Келесі
- 14:48
- 29 М.
- 9:11
- 2,7 М.
- 01:00
- 13 МЛН
- 11 күн бұрын
- 00:11
- 56 МЛН
- 13 күн бұрын
- 00:58
- 3,4 МЛН
- 3 күн бұрын
- 00:49
- 20 МЛН
- 10 күн бұрын
- 17:44
- 241 М.
- 5:41
- 3,4 М.
- 8:14
- 172 М.
- 8:05
- 14 М.
- 17:56
- 6 М.
- 15:02
- 161 М.
- 0:28
- 4,1 МЛН
- 1:00
- 7 МЛН
- 0:27
- 2,3 МЛН
- 0:20
- 4,7 МЛН
Пікірлер: 36
Interesting design! I built similar but made a U shaped part that holds the rings and bearings (brass/Teflon in my case) which allows the rings to be opened for removal of the OTA or rotating the OTA easily. I used a lazy Susan bearing to replace the record which turns better than my record allowed. I inserted a tiny 1/4" thrust bearing at the top of the center pivot which also helped the smooth operation. Fun stuff to play with.
How can I get this sketch?
Superb cool telescope 🔭❤️ dear, thank you for informational video... Fully enjoyed 😀💖🎁🎁🎁🎉🎉🎉🎉🎉
Nicely done.
Wow!😅
How much. I need a base
Very well done! Where I can find / buy the blueprint?
@PuddintameXYZ
3 жыл бұрын
Seconded
@drewcarruthers711
3 жыл бұрын
Seconded again
@PuddintameXYZ
3 жыл бұрын
@@drewcarruthers711 See other comment by myself. He doesn't have the plans anymore
@drewcarruthers711
3 жыл бұрын
@@PuddintameXYZ I read and know that - no harm asking again! see my others comments
@PuddintameXYZ
3 жыл бұрын
@@drewcarruthers711 👍
good job
Podría compartir los moldes??
Szép! Mivel telítetted a rétegelt lemezt? Vízállóságra gondolok.
@horvathtamas3476
5 жыл бұрын
Csónaklakkal.
I am here to add to the voices of the comment section in asking if you have any plans you might share for this.
@horvathtamas3476
3 жыл бұрын
Hello! It's an old design, the plans no more available.
@PuddintameXYZ
3 жыл бұрын
@@horvathtamas3476 Aw, too bad. Thanks anyway!
@drewcarruthers711
3 жыл бұрын
@@horvathtamas3476 please please please find the plans! who know you might be able to make a few $$
Nem mindenkinek van CNC gepe otthon!
@horvathtamas3476
4 жыл бұрын
Nekem sem volt, amíg nem terveztem és építettem. Nem csak cnc-géppel lehet zsámolyt készíteni!
I hate rock.
There was no information at all, only a few minutes of watching power tools. Nothing about why you did this, to cautions about what to look out for, no suggestions of other methods, nothing worthwhile. Too bad, because you went to a lot of trouble to make the video and the mount. Thanks anyhow.
@insaneinthemembrane383
Жыл бұрын
its not a tutorial
Terrible angry music really detracts from what you are trying to convey. Can't watch this ...
@RCzan13
4 жыл бұрын
I liked the music.
@Handles-R-Lame
4 жыл бұрын
Me too, work calls for work music. Star gazing calls for ambience. Man at work.
@Handles-R-Lame
4 жыл бұрын
Also very assuming of you to call it "angry" it may be peaceful to some.
Skip the crap music!
@horvathtamas3476
3 жыл бұрын
If it’s not your style, not my fault. You can switch off you speaker, while you watch the video.
@szaki
3 жыл бұрын
@@horvathtamas3476 When you go to a star party observing , you blast place with hard rock or techno music? Poor soul!
@horvathtamas3476
3 жыл бұрын
Dear szaki. This is not relevant. I obseving without any music or noise. This is two different thing, don’t mix them.
@crustyMilk
3 жыл бұрын
szaki wow youre a miserable tw**
@epic_playz4283
3 жыл бұрын
@@szaki lol