Asap. Positive response is highly appreciated. Thank you so much

Great 👏! Add ALARM like the Pid video. Thank you

Nice video

Very useful

Amazing... But I wonder is this controller works with movable weighing belt and how many set points in it your replay will be appreciated..

Amazing 👏! But how do you add alarm/action (hopper, light etc.) once the SV is reached?

Hi, may I know how can the readings of weight be stored in a pc?

Thank you ATO Automation for this video. I have a question regarding the calibration. If you mount the eye bolts to be able to hang the load cell, won't there be a deviation in the calibration? Or a shift in the zero point? Is not it better to hang the load cell and then calibrate by attaching a weight to the load cell? Thank you in advance!

@ATOcom

4 жыл бұрын

It can be calibrated in the plane, and the display needs to be cleared after installing the lifting ring. Zero drift will only appear after a long period of use, just recalibrate.

hi, I just wondering, would it be safe to connect this load cell indicator to a 240 V AC power supply?

@ATOcom

4 жыл бұрын

Can't connect it to 240V

Hello, Iam looking for a load cell that can register dynamic force at 1kHz, is it the same what to calibrate a load cell for that like you did in the video?

@ATOcom

4 жыл бұрын

Sorry, This video is only for ATO products.

We are getting Error 1 if we want to set calibration do you have advice

Does that AL1 and AL2 alarms have output on relay? Can I set weight (on AL1 and AL2) that will cause high state on relay?

@ATOcom

4 жыл бұрын

yes

If your outlet is 220v, do you need a trasnformer or can you plug it directly into wiring socket?

@ATOcom

4 жыл бұрын

No need transformer in the video type. www.ato.com/5-digit-display-controller-for-pressure-sensor

Thank you for your video .. Can you help to how to factory reset to the load cell controller?? Please

Hi, very nice video well explained, I have a question for you Sir, the two relays of this controller, what is their job? You can set the desired value (weight) for activation and deactivation of the relay?

Sir i have a question, I have used this controller on a packing machine. Control the two valves through alarm 1 and alarm 2 load cells. But after a circle is completed, alarm 1 and alarm 2 start working automatically again after 10 sec Please suggest me how to turn this time off or increase it.

Sir, Plz tell inno load cell calibration settings

Hello, iam an intern at a startup looking to build a static test bed for a high power rocket motor( with total impulse in the range of 15000N.s, i.e, with peak loads of more than 500kg). My question is, can this be used along with an arduino? If so, what kind of amplifier do we need? Will the likes of ATO-LCS-TJL-1 be able to measure loads as small as 40kg? I hope that you do answer my queries, seeing as a lot of recent comments have been unanswered. Thank you in advance!

@ATOcom

2 жыл бұрын

1. We have weighing transmitters that convert weight signals into analog signals or digital signals, maybe this can be used for your arduino. www.ato.com/load-cell-transmitter-output-0-5v-4-20ma www.ato.com/digital-load-cell-amplifier-output-4-20ma-0-10v-rs485 2. ATO-LCS-TJL-1 can measure loads less than 40kg. www.ato.com/tension-load-cell-s-type-50kg-to-20-ton

@anirudhdiwakar987

2 жыл бұрын

@@ATOcom thans for the reply!

Good day, thank you for the video it is a great help. Regarding the holding of the "Peak Value" how can this be set ? I am using a load cell on the end of a Linear Actuator to evaluate the force needed to break the bond between two parts. I would thus need a high sampling speed, and to hold the Peak Value. Will this unit be able to do this ? and how can I set this ? Thank you for your help.

@ATOcom

3 жыл бұрын

Its sampling frequency is 10 times/second.The peak setting method is in the instruction manual.

@aiman4917

Жыл бұрын

Hi.. Have u found the solution for your question. If u dont mind, can u share how to use that peak function.

@Boerikoe

Жыл бұрын

@@aiman4917 Good day, No I couldn't find how to set this in the instruction manual. I changed to a FUTEK unit.

@aiman4917

Жыл бұрын

@@Boerikoe Can u provide me the link to buy that model?

Hello. Do this device have an output 0-10v or 4-20mV to connect it to a PLC? Do you have it for sale in your store? Thank you.

@ATOcom

4 жыл бұрын

Sorry, we don't have it.

@pakistanmotarway8096

4 жыл бұрын

Sir You computer Waiting bridge To lose weight from Show the way

Sir shift up zero pick Ko set Karna hai kaisay karagay

sir I have a question, potentiometer can control speed right(yes) then will it work to use load to control speed?

@ATOcom

3 жыл бұрын

Maybe you need a load cell transmitter to change the weighing signal to 0~10V or 4~20mA to facilitate the speed control of the motor. This link for you, www.ato.com/load-cell-transmitter-output-0-5v-4-20ma Because the output signal of the load cell is difficult to directly use as the speed control of the motor.

Can you make video on Gefran 40 controller Calibration, using strain gauge

@kiranchoudhari4717

3 жыл бұрын

and 0-10V output for ref.

Добрый день что лучше купить это контроллер или contronix

Hola para configurar AlPHA 2 de Ditel

Hello! Can I ask how to reset all the parameters?

@ATOcom

4 жыл бұрын

Did you buy this model?

@aggelosnik5898

3 жыл бұрын

I have bought this model too and i need to know how to reset to factory!

Price pls Load indicator out 0 to10v 4 to 20m for plc

@ATOcom

2 жыл бұрын

I guess you need a weighing transmitter, see the price link below. www.ato.com/load-cell-transmitter-output-0-5v-4-20ma www.ato.com/digital-load-cell-amplifier-output-4-20ma-0-10v-rs485

Hi, it seem too slow display

Berapa harganya ?

Sale pehle karna ikhle

ขอเบอร์หน่อยครับ