Mr Innovation, application, and effectiveness strikes again......

@unemployedredneckhillbilly2023

Жыл бұрын

Thanks. That's what happens when you take your tim. Thanks for watching.

Very nicely done . It looks great .

@unemployedredneckhillbilly2023

Жыл бұрын

Thanks. It worked out being fairly easy to make. Thanks for watching.

Weather's changing here south of Buffalo , ny . Be safe !

@unemployedredneckhillbilly2023

Жыл бұрын

Looks like you are going to get walloped. We just got an inch. Thanks for watching.

nice job, looks great

@unemployedredneckhillbilly2023

Жыл бұрын

Thanks. Another fun little project. Thanks for watching.

That looks so sharp. You'll be toasty. Just saw the weather forecast and depending on where the bands set up you may be using all your equipment. Stay safe and warm. We're in a secondary belt off Lake Erie but the wind needs to be more north-to-south to get us but it's coming, if not this storm then soon.

@unemployedredneckhillbilly2023

Жыл бұрын

Looks like we are going to get lucky with only a couple inches. I hope next weekend is nice though because we have a big Thanksgiving and Birthday celebration here on Saturday.. Thanks for watching.

Well done sir!

@unemployedredneckhillbilly2023

Жыл бұрын

Thanks for watching.

Looks great and the cardboard templates are the key to success. You are ready to tackle Old Man Winter in upstate NY.

@unemployedredneckhillbilly2023

Жыл бұрын

I start everything with cardboard. Measure 10 times and cut once with the cost of polycarbonate. We are ready and waiting. Thanks for watching.

Beautiful! Thanks for making this video. I have turned my airconditioner hole in the wall into a window because it's on the south side and I need as much sunlight as I can get in this tiny apartment. So I put a thin plexiglass at the outer edge of the box against, what looks like that diamond shape screen on your Gizmo, but they're smaller diamond shapes. And I don't know what I did wrong, maybe I didn't cut it enough to fit because it buckles in the middle sticking out toward the front end where the room is, and I think I may have to take it out to recut it on the edges. But I have this thicker plexiglass like the one you have there, for on top of the wood frame around the box. I'm going to put hinges on it, and like you were doing to insulate, I was thinking to put a thin strip of that flat rubbery plastic stuff that you find in rolls at the dollar store for putting on the bottom of cabinets for dishware. I hope it works. So yea, you gave me some inspiration to get back to it and redo that thinner piece of plexi that's closer to the outside so that I could seal out the weather. P.S. If you're wondering what I'll do in the summer for airconditioning, well, I heard there are in-room, plug in the wall, air conditioners...some new technology, that can keep the place cool. I think I'll invest in one of those.

@unemployedredneckhillbilly2023

Жыл бұрын

Yes plastic will expand big time in the sun. Polycarbonate will stand some buckling but you have to be careful with acrylic (plexiglass) that can shatter. Best to leave plenty of clearance and not fix it solid. There are many efficient ac units available these days that can vent through a hose. Thanks for watching

@Belialith

Жыл бұрын

@@unemployedredneckhillbilly2023 You know, you are SO correct about this and I am so glad I came across your chanel because I now know what the heck I'm dealing with. As I look at that piece of plexiglass in the end of the box window in the wintertime, being Dec. 25..by the way, Merry Christmas.. I notice how it fits perfectly in there, straight. Whereas when it was sunny and warm (on that south side) before now, it had buckled so it stuck out into the box with a curve rounding out through the middle. I am at a place where now I have to figure out what to do about that because I can't cut it seeing as it fits perfectly in while it's shrunk from the cold. Hm.

@unemployedredneckhillbilly2023

Жыл бұрын

@@Belialith Merry Christmas. You could probably just have a piece of glass cut 1/8 of an inch undersized and use window points to locate it with silicone caulking to hold it there and seal it. Most home centers will cut it to size.

@Belialith

Жыл бұрын

@@unemployedredneckhillbilly2023 That was the solution I was thinking about, a piece of glass.

I had a job where I cut a lot of poly carbonate, I found that a coarse tooth wood blade for the jigsaw worked best and I was cutting two half inch thick sheets at the same time. And a 24tooth thin kerf blade for a Skilsaw.

@unemployedredneckhillbilly2023

Жыл бұрын

I found the finer tooth blade gives an edge that doesn't need deburring. The fuzz wipes right off. I haven't had any luck with a circular saw. The heat generated by a wood cutting blade actually melts it leaving a terrible burr. Plexiglass on the other hand cuts fine. You must have a better blade. Thanks for watching.

@timberray9572

Жыл бұрын

@@unemployedredneckhillbilly2023 24tooth thin kerf DeWalt blades for the Skilsaw cuts an inch no problem.

Nice work, always interesting content. Wish I was as talented with fixing things.

@unemployedredneckhillbilly2023

Жыл бұрын

Thanks. Guess you haven't made enough mistakes to learn from yet. Thanks for watching.

Luckily I don't have my UTV anymore, but I thought about doing a Lexan windshield and back window and upper doors...since the manufacturer of my UTV never had a hard cab option, and their windshield and rear window were ridiculously over-priced a Lexan option would have been what I ended up doing as well. Nothing wrong with a DIY Lexan windshield and back window and door windows.

@unemployedredneckhillbilly2023

Жыл бұрын

I went with the glass windshield because it takes a beating that would scratch lexan but $4400 for a set of doors with seals, shipping, and tax from Kubota is ridiculous. I have no idea what they get for the back window. I think these will do the job once I get it all worked out. Thanks for watching.

Looks great! You really do a great job with what ever you do. You are so talented and really enjoy all of your videos. Thanks so much.Take care and God Bless! Chuck!

@unemployedredneckhillbilly2023

Жыл бұрын

Thanks. The world is watching so I better do a good job. Thanks for watching.

Hey Ed, I am watching your video now on my smart TV and I have an unrelated question for you. It sounds like your area is really in for a big snowstorms now and this weekend. Take care and maybe video a snow removal with your new toys. Getting cold and snow flurries today in Milwaukee too. Don from Milwaukee, Wisconsin

@unemployedredneckhillbilly2023

Жыл бұрын

Luckily most of it is staying west of us. As you know living by a big lake can cause big storms. Happy Thanksgiving. Thanks for watching.

@donz6901

Жыл бұрын

@@unemployedredneckhillbilly2023 , yes, Milwaukee does occasionally get the lake effect snow, but not as much as your area. I heard Buffalo Bills game will be played in Detroit instead of Buffalo. Happy Thanksgiving to you and family too.

How are you making out with the snow storm i just heard some places got 73"? Hope all is ok, looks like you got the plows on just in time.

@unemployedredneckhillbilly2023

Жыл бұрын

We have been very lucky so far. It all has stayed west of us with just a little nuisance snow. tonight we will get a couple inches and that should be it. lake Erie is a threat to the Buffalo area up until it freezes over in January. Should get to try it out tomorrow morning. Thanks for watching.

BATTEN down the HATCHS Here comes the SNOW!! Your Equipment should get a good WORK OUT!!!!!!

@unemployedredneckhillbilly2023

Жыл бұрын

It's that time of the year again. Thanks for watching.