In this episode we finish up fabrication of a heavy duty engine stand made with steel 2x4's, a wheel hub from a Chevy Impala and a friction brake from a go kart.
Жүктеу.....
Пікірлер: 21
@gerardfenn39882 ай бұрын
Watching you tinker with your shop lathe and machines brings me back to High School as they were the machines I used when in Brooklyn Technical High School. They were great times and I am always fascinated by what a man and a lathe can do. Great Video. I will give you a 98% for your ingenuity.
@barriejones1511 ай бұрын
I followed all three videos, nice work, doing the best with what you've got/can source. We all make mistakes, great you can admit to yours, might make others think twice before making the same. Thanks for your efforts.
@RoadHead62Ай бұрын
I'm surprised you didn't source that splined shaft from a wrecking yard. The outer CV joint housing would make a great axle for the drive unit.
@YoshimoshiGarage
Ай бұрын
I definitely considered it, and I still think it would have been the better route. But it was the middle of winter when I did this, and at the time I just couldn't overcome the idea of driving all the way to a pick and pull, wandering around in crap weather to find a donor, and pulling the part when I could just click a button. If I'm honest, age and the internet have made me soft.
@TheProchargedmopar2 жыл бұрын
👍💪
@damnimcooltom12 жыл бұрын
It's only for Chris.
@YoshimoshiGarage
2 жыл бұрын
Totally
@markhuyette85097 ай бұрын
you should have welded the handle to the hub
@besitstookeezbeshzhacuz9371 Жыл бұрын
Fuckin awesomeness bro
@papergatorzfedducca7998 Жыл бұрын
How did you mount the engine? Do you have a video showing an engine mounted to it?
Would have been easier, for sure. But I didn't have one.
@classicstangbrn8964
2 жыл бұрын
@@YoshimoshiGarage , I would have hit the junkyard, but I don't have your skill of fabrication.
@YoshimoshiGarage
2 жыл бұрын
If I'm honest, I was too lazy. The nearest yard isn't that close, and I didn't feel like doing a pull. Of course a week after I finished this, a friend replaced his hubs and CV axles on a Cherokee, so it would have been a great donor.
@papergatorzfedducca7998
Жыл бұрын
So how does the engine mount to this?
@classicstangbrn89649 ай бұрын
What no hydraulic master cylinder, lol?
@mounirtheking100 Жыл бұрын
to many items and tools ,bey it easyer and cheeber
@ALGAKZ2 жыл бұрын
Loot at my engine stand on my chanel
@pmd77719693 ай бұрын
Waste of time. Lol
@YoshimoshiGarage
3 ай бұрын
Totally, but more productive than sitting on KZread commenting of videos.
Пікірлер: 21
Watching you tinker with your shop lathe and machines brings me back to High School as they were the machines I used when in Brooklyn Technical High School. They were great times and I am always fascinated by what a man and a lathe can do. Great Video. I will give you a 98% for your ingenuity.
I followed all three videos, nice work, doing the best with what you've got/can source. We all make mistakes, great you can admit to yours, might make others think twice before making the same. Thanks for your efforts.
I'm surprised you didn't source that splined shaft from a wrecking yard. The outer CV joint housing would make a great axle for the drive unit.
@YoshimoshiGarage
Ай бұрын
I definitely considered it, and I still think it would have been the better route. But it was the middle of winter when I did this, and at the time I just couldn't overcome the idea of driving all the way to a pick and pull, wandering around in crap weather to find a donor, and pulling the part when I could just click a button. If I'm honest, age and the internet have made me soft.
👍💪
It's only for Chris.
@YoshimoshiGarage
2 жыл бұрын
Totally
you should have welded the handle to the hub
Fuckin awesomeness bro
How did you mount the engine? Do you have a video showing an engine mounted to it?
@YoshimoshiGarage
Жыл бұрын
kzread.info/dron/xFDpL91JoDVCzKR5tNVePQ.htmlcommunity?lb=Ugkxp6n-q2MV9RtnEH41tyGFwVDOIhFLKADu
Could have used an axle.
@YoshimoshiGarage
2 жыл бұрын
Would have been easier, for sure. But I didn't have one.
@classicstangbrn8964
2 жыл бұрын
@@YoshimoshiGarage , I would have hit the junkyard, but I don't have your skill of fabrication.
@YoshimoshiGarage
2 жыл бұрын
If I'm honest, I was too lazy. The nearest yard isn't that close, and I didn't feel like doing a pull. Of course a week after I finished this, a friend replaced his hubs and CV axles on a Cherokee, so it would have been a great donor.
@papergatorzfedducca7998
Жыл бұрын
So how does the engine mount to this?
What no hydraulic master cylinder, lol?
to many items and tools ,bey it easyer and cheeber
Loot at my engine stand on my chanel
Waste of time. Lol
@YoshimoshiGarage
3 ай бұрын
Totally, but more productive than sitting on KZread commenting of videos.