MAKE STIHL 194T GREAT AGAIN!!! TIMING/MUFFLER MOD Doing a timing advance and muffler mod on stihl 194t follow on tt and ig poplar mechanic
Жүктеу.....
Пікірлер: 63
@ServicestarOy11 ай бұрын
Ive done the same to 193t and its totally worth it! 👍🏻
@PoplarMechanic
11 ай бұрын
It definitely is. I should have got one sooner. I think I like it better than the 2511 😆
@EddieTM-gj3vt11 ай бұрын
I was able to use my 194 today on some ceder pine . Great saw very economical.
@PoplarMechanic
11 ай бұрын
It really is a great saw! Thanks for watching 🤙
@jaythe306snowmexican11 ай бұрын
Those are awesome little saws.
@PoplarMechanic
11 ай бұрын
Ya, I love it. Thanks for watching. I have to check out your Milwaukee video. I want one 😆
@jaythe306snowmexican
11 ай бұрын
They aren't a bad little saw but honestly, your new little 194 will out cut the Milwaukee and a tank of fuel will be the same as 2 batteries.
@mississippijohn143211 ай бұрын
Great job, thanks for the info.
@PoplarMechanic
11 ай бұрын
Thanks for watching 🤙
@gregbrown927111 ай бұрын
The 261 loves the advance too 👌
@PoplarMechanic
11 ай бұрын
🤙
@user-sh4vs7zs9l11 ай бұрын
Great job buddy ! I didn't fall asleep either lol.
@PoplarMechanic
11 ай бұрын
😆 thanks for watching
@user-sh4vs7zs9l
11 ай бұрын
@@PoplarMechanic you're the best ❤️
@carlobernardi138711 ай бұрын
Ahhhhhhhhhhh thanks broooo nice work..👍👍👍
@PoplarMechanic
11 ай бұрын
Thanks, man! She's a ripper. 💯🤙
@Planktarded11 ай бұрын
Great title, great thumbnail, and a great channel name.
@PoplarMechanic
11 ай бұрын
Thanks brotha 🤙
@darrengarlough512111 ай бұрын
Older tree guy from Ohio here. I wish you lived down the street I would come over and pester you to do my saw.
@PoplarMechanic
11 ай бұрын
I wish you did! I would definitely do it! That 194 turned out great. I love it. Thanks for watching 🤙
@EricNeilson_3 ай бұрын
She sounds good bud!
@PoplarMechanic
3 ай бұрын
Thanks brotha 🤙
@bobroberts89144 ай бұрын
Flip flops...nice
@PoplarMechanic
4 ай бұрын
😄
@MateuszBPM9 ай бұрын
And what is the ignition advance angle before top dead center?
@PoplarMechanic
8 ай бұрын
I'm not sure. I just know advancing from stock definitely gives more power.
@stevebrough30411 ай бұрын
Nice, is this the saw that I won? 😂 Thanks for the video.
@PoplarMechanic
11 ай бұрын
😆 thanks for watching brotha 🤙
@nicholaslacroix77225 ай бұрын
How much richer did you have to run it for the exhaust mod? Also did you take it off and do the other side baffle too?
@PoplarMechanic
5 ай бұрын
I just did the one side. I just backed it off to the limiter, I believe. So turn it left until it hits the limiter.
@nicholaslacroix7722
4 ай бұрын
I did mine and I went to richen it and it was already wide open! So I snipped the limiter and tuned it by ear until it sounded 2 stroke like and called it good. Might need to advance the timing now too, but was also thinking about drilling some more holes in the baffle and trimming the raised lip at the deflector so it doesn’t have ti go up and around the little shroud to exit
@motomikebuilder3 ай бұрын
Do you run 94-110 octane? I did mods to my 2 stroke street bikes in the 70' and 80's. I'm not sure if the advance mod will work with my 192 tc or not. I think it has a key. Any suggestions?
@PoplarMechanic
3 ай бұрын
You can take the key out and file or grind one side, then put it back. It will work. Obviously, you have to make sure the side that goes in the fly wheel is not ground
@PoplarMechanic
3 ай бұрын
Yes, I run high octane in all my saws
@PoplarMechanic
3 ай бұрын
Oops, correction. Grind only the fly wheel side of the key. I have done it with a file without taking it out
@motomikebuilder
3 ай бұрын
@@PoplarMechanic thanks. I'll do 'em all and let ya know. City boy with southern hillbilly roots here.
@motomikebuilder
3 ай бұрын
@@PoplarMechanic A chrome expansion chamber wood be cool
@louieintrees10 ай бұрын
Where can i find the right bolts to put to dogs on??
@PoplarMechanic
10 ай бұрын
They are the same ones that fit the 201. Probably online or at your local dealer
@adumboone2 ай бұрын
What bolts did you use for the wcs dogs?
@PoplarMechanic
2 ай бұрын
Ones from an old 201 I'm pretty sure. It was a while ago
@adumboone
2 ай бұрын
@@PoplarMechanic gotchya. Didnt know if you bought the ones from wcs. I interchanged dog bolts from an e h 355 to tbe 2511 and one bolt was too long and busted through the oil reservoir! Lol wasnt a problem until I took the bolt out though
@veteransowhat566911 ай бұрын
What other equipment do you work with?
@PoplarMechanic
11 ай бұрын
Like work with? or mechanical stuff? My mechanic skills are minimal. I work with skid steers, lifts, chippers and stump grinders
@blackandwhite80217 ай бұрын
Where is made ?
@Sethhaun7811 ай бұрын
Maybe I just ran a bad one but it seemed off ..was another tree guys he loved it .but I'll take me echo mate
@Sethhaun7811 ай бұрын
Quarter pitch is way superior..for tophandle saws wouldn't run anything else..it just cuts way better ..Lazer cuts
@PoplarMechanic
11 ай бұрын
For sure! Thanks for watching 🤙
@SpaceExplorer316 ай бұрын
Is modding the muffler alone give it a boost?
@PoplarMechanic
6 ай бұрын
Yes. Just fatten up the high jet a bit.
@SpaceExplorer31
6 ай бұрын
Sorry I’m not to mechanical. Do you mean open up the high jet hole a little bit ? Thanks
@PoplarMechanic
6 ай бұрын
@SpaceExplorer31 Yes. Basically, the muffler mod will improve air flow, causing a leaner condition. Turn the H jet to the left to increase the fuel. If the limiter stops you, it should still be fine butted up against the limiter. That saw is way better with an open muffler. Enjoy!
@SpaceExplorer31
6 ай бұрын
Thanks!!!
@PoplarMechanic
6 ай бұрын
@@SpaceExplorer31 🤙
@alotl1kevegas86011 ай бұрын
Isn't that funny looking bar technically for wood carving?
@PoplarMechanic
11 ай бұрын
No, it isn't for wood carving. The 150 comes with the 1/4 bar
@alotl1kevegas860
11 ай бұрын
I must of been mistaken. I was told the 1/4" bars with the skinny nose were for carving. Maybe it just looks funny in the video, or my eyes are shot lol.. I'm going to do the timing mod on my 193t later today.
@nicksanders914011 ай бұрын
I.meant bore me with all the cutting😂
@PoplarMechanic
11 ай бұрын
😆 thanks for watching 🤙
@nicksanders914011 ай бұрын
Bore me
@giannicaponera29337 ай бұрын
La motosega a tanta compressione.Per farla partire da problemi.E' priva di decompressore!
@PoplarMechanic
7 ай бұрын
If it has pullback when you start it, you may have advanced it too far. Mine is still going strong
Пікірлер: 63
Ive done the same to 193t and its totally worth it! 👍🏻
@PoplarMechanic
11 ай бұрын
It definitely is. I should have got one sooner. I think I like it better than the 2511 😆
I was able to use my 194 today on some ceder pine . Great saw very economical.
@PoplarMechanic
11 ай бұрын
It really is a great saw! Thanks for watching 🤙
Those are awesome little saws.
@PoplarMechanic
11 ай бұрын
Ya, I love it. Thanks for watching. I have to check out your Milwaukee video. I want one 😆
@jaythe306snowmexican
11 ай бұрын
They aren't a bad little saw but honestly, your new little 194 will out cut the Milwaukee and a tank of fuel will be the same as 2 batteries.
Great job, thanks for the info.
@PoplarMechanic
11 ай бұрын
Thanks for watching 🤙
The 261 loves the advance too 👌
@PoplarMechanic
11 ай бұрын
🤙
Great job buddy ! I didn't fall asleep either lol.
@PoplarMechanic
11 ай бұрын
😆 thanks for watching
@user-sh4vs7zs9l
11 ай бұрын
@@PoplarMechanic you're the best ❤️
Ahhhhhhhhhhh thanks broooo nice work..👍👍👍
@PoplarMechanic
11 ай бұрын
Thanks, man! She's a ripper. 💯🤙
Great title, great thumbnail, and a great channel name.
@PoplarMechanic
11 ай бұрын
Thanks brotha 🤙
Older tree guy from Ohio here. I wish you lived down the street I would come over and pester you to do my saw.
@PoplarMechanic
11 ай бұрын
I wish you did! I would definitely do it! That 194 turned out great. I love it. Thanks for watching 🤙
She sounds good bud!
@PoplarMechanic
3 ай бұрын
Thanks brotha 🤙
Flip flops...nice
@PoplarMechanic
4 ай бұрын
😄
And what is the ignition advance angle before top dead center?
@PoplarMechanic
8 ай бұрын
I'm not sure. I just know advancing from stock definitely gives more power.
Nice, is this the saw that I won? 😂 Thanks for the video.
@PoplarMechanic
11 ай бұрын
😆 thanks for watching brotha 🤙
How much richer did you have to run it for the exhaust mod? Also did you take it off and do the other side baffle too?
@PoplarMechanic
5 ай бұрын
I just did the one side. I just backed it off to the limiter, I believe. So turn it left until it hits the limiter.
@nicholaslacroix7722
4 ай бұрын
I did mine and I went to richen it and it was already wide open! So I snipped the limiter and tuned it by ear until it sounded 2 stroke like and called it good. Might need to advance the timing now too, but was also thinking about drilling some more holes in the baffle and trimming the raised lip at the deflector so it doesn’t have ti go up and around the little shroud to exit
Do you run 94-110 octane? I did mods to my 2 stroke street bikes in the 70' and 80's. I'm not sure if the advance mod will work with my 192 tc or not. I think it has a key. Any suggestions?
@PoplarMechanic
3 ай бұрын
You can take the key out and file or grind one side, then put it back. It will work. Obviously, you have to make sure the side that goes in the fly wheel is not ground
@PoplarMechanic
3 ай бұрын
Yes, I run high octane in all my saws
@PoplarMechanic
3 ай бұрын
Oops, correction. Grind only the fly wheel side of the key. I have done it with a file without taking it out
@motomikebuilder
3 ай бұрын
@@PoplarMechanic thanks. I'll do 'em all and let ya know. City boy with southern hillbilly roots here.
@motomikebuilder
3 ай бұрын
@@PoplarMechanic A chrome expansion chamber wood be cool
Where can i find the right bolts to put to dogs on??
@PoplarMechanic
10 ай бұрын
They are the same ones that fit the 201. Probably online or at your local dealer
What bolts did you use for the wcs dogs?
@PoplarMechanic
2 ай бұрын
Ones from an old 201 I'm pretty sure. It was a while ago
@adumboone
2 ай бұрын
@@PoplarMechanic gotchya. Didnt know if you bought the ones from wcs. I interchanged dog bolts from an e h 355 to tbe 2511 and one bolt was too long and busted through the oil reservoir! Lol wasnt a problem until I took the bolt out though
What other equipment do you work with?
@PoplarMechanic
11 ай бұрын
Like work with? or mechanical stuff? My mechanic skills are minimal. I work with skid steers, lifts, chippers and stump grinders
Where is made ?
Maybe I just ran a bad one but it seemed off ..was another tree guys he loved it .but I'll take me echo mate
Quarter pitch is way superior..for tophandle saws wouldn't run anything else..it just cuts way better ..Lazer cuts
@PoplarMechanic
11 ай бұрын
For sure! Thanks for watching 🤙
Is modding the muffler alone give it a boost?
@PoplarMechanic
6 ай бұрын
Yes. Just fatten up the high jet a bit.
@SpaceExplorer31
6 ай бұрын
Sorry I’m not to mechanical. Do you mean open up the high jet hole a little bit ? Thanks
@PoplarMechanic
6 ай бұрын
@SpaceExplorer31 Yes. Basically, the muffler mod will improve air flow, causing a leaner condition. Turn the H jet to the left to increase the fuel. If the limiter stops you, it should still be fine butted up against the limiter. That saw is way better with an open muffler. Enjoy!
@SpaceExplorer31
6 ай бұрын
Thanks!!!
@PoplarMechanic
6 ай бұрын
@@SpaceExplorer31 🤙
Isn't that funny looking bar technically for wood carving?
@PoplarMechanic
11 ай бұрын
No, it isn't for wood carving. The 150 comes with the 1/4 bar
@alotl1kevegas860
11 ай бұрын
I must of been mistaken. I was told the 1/4" bars with the skinny nose were for carving. Maybe it just looks funny in the video, or my eyes are shot lol.. I'm going to do the timing mod on my 193t later today.
I.meant bore me with all the cutting😂
@PoplarMechanic
11 ай бұрын
😆 thanks for watching 🤙
Bore me
La motosega a tanta compressione.Per farla partire da problemi.E' priva di decompressore!
@PoplarMechanic
7 ай бұрын
If it has pullback when you start it, you may have advanced it too far. Mine is still going strong