I KNEW THIS WAS POSSIBLE! Brilliant!

Super cool! Thanks for inspiring me to do this on one of my projects!!

Beautiful workmanship!

You earned my sub just for this video. I've started to complete my first projects, a few including this pattern seen in your video, and it's not easy... Not hard, just not easy. Lol so I commend you!

Cigar boxes come with a vaneer insert. My husband works at a smoke shop and has saved a bunch of them. This would be a perfect use! Thanks for sharing

I only wish you could visit Portugal so we could talk a little bit about our work! Ben... love your content... easy subscriber...

Nice..👍

That is so cool!!! I'm pretty excited about trying this! Where do you get the veneer from?

@danieltaylordesignermaker6028

3 жыл бұрын

Hi, Thanks! I'm glad you like it, I buy all my veneer from www.thewoodveneerhub.co.uk and I've never had a problem, though as they do ship the veneer rolled I've found it's best to buy a bottle of their veneer softenner and flatten the sheets you want to use to stop them from curling up whilst you work, Hope this helps!

@thomaskuzia8125

3 жыл бұрын

@@danieltaylordesignermaker6028 Thanks for the information!

Good

awesome! i have always been dying to try this... maybe i should start.. do you glue in between the pieces? because all the pieces looks like it is glued together after the tape was taken out?

@n0n339

2 жыл бұрын

He put tape on the other side before removing

May I ask what angle you used for you diamonds?

@danieltaylordesignermaker6028

2 жыл бұрын

Hi! the angle used to make this pattern is 60 degrees, this is so that the resulting rhombus shape has two 60-degree corners and two 120-degree corners, if you look at the image at the end of the video you can see how three 120-degree corners and six 60-degree corners sit together (3x120 or 6x60=360degrees) to make the complete pattern. I hope this helps! -Dan

What scalpel or marking knife is that?

@danieltaylordesignermaker6028

Жыл бұрын

Hi! The Scalpel is a Swann-Morton scalpel, specifically a Number 3 handle and number 10A blade. The blades do not stay sharp very long when cutting veneer but with how cheap they are to replace this hasn't been a problem for me and I like using a smaller sclpel blade rather than a large knife as it makes it easier to see what I'm doing.

How Thickness size veneer ? Thankyou

@danieltaylordesignermaker6028

3 жыл бұрын

Hi! I buy all my veneer in pre-cut sheets, so I don't thickness it myself. The thickness I buy is 0.7mm, which I believe is fairly standard for decorative veneers.

@hausanansullivan1939

3 жыл бұрын

I can use 0.3 mm.?

Have you had much buckling and wrinkling due to the glue? I'm sure I should be using the proper glue of course, but no need to explain why I use what I use I reckon. Lol. I had seen in a video where, when using wood glue, or pva glue, in order to diminish wrinkling, and such, you can add the glue normally to both sides, but then you let it dry fit some time... But fully cured but dry to the touch. Then, apply the veneer and using a bit of heat like a blow dryer or heat gun, heat the veneer and press, roll, or clamp as usual. This helps with any squeeze out causing issues as there's no real squeeze out. I haven't seen any sticking issues from this method either, and wrinkling, caused by the water in the glue is rendered moot, as the glue is dried and the veneer normalizes, then the heat reactivates the glue for application without moisture. What are your ways of dealing with wrinkling when gluing? Do you use veneer conditioner, it have any diy recipes for conditioner? Thanks homie!

@danieltaylordesignermaker6028

5 ай бұрын

Hi! Yes I have had several issues with buckling veneers in the past, in-fact you can see in this video (5:03) that this piece had quite significant buckling. After this I sought some advice from other woodworkers and the best solutions I found, and which have worked great for me since, have been: 1) Switching to titebond glue rather than PVA. it’s an aliphatic resin glue and from my experience it tends to affect the wood slightly less, it also dries harder and, as it’s thicker, is less likely to “bleed through” whilst clamping. 2) Use less glue! You can see in this video I add far too much glue, all that excess glue has moisture in so makes any swelling or buckling much worse. 3) Don’t leave clamped for too long. This seems counter-intuitive but it works! When the laminate is clamped air cannot get to the face of the veneer, this means the moisture from the glue has nowhere to go and soaks into the wood, causing it to swell and buckle. If the piece is released from the clamps after 2 hours the glue will have already set the design in place, and will cure much quicker in open air, giving the veneer much less time to absorb moisture and swell. (the box lid in the video was clamped for 24+hours and I think this is the main reason for the swelling seen) I have also seen people create their own heat-stick veneers like you describe above, but I’ve never done it myself so can’t comment on how well it works! I use a veneer softener to flatten curved veneers when I buy in rolls, but don’t use any other conditioner no. I just use an off-the-shelf option form online. Hope this helps! -Dan

@jarredmattingly5369

5 ай бұрын

@@danieltaylordesignermaker6028 thanks for the response! Great advice! Currently, I'm doing some designs that require smaller pieces, and usually that means each piece is literally hand cut to fit perfectly... Not exactly easy but here's some unsolicited advice regarding process. A lot of times I'll cut the final cut with an under bevel and a bit longer than needed because of the measure twice thing but also because the under bevel hides the other cut which probably isn't perfect anyways, while not adding thickness. This really helped all my pieces look flawless (not really just way more proud of them). Additionally, I started using CA for these projects and haven't looked back. It's much easier for a bunch of little pieces than one large veneer, to use CA, I think... But for repairs that require smaller pieces, CA glue works great!

Hi cc