairgunschannel

Ай бұрын

maaf bro, saya tidak dapat menghantar pakej saya atas sebab undang-undang. Saya hanya membuat video untuk orang ramai melihat pembuatannya

You probably won't be able to get a hammer to open your poppet valve. It has too much surface area and pressure pushing against it.

@pcpairgunschannel

Ай бұрын

I will, i can open it by hitting it with a steel rod like this, and it releases a good amount of air already (it may not seem like that in the video because the sound echoed all around). The hammer I will make definitely will hit at least as hard as I did with a steel rod

Rentan jebol

Mine unit pcp system, Java pcp

@pcpairgunschannel

20 күн бұрын

yes bro, this is inspired from PCP jawa

@adisaputra4667

6 күн бұрын

like a indonesian tradisional air gun in java

mini bomb??????????

BG mntaa no wa nya BG,spya sy hbng,dri ntt

и для чего нужна данная фигня ??????

@pcpairgunschannel

Ай бұрын

это бак и клапан пневматического пистолета...

@user-Berefin

Ай бұрын

@@pcpairgunschannel А стрелять он будет походу из за угла . Так как бьет эта длинная трубка с боку

@pcpairgunschannel

Ай бұрын

@@user-Berefin Нет, вы увидите в следующих видео

like indonesian pcp

@FeriIbah

Ай бұрын

PCP jowo bro😂

@vikiwahyudarmawan6374

Ай бұрын

@@FeriIbah nahh betull😁

@pcpairgunschannel

Ай бұрын

Yes, i took inspiration

@rizaniotox634

Ай бұрын

​@@pcpairgunschannelfirst look i thing you from indonesia or some place in asia, but when i check yuor profile you from finland 😂😂

@pcpairgunschannel

Ай бұрын

@@rizaniotox634 it's true

Sopp thuy duong lừa đảo nha các bạn